The specification for Maximum Data Transfer Size (MDTS) says this field
should include the length of metadata, if metadata is interleaved with the
logical block data. However, some drives can support MDTS without counting
the interleaved metadata, so for this case SPDK will only use data length
without interleaved metadata length.
Change-Id: I29920a25885699e2689be043b87122367be0e416
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6813
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch really uses the accelrated engine.
Currently, we only offload the crc32c caculation,
but it can be extended.
Change-Id: If0e4c6a44b6e1e10e03f7eca355bed418d67326b
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6760
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Separate bdev_nvme_reset() and _bdev_nvme_reset() by making
bdev_nvme_reset() call _bdev_nvme_reset_start(), and then
remove the ctx parameter from _bdev_nvme_reset().
This clarifies the next patch and reduces the size of the next patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I76b0f2f5b83445845a313203e594dca0be150bc3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6949
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The recent refactoring removed the destruct poller and change the
reset processing to destruct ctrlr after its completion by conditionally
sending message.
But differentiating callback function is difficult if we reset multiple
ctrlrs.
If nvme_bdev_ctrlr->destruct is set, any new reset cannot start. So we can
use an new variable and always execute the callback function.
Add an new variable pending_destruct to struct nvme_bdev_ctrlr, and set
pending_destruct if ctrlr->ref is zero and ctrlr->destruct is true, and
then start destruct ctrlr if ctrlr->destruct_after_reset is set after
clearing pending resets.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9f34c42a40c5a5da54611e7871aef8c58117a56a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6714
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The following patches will cache and use spdk_nvme_ns pointer rather than
nvme_bdev_ns pointer in I/O paths. As a preparation, change a few cases
to get spdk_nvme_ctrlr pointer from spdk_nvme_ns.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ief5f01f85f46e2ad822af5b5abb13a14f28a0c6a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6834
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
When there still exists any NVMe bdev, if the bdev subsystem starts
shutdown, spdk_bdev_unregister() is called first. To avoid regression
for this scenario, add a test case.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5f484bda2ee2f3eaca364968a79ec7bf50267980
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6936
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Although this is not a mistake, it's better to add a semicolon to
be consistent with other DEFINE_STUB.
Change-Id: I5953b4612659d4115cb7735b1617eb8c13400798
Signed-off-by: wanghailiangx <hailiangx.e.wang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6653
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The NVMe Zoned Namespace Command Set Specification has, in addition to a
Max Open Resources limit, a Max Active Resources limit.
An active resource is defined as zone being in zone state implicit open,
explicit open, or closed.
Create a function spdk_bdev_get_max_active_zones() in the generic SPDK
zone layer, so that this limit can be exposed to the user.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I6f61fc45e1dc38689dc54d5649c35fa9b91dbdfc
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6908
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Purpose: To setup an accelerated function callback
for created spdk_nvme_poll_group. In this patch,
we just create the interface. The real usage of this
call back will be provided in the other patch.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I0d936aa4eba4dbfcc0137942156b9f2919eb5b78
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6758
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
There was no unit test for bdev_nvme_get_ctrlr().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ia69f0afdba2d3fb31bc38526834edcfc56a69c71
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6921
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: <dongx.yi@intel.com>
Previously, not nvme_bdev_ctrlr but spdk_nvme_ctrlr pointer had been
passed to spdk_get_io_channel() in nvme_rpc_io_cmd_bdev_nvme().
There was no unit test for bdev_nvme_get_io_qpair(), and so add
unit test for it to guard us from degradation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I00fdc14ea6467162c5fb90d04389883d7c409a17
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6920
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
spdk_bdev_io_complete_nvme_status() had set the bdev_io status to
NVME_ERROR even if it is aborted, i.e, sc is ABORTED_BY_REQUEST.
Fix it to ABORTED, and verify the fix by unit tests.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6b22547105a6d7986747053f93875854336959b3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6884
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add test cases for abort request. Both success and failures cases
and both NVMe and admin request cases are added.
The next patch will fix a bug that the status of the bdev_io which
was aborted was set to SPDK_BDEV_IO_STATUS_NVME_ERROR. The status
should have been SPDK_BDEV_IO_STATUS_ABORTED.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4fa885b874507e1a4cf9d70f45e37c4aaef2134a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6883
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: <dongx.yi@intel.com>
Add test case for admin command passthrough to test redirection
of completion processing.
Change the type of opc to uint16_t to cover admin commands.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Id01cb924e7778878dcfaf8766b05af1ae52623eb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6882
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: <dongx.yi@intel.com>
Community-CI: Mellanox Build Bot
Make stub for external APIs, cases for getting lkey
and constructing ctrlr.
Change-Id: I1b453139e98b297616d839de66690947c6f19738
Signed-off-by: Mao Jiang <maox.jiang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6529
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is an internal API used in several places. The call can fail, so
make sure it can report that correctly.
Change-Id: Iac0ed2c8299c9dd3d2556070278a2224c3807b7b
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6640
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
include test_nvme_ns_set_identify_data,
test_spdk_nvme_ns_get_values(Most functions that simply get values),
test_spdk_nvme_ns_is_active,
and spdk_nvme_ns_supports(Judge whether extended_lba and compare are supported).
The above func is completed.
Signed-off-by: ChengqiangMeng <chengqiangx.meng@intel.com>
Change-Id: I916173a195692045ee0ee3fa408a1696e0eb5b1e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6511
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Mellanox Build Bot
Add mutex per nvme_bdev_ctrlr and replace g_bdev_nvme_mutex by it
for possible cases. These are just drop-in-replacement.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ib1d5eebd65e514cfe96ad60a9004d9bace7b4f6b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6693
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This will make us easier to maintain the operation to delete
nvme_bdev_ctrlr and its trids. The added unit test cases guard us
from degradation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I400d4092020e89bacaebc7be045a456b8760ed8d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6688
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
The following patches will refactor bdev_nvme_remove_trid() and merge
it into bdev_nvme_delete(). Add test cases for bdev_nvme_remove_trid()
to avoid degradation by the following patches.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I42da17c62843ead9a30ab9a06463df4b679e561d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6686
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
spdk_bdev_part_base_construct() is deprecated so this patch
moves remaining instances to spdk_bdev_part_base_construct_ext().
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Iccd4b15933bec41885adfaf4fc4ce2abedd2d6c7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6627
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Leverage SO_INCOMING_CPU to get the CPU affinity of connections
(sockets). And allocate the connections to specific poll groups,
which aims to utilize cache locality.
From our test:
6 P4600 NVMe on target,target uses 8 cores, NIC irqs are bound to
these 8 cores, and initiator side uses 24 and 32 cores,
we can get 11%~17% randwrite performance boost for posix, and 8%~12%
for uring.
Change-Id: I011e0a21502c85adcccd4a14fbe9838b43f54976
Signed-off-by: Richael Zhuang <richael.zhuang@arm.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5748
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Cases for IO message sending and processing.
Change-Id: Id9085c016d4379401f8e203006e11a268518d0e2
Signed-off-by: Mao Jiang <maox.jiang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6215
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
On some platforms, GCC identifies that opts.io_queue_requests is used
uninitialised in bdev_nvme_create_qpair due to the stub function
spdk_nvme_ctrlr_get_default_io_qpair_opts which would normally zero the
qpair opts. Whether the warning appears is likely to be determined by
how effectively the platform garbage collects unused code.
Replace the stub with a minimal implementation that zeros the qpair
opts to avoid the warning.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I2b8c2d657ae5401c3b35ca66938a966906cdc846
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6595
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
nvme_tcp_parse_addr code comprehensive coverage.
res->ai_addrlen is returned by getaddrinfo(), and it is an IPV4 or IPV6 address, so its maximum length is not more than 46.
And sizeof(*sa) is always 128,so ai_addrlen cannot be greater than sizeof(*sa).
Signed-off-by: ChengqiangMeng <chengqiangx.meng@intel.com>
Change-Id: Id432a39c1461c484ea871e7e9d8d3ed7a8391200
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6512
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Mellanox Build Bot
The spec does not disallow TEXT PDUs with no data. In that
case, just return immediately from iscsi_parse_params.
This avoids a NULL pointer dereference with a TEXT PDU that has
no data, but CONTINUE flag is set.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I2605293daf171633a45132d7b5532fdfc9128aff
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6319
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This change follows the large read which submits only subtasks, and
simplifies large write cases.
Associate the PDU which sends a SCSI Write PDU with immediate data
with both the primary task and the first secondary task. Then stop
incrementing reference count of the primary task twice.
As same as the last patch, copy the failure status directly among
the primary task and the secondary tasks because the primary task
is not submitted now. Then remove related data from struct
spdk_iscsi_task and related helper functions from conn.c.
Finally simplify unit tests for process_non_read_task_completion().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I54aa38c9b9fb7d7352da040dcdd8bcc1b1756a83
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6344
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
nvme_rdma_ut.c:370:9: warning: missing braces around initializer [-Wmissing-braces]
struct nvme_rdma_qpair rqpair = {0};
^
Designated initializers is used with scalar value
while the first element of nvme_rdma_qpair is
a structure
Change-Id: I5a4e76612ccbd2c84283fe3ae2c57b9ea98591cf
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6305
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: <dongx.yi@intel.com>
When multipath is supported, nvme_bdev will be got via bdev_subsystem.
To make such change transparent, add a helper function
nvme_bdev_ns_to_bdev() and use it for some cases.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ia5ad0b87178bc739ba0a75789f9f26b860241a04
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5801
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
By the recent changes, the linked list nvme_ns->bdevs has only a
single bdev at the maximum. Hence replace it by the pointer
nvme_ns->bdev, and remove the linked list pointer nvme_bdev->tailq.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ib976e15bb128ba8479070b58e5f4c43fb9dcf479
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6230
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
By the last changes, not only standard namespace but also ocssd
namespace has only one nvme_bdev, and standard namespace processes
only the head of nvme_ns->bdevs.
This patch changes the common and standard namespace specific
part to process only the head of nvme_ns->bdevs.
The following patch will replace the linked list nvme_ns->bdevs
by the pointer nvme_ns->bdev.
Add a particular error case that nvme_bdev is failed to create even
if ctrlr has one namespace. If ctrlr has one namespace but the
corresponding bdev is failed to create, nvme_ns->populated should
be false and hence nvme_ns->bdevs should not be accessed. However
the code had not assumed such case.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5495882fad8c8a012305177179a46d4373ba75f5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5800
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch provides two new accelerated crc32c function interface.
And the next patch will be used to add the real support of chained crc32c feature.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I3f8dd55c3da636e29e5fb02fc229b51f05653cd6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6456
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
When read is split, only secondary tasks are submitted. Hence we can
copy the failure status directly among secondary tasks and primary
task now.
Additionally, improve the comment in the source code to make us easier
to understand.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I857711dfaf90515231048f8c31c9273eac854d28
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6343
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Implementation is pretty solid now, add first test with many
more to follow.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I4b80f3108fcd07919949bcd14dadfdfeb10c45fd
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6332
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Remove ocssd_bdev_parameter from bdev_ocssd_from_disk_lba(),
bdev_ocssd_to_disk_lba(), and bdev_ocssd_to_chunk_info_offset()
including unit tests.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iaf52e3e33609e9f1fe13050e95020bad688dc6ae
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6223
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
It has been confirmed that there is no affected use case in
the SPDK community when we remove the range parameter from
the bdev_ocssd_create RPC.
Hence, remove the range parameter from the bdev_ocssd_create RPC,
remove range parameter from bdev_ocssd_create_bdev(), remove range
info from ocssd_bdev_config_json(), and then update unit tests
accordingly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I1b0a541b61bf26732fd028dc43becb7ca2384f8e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6220
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Test bdev_nvme_submit_request() for all supported I/O types
including comare and write.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I8c3e7e1b93307329e9cc55692fa3e0e8c291a5b5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6190
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Add a test case for AER. It includes populating, depopulating, and
resizing namespaces dynamically.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ib00c3279142cbdd70a0d571baee5797e661bb963
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6138
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Add stub of struct spdk_nvme_qpair and related APIs, and test cases
to reset or failover nvme_bdev_ctrlr. They include a case that destruct
and reset are executed concurrently, and a case that two reset requests
are submitted concurrently. For failover, the test cases are for a single
trid or two trids.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6538a4dc32a73d0d72d6cac2a48c79ea7f00d332
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6132
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add framework for unit tests of bdev_nvme, and add a very simple
test case to create and destruct a nvme_bdev_ctrlr first.
Following patches will add more test cases and dynamic stubs.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I98f07d58d469949f3dac5a0bd36a3963de8dc3d1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6131
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
We already have support for spdk_nvme_zns_zone_append(),
add support for spdk_nvme_zns_zone_appendv() (zone append with
NVME_PAYLOAD_TYPE_SGL).
_nvme_ns_cmd_rw() currently performs verification of the SGL,
if the parameter check_sgl is set. This parameter is set for all
calls with payload of type NVME_PAYLOAD_TYPE_SGL.
In order to be able to perform the same check_sgl verfication on
zone append vectors, we need to refactor _nvme_ns_cmd_rw() a bit.
Setting check_sgl ensures that _nvme_ns_cmd_split_request_sgl() or
_nvme_ns_cmd_split_request_prp() gets called.
These functions will split an oversized I/O into several different
requests. However, they also iterate the SGE entries, verifies that
the total payload size, total SGE entries is not too many, and that
buffers are properly aligned. A proper request will not get split.
For zone append, splitting a request into several is not allowed,
however, we still want the verification part to be done, such that
(e.g.) a non first/last SGE which is not page aligned, will cause
the whole request to be rejected.
(In the case of spdk_nvme_ns_cmd_write(), a non first/last SGE which
is not page aligned will instead cause the request to be split.)
An alternative would be to try to rip out the verification part from
_nvme_ns_cmd_split_request_sgl() and _nvme_ns_cmd_split_request_prp().
However, that is non-trivial, and would most likely end up with a lot
of duplicated code, which would easily get out of sync.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I2728acdcadeb70b1f0ed628704df19e75d14dcca
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6248
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Unit tests for spdk_strtol/spdk_strtoll use hard coded strings for
arithmetic constants (LONG_MIN/MAX etc). These are only valid
on platforms where both long and long long are 64-bit values.
Replace the hardcoded values with strings generated from limits.h.
The tests use values that are outside of the MIN/MAX range, which
cannot be represented as int64_t. These are calculated in two parts
to avoid overflow and recombined as a string.
Verified using the unit tests on two different architectures and with
test code to check that the generated string is the same as the
hardcoded value on x86 Linux. Used a small test program to calculate
+/-30 around each limit value to check carry handling and boundary
conditions.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I990ff354f568a0b35853ecc849dd2a452bb1048b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6048
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
There is a special case when using 8-byte metadata + PI + PRACT
where no metadata is transferred to/from controller.
Since _nvme_ns_cmd_rw() already calculates the proper sector size
using _nvme_get_host_buffer_sector_size(), which takes PRACT into
account, change the sectors_per_max_io calculation to also take
PRACT into account.
This will avoid certain requests that don't need splitting getting
split.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I8d450d37c2458453701189f0e0eca4b8fe71173b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6247
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This function allows applications to specify whether
they wish to allow probing a newly attached NVMe
PCIe SSD.
The env layer will only even probe devices that have
been allowed. By default, this is all devices, but
if the user has specified some list of
allowed PCI addresses (via spdk_env_opts pci_allowed)
then newly attached PCIe devices are implicitly not
allowed. This API allows applications to add
device addresses to the allowed list after the
application has started.
This API will be useful for use cases where multiple
SPDK processes are running on one server, and assignment
of PCIe SSDs to those processes are based on some function
of the SSD's PCIe address.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I919bc267f2ad9130ab5c875ff760a301028b047e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6184
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Fixes#1777.
When a qpair cannot be allocated because the transport connection fails,
the qpair was freed without unlinking it from the other structures.
This was leading to a segfault when attempting to create and free other
qpairs.
Also added a unit test to cover this case.
Change-Id: I74b78d1847f90117248b07203b43a11ff5cfa5d6
Signed-off-by: Vasuki Manikarnike <vasuki.manikarnike@hpe.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6272
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed when finished. Add mutex initialization and destroy
calls to io_valid_test.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: Idbbf857f3103ba15ab851ed16ce9f4e2bc99f7dd
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6218
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed before the memory is zeroed. Add mutex initialization
and destroy calls to test_nvme_pcie_hotplug_monitor.
Tested with a pthreads library that contains debugging code to
check the mutex state.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: Ifd770a85627a11e2b2c6643f798f796bab10b6cb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6153
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Community-CI: Mellanox Build Bot
For flow control reasons we have to resize the bit arrays we
use to manage flow as channels come and go. However since
channels are assigned to devices, until the channel count
reaches the device count there's no sharing so no resize of
the array is needed. So, when we use a device for the first
time there's no need to run through the rest of the channels
and re-balance.
Same thing is done on destruction. The code to free idxd
specific resources was moved from the rebalance function to
the idxd put channel function which is a much more logical
place for it as well.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ib4df163286906f413dd6429dc6833af7b68e208c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5846
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Config #1 remains what is shown as an example in the spec. Change
config #0 to just have 1 work group and 1 work queue all backed
by 4 engines. As the majority of initial use cases will not be
implementing separate priorities and/or different back end
targets (mem, pmem, etc) having just 1 group and work queue makes
the most sense as it allows the silicon to decide which engine to
use.
Also, having multiple work queues spreads out the available
entires such that if we're not using all of the work queues then
we're not using all of the resources. As channels are created
they are assigned the next available device. As a channel is
assigned a device that is already in use it will round robin
work queues. If then, for example, we have 16 devices then only
the first work queue will ever be used for the first 16 threads
which seems and if there are even just 2 work queues per device
it would take 32 threads to use all of the resources at the
device.
By haing just one work queue per device we always have the max
number of work queue entries available regardless of how many threads
are being used.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ie15ff6bdea12525fe3bfc769613084ddd2de50bf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5845
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
If the CUnit include files are located through CFLAGS rather being
in one of the system include directories, then the version test will
fail and blob.c unit tests will be skipped. Specify CFLAGS as part of
the CC command.
If the version check fails, clean won't be run to remove any left over
artifacts. This can occur if CUnit is being built externally and gets
cleaned before SPDK. Add an extra definition (ALL_DIRS) to control
compilation, so that clean will always be run.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I6099fceb14cfc6473a6b8feed746d2b44b8d291a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6054
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For correct behaviour, pthread_mutex must be initialized before use.
Add static initialization to a couple of structures containing a mutex.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I7049824bb292135dbebab201083a1858597f94d1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6124
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed before the memory is zeroed. Add mutex initialization
and destroy calls to test_nvme_init_controllers.
Tested with a pthreads library that contains debugging code to
check the mutex state.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I9a0509bee176940e1aa46bd5de4c6ad396b787e1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6152
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed afterwards. Add mutex initialization to
DECLARE_AND_CONSTRUCT_CTRLR and add DECONSTRUCT_CTRLR
to cleanup afterwards.
Tested with a pthreads library that contains debugging code to
check the mutex state.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: Ifefec17b44ac01769fd9d041119fa093b4e9d8b2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6155
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed afterwards. Add mutex initialization to
DECLARE_AND_CONSTRUCT_CTRLR and add DECONSTRUCT_CTRLR
to cleanup afterwards.
Tested with a pthreads library that contains debugging code to
check the mutex state.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: Id1d62e6f76548bd8e259d4d9c4d453a3218b0b1c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6159
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed afterwards. An already initialized mutex should not
be re-initialized.
Remove the call to mutex_init from setup_qpairs since it will be done
in nvme_ctrlr_construct.
Add calls to nvme_ctrlr_construct where nvme_ctrlr_destruct is
called without a matching construct.
Add missing calls to mutex_init and mutex_destroy as required.
Tested with a pthreads library that contains debugging code to
check the mutex state.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I0ee97a70d67157668cd8921fbee03d976d4d607d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6161
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Documentation for vhost target states that CPU mask must be a subset
of application CPU mask. This wasn't enforced right now and allowed
the cpumask on controller creation so long as at least single
CPU core overlapped with application's CPU mask.
This might have been misleading and covered up user configuration errors.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I03f959ec37efd0be9b98cff9c93c5f996b04af35
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6212
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
`--cpumask` argument for vhost controller creation was
untested. This patch specifies this argument and verifies output
under following conditions:
- no cpumask, resulting in it being equal to the app cpumask
- cpumask equal to app cpumask
- single core
- single non-main core
- two cores
It was motivated by recent changes to reactor code affecting
vhost without it being caught by CI. See commit 7cc83b62.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I92c603061619092007bc27a189d3d8787461a16f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6211
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Add the real support in nvme tcp transport.
Change-Id: I2aa9b0284d6fe009925e67f602a055e787f77987
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5734
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This patch is used to add spdk_nvme_poll_group_get_optimal
public API.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Iee34c89e0e1ff1f81167b18e198c144ca28f71de
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3311
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Additionally, the user can specify a namespace to also pause during the
operation.
This allows for the management of hosts, listeners, and the addition of
namespaces all while I/O to other namespaces is occurring. Pausing a
specific namespace also allows for the removal of that namespace without
impacting I/O to other namespaces in the subsystem.
Change-Id: I364336df16df92fe2069114674cb7a68076de6fb
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4997
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
We want to avoid an active for_each_reactor operation
while the reactors are being shut down.
Fixes issue #1766
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I30bc258c5b22545320080d269a1ed8cb0b4e12f2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6104
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There is a chance that admin qpair is being destroyed at
the moment when IO qpair is added to a controller due to e.g.
expired keep alive timer. Part of the qpair destruction process
is change of qpair's state to DEACTIVATING and removing it
from poll group. We can check admin qpair's state and poll
group pointer before sending a message to poll group's thread
and fail connect command.
Logs and backtrace from one CI build that hit this problem:
00:10:53.192 [2021-01-22 15:29:46.671869] ctrlr.c: 185:nvmf_ctrlr_keep_alive_poll: *NOTICE*: Disconnecting host from subsystem nqn.2016-06.io.spdk:cnode1 due to keep alive timeout.
00:10:53.374 [2021-01-22 15:29:46.854223] ctrlr.c: 185:nvmf_ctrlr_keep_alive_poll: *NOTICE*: Disconnecting host from subsystem nqn.2016-06.io.spdk:cnode2 due to keep alive timeout.
00:10:53.374 ctrlr.c:587:41: runtime error: member access within null pointer of type 'struct spdk_nvmf_poll_group'
00:10:53.486 #0 0x7f9307d3d3d8 in _nvmf_ctrlr_add_io_qpair /home/vagrant/spdk_repo/spdk/lib/nvmf/ctrlr.c:587
00:10:53.486 #1 0x7f93077ea3cd in msg_queue_run_batch /home/vagrant/spdk_repo/spdk/lib/thread/thread.c:553
00:10:53.486 #2 0x7f93077eb66f in thread_poll /home/vagrant/spdk_repo/spdk/lib/thread/thread.c:631
00:10:53.486 #3 0x7f93077ede54 in spdk_thread_poll /home/vagrant/spdk_repo/spdk/lib/thread/thread.c:740
00:10:53.486 #4 0x7f93078366c3 in _reactor_run /home/vagrant/spdk_repo/spdk/lib/event/reactor.c:677
00:10:53.486 #5 0x7f9307836ec8 in reactor_run /home/vagrant/spdk_repo/spdk/lib/event/reactor.c:721
00:10:53.486 #6 0x7f9307837dfb in spdk_reactors_start /home/vagrant/spdk_repo/spdk/lib/event/reactor.c:838
00:10:53.486 #7 0x7f930782f1c4 in spdk_app_start /home/vagrant/spdk_repo/spdk/lib/event/app.c:580
00:10:53.486 #8 0x4024fa in main /home/vagrant/spdk_repo/spdk/app/nvmf_tgt/nvmf_main.c:75
00:10:53.486 #9 0x7f930716d1a2 in __libc_start_main (/lib64/libc.so.6+0x271a2)
00:10:53.486 #10 0x40228d in _start (/home/vagrant/spdk_repo/spdk/build/bin/nvmf_tgt+0x40228d)
Change-Id: I0968eabd1bcd532b8d69434ad5503204c0a2d92b
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6071
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: <dongx.yi@intel.com>
spdk_reactor_set_interrupt_mode will send event to set
reactor into interrupt mode or poll mode, also set every
notify_cpuset on all reactors for consistency.
It can be used by RPC method or scheduler to set
reactor to interrupt mode while workload is lightweight.
Currently, this function is limited that the specific
reactor should have no attached spdk_thread.
Change-Id: I7e8f449bff1184b9a7948f80b9572066a19da60f
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5853
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Each bit of the cpuset indicates whether a reactor
is going to be in interrupt mode.
Each spdk_cpuset is allocated to each reactor. So it
can only be touched by its reactor.
Change-Id: Ic186de341588b701d7471bf09336309d28b1bf4e
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5850
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
We don't want to make main core 100% busy, so don't
move thread to it if thread busy time is higher than
main core idle time.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Ib521ac0d8959ec8062322ff7b2ad587d85ccada5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5638
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Use DPDK based governor to change first core frequency
in dynamic scheduler. Core frequencies are adjusted
based on relative usages.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Ibeb9ca59fd67df27cfb0bfe752e66e5eef41b126
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5438
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This scheduler will group idle threads on first available
core and balance busy threads on other cores.
Change-Id: Ia0425c767dc3da2a66a9d82a20a0012fac83163c
Signed-off-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3901
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
The Zone Append command is an optional command in the Zoned Namespace
Command Set.
Zone Append differs from a regular write, in that the command is not
given an exact LBA of where to write the data.
Instead the user has to set the zslba field to the start of a zone,
and the data will be appended to that zone.
The actual LBA where the data was stored is returned in the
spdk_nvme_cpl, where Dword0 contains 31:00 of the ALBA field,
and Dword1 contains bits 63:32 of the ALBA field.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: Iabae1b3456bfbb62c07b63d79afe9a14e460fe83
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6013
Community-CI: Broadcom CI
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There are some common data structures and APIs in pcie transport
which can be used both for pcie and vfio-user transport, so move
the common code into a new header and source file.
No actual logic change just the code movement except remove the
static function declarations.
Change-Id: Ie9021e703a5780fdd6840f0e3cfea76a0017a811
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5923
Community-CI: Broadcom CI
Reviewed-by: sunshihao <sunshihao@huawei.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add two async API for Directive Send and Directive Receive.
spdk_nvme_ctrlr_cmd_directive_send;
spdk_nvme_ctrlr_cmd_directive_receive;
Signed-off-by: sunshihao <sunshihao@huawei.com>
Change-Id: Icb6974f74902df1512a5ffa9835188132634291b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5803
Community-CI: Broadcom CI
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
According to kernel, use an inline function spdk_nvme_bytes_to_numd
to transfer paload_size form bytes to numer of dwords.
Signed-off-by: sunshihao <sunshihao@huawei.com>
Change-Id: I8b9ded122bbf4a3c8e46988993ea52404783c0b0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5926
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
GCC 4.8.5 compains on missing braces:
nvme_tcp_ut.c: In function 'test_nvme_tcp_req_complete_safe':
nvme_tcp_ut.c:456:9: warning: missing braces around initializer [-Wmissing-braces]
struct nvme_request req = {0};
^
nvme_tcp_ut.c:456:9: warning: (near initialization for 'req.cmd') [-Wmissing-braces]
nvme_tcp_ut.c:458:9: warning: missing braces around initializer [-Wmissing-braces]
struct nvme_tcp_qpair tqpair = {0};
^
nvme_tcp_ut.c:458:9: warning: (near initialization for 'tqpair.qpair') [-Wmissing-braces]
Also structure spdk_nvme_qpair is embedded into nvme_tcp_qpair,
there is no need in a separate variable.
Change-Id: I3a9d6760a0cffe90ece0a6d470dda8309a6619e7
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5985
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: <dongx.yi@intel.com>
Community-CI: Mellanox Build Bot
Record result of spdk_env_get_last_core() to
g_reactor_count, since spdk_env_get_last_core()
iterates through all core ids in a loop, it is
not so efficient.
Change-Id: I6bbbfec0bc25490bab33436c84fca3da6380cbe8
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5955
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Since now min supported DPDK version is 19.11, we can
remove handling of buffer that may be split over several
Memory Regions as it was specific for DPDK < 19.05
Change-Id: I61a79c80b864e3bdde134e8bff6622025ea578a7
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5937
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
In this patch, we will use the accel library to do the crc32 work for the
header digest when sending the pdu in the target side.
For data digest support, will consider in the further patch.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I3169a158afd633f48bdbeb2cce1ed20e4141ae45
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5472
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch is for packed ring and recover the ring
base when vhost target reconnect to QEMU.
Change-Id: I73f791b4a55adf9834112afd7dd7bb26c75a135d
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4128
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Need to manage how we store IO context based on DPDK updates
made in 19.11.
Fixes issue #1671
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: If1183808cd30987b6c999912f563949b7ade7fcb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5799
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Community-CI: Mellanox Build Bot
This fixes issue where scheduler is not being
initialized on first set.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I881438955f08852fb72187a2b92c7acfb12cd662
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5029
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
As LLD cleanup is asynchronous in nature, Pass the
spdk_nvmf_transport_destroy_done_cb to LLD and it will be called
once the cleanup is completed.
Dont forcefully remove fc_ports by nvmf_fc_port_cleanup function.
LLD will drive the fc_ports cleanup gracefully as part of nvmf_fc_lld_fini.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: I537b9ea817eda26a0469114821e2288d2ba9d91c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5827
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Currently we dont have an api to delete fc port. Add SPDK_FC_HW_PORT_FREE
api. This is useful in cases of hardware reset and other error cases.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: Ib1b986ee7ab2f54043bd300b52121b651c292e5b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5810
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
1) As part of nvmf_fc_adm_evnt_hw_port_offline event, We try to remove
hwqps from pollgroup but we dont actually wait the action to complete.
Wait for the action to complete before completing nvmf_fc_adm_evnt_hw_port_offline
as this will serialise things nicely.
2) Protect fgroup->hwqp_count inside the transport lock as there can be
races where an fgroup can be removed paralley.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: Ib7af6bc0641c91e40331da2b2a7e72b5f55d54ae
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5808
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Current SPDK thread library has a issue which occurs if there is
a race between exiting thread and unregistering io_device.
For example, there are two threads. Thread 1 registers a device
and thread 2 gets a channel of the device. Then if thread 1 starts
exiting and unregisters the device, and then thread 2 puts the channel,
thread 2 sends a message to thread 1 to complete releasing the device,
thread 1 already moved exited. Hence thread 2 failed to send the
message.
This patch fixes the race issue. The code is verified by adding
a unit test case.
In detail, add a count, unregistering_dev, to struct spdk_thread,
increment it if a callback is specified to spdk_io_device_unregister(),
and then decrement it in _finish_unregister(), and thread_exit()
checks if it is zero.
The contents of struct spdk_thread is changed but it is not public
data structure, and hence suppress it for ABI testing.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Idf5faa55335c3ea89f47ccce32687a6be2e26c68
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5796
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
In the stress test of NVMe TCP (ARM platform, 6 nvme disks),
we see nvmf_tcp_req_set_state() takes quite some CPU cycles
(about 2%~3% of the nvmf_tgt process, ranking 6) moving TCP
request structure between different queues. And after some
analyzes, we think these actions can be saved. With this change
we get 1%~1.5% performance gain overall.
Change-Id: Ifd2f5609e4d99cab9fea06e773b461ded6320e93
Signed-off-by: Rui Chang <rui.chang@arm.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5667
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
According to 12.19 in iSCSI 3720.
"If DataSequenceInOrder is set to No, Data PDU sequences may be
transferred in any order."
So if the DataSequence is negotiated with "No", then we can
send Datainpdu in out of order manner. And the initiator will
handle this case.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Ia15f56c606e4f97af019f91fa1118cc9cac5daa7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5719
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Add FC LLD specific port placeholder in spdk_nvmf_fc_port.
As part of SPDK_FC_HW_PORT_INIT admin API, Let the LLD know about
the new fc_port.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: Ib9300176d294642a1825577a31ad999590f5f29d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5711
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Currently we are iterating over a hwqp connection list for every
IO command received. With high load of connections, this is causing
penalty. Use hash table for connection lookup based on connection ID
and also RPI identifier.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: I857e299722a0b72b25b0dbfe646d446ad98b7c76
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5688
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Factor out the common operation of nvme_ctrlr_depopulate_namespace_done()
and nvme_bdev_attach_bdev_to_ns() into a helper function nvme_bdev_ns_detach().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I8efa8bc2c2d455d0fd9e0865ff85fd265d14ee06
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5613
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Separate reference count of nvme_bdev_ctrlr between nvme_bdev_ctrlr
and nvme_bdev_ns.
Set ctrlr->ref to 1 when creating ctrlr, increment ctrlr->ref when
populating ns, decrement ctrlr->ref when destructing ctrlr or
when ns->ref becomes 0, and destruct ctrlr actually when ctrlr->ref is 0.
Set ns->ref to 1 when populating ns, increment ns->ref when
adding bdev to ns, decrement ns->ref when depopulating ns or removing
bdev from ns, and decrement ns->ctrlr->ref when ns->ref becomes 0.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I7810384d97a174d8f55d316e5cdf2a9ef4a11432
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5608
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
For further simplification, merge decrementing reference count of
nvme_bdev_ctrlr into nvme_bdev_ctrlr_destruct().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I604039c3f38a60b316ae465d4649e9eb11bfb6cc
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5573
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
destruct_poller had been used to destruct ctrlr after completing reset, but
we can remove destruct_poller and change reset processing to destruct ctrlr
after its completion by itself.
spdk_io_device_unregister() may fail spdk_for_each_channel(). Hence call
nvme_bdev_ctrlr_do_destruct() as the completion function of spdk_for_each_channel().
The first idea was to always run destruct_poller at nvme_bdev_ctrlr_destruct(),
but this patch will be simpler and more intuitive.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I43a400bdb67ab015d707fb9679693bd3d5bfb070
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5607
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
According to iSCSI 7143 spec 11.15.1 (3720 spec 10.15.1),
Rsph->response should be 0 if connection or session closed successfully.
The current code mistakenly compared cid provided by initiator with
inner conn->id parameter, which does not follow the spec.
Change-Id: I12dbb3471be5d49380c6b65bcdb67c57df11665f
Signed-off-by: ShadowMov <jinnian.hjn@alibaba-inc.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5731
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The purpose of this patch is to make spdk_bs_opts
for compatiblity issue.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I26d2a6bc644feede64d48890c7903f224b1fc306
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5681
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch includes the following work:
1 Add two fields in spdk_bdev_opts structure and make the
two fields configurable.
2 Update the unit test in bdev_ut.c
3 Revise the set_bdev_options rpc call and add the support
to use the two new fields.
Change-Id: Idd6073b3a3ffaba8161e3ffa9444a9e533e67f6d
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5664
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
It is optional to register i.e. most transports will not need to take
any action. It allows additional verification of ns/bdev capabilities
on transport layer before actual attachment to the subsystem.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I07d96b1d33c2d5433b951cb418ae1a89bf9caea5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5666
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With new spdk_nvmf_transport_listen function it should be possible to
add generic options without breaking API/ABI. For now it only delivers
json parameters which can be decoded on a transport specific layer.
This is similar to what was done for spdk_nvmf_transport_create and opts there.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: Iaf576248a0b10b408c4a3182785270be3e32ebe4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5570
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The following patches will need to update nvme_bdev_ns at
nvme_ctrlr_depopulate_namespace_done(). nvme_bdev_ctrlr can be
got from nvme_bdev_ns, and so this change will cause no issue.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I7cbfe0d936a3a757a8792fdf842e1228b2df05e6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4531
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Patch:
(d3d077cc) bdev: Solve the ABI compatibility issue related with spdk_bdev_opts
didn't include changes from day prior that added new code in bdev_ut:
(9697d84) test: add unit test for split IO
This patch fills in the gap in the UT.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ifc6c27d740b45e8135061d0ae86965afaafbe1b2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5640
Community-CI: Broadcom CI
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This member is useless now, all tcp requests
are tracked using state_queue member.
Change-Id: I4771ec163e44202a5d98d356d8935b6e518575ff
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5576
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This change prepares for the potential change in spdk-bdev_opts
in the future in order to maintain the ABI compatibility
Change-Id: I8ce24299173854c14c697bf7e28cf365c23f005f
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5597
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Per section 5.2 of the NVMe 1.3 spec:
"When the controller posts a completion queue entry for an outstanding
Asynchronous Event Request command and thus reports an asynchronous
event, subsequent events of that event type are automatically masked by
the controller until the host clears that event. An event is cleared by
reading the log page associated with that event using the Get Log Page
command (see section 5.14)."
Signed-off-by: Jiewei Ke <jiewei@smartx.com>
Change-Id: I0773ce1b704c2124db354fd19e0a8a19da48da54
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5462
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Add support to queue pending async events to avoid event lost if
multiple async events happen when there is no outstanding AER requests.
Pending async events will be consumes in FIFO order once any AER
requests are received.
Signed-off-by: Jiewei Ke <jiewei@smartx.com>
Change-Id: I545f0baa4ec2996e9e02ec12c176d639e3c0d55a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5117
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
At the same time the bdev supports optimal_io_boundary
and max_segment * max_size. Add a unit to test this
scenario.
Change-Id: Ied7c6cb9eefe0ab0c5a3469e9b184cb548a45f1b
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4928
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This unit test is for MAX_SIZE and MAX_SEGS
splitting IO.
Change-Id: I47278a9213986d8aa0e6db041b2795e595558498
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4820
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Mellanox Build Bot
When the backend device supports max segments and
max size, we may need to split the IO if the IO segment
size is bigger than max_size or iovcnt is bigger
than max_segments.
Add unit test for span split
Change-Id: If8e9c4f903b7def0ad7ddec7dc5aab8410498db5
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4602
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Delete connection code is scattered all over the place for
different scenarios. For FC-NVME2, we also need to have
ability to delete single connection at runtime. Cleanup delete
connection code and have a signle nvmf_fc_del_connection api that
can be used in all scenarios.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: I8d153681fd89dab8c4844b18f29c7e8f7caaa94d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5433
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
1) Create fc_req pool per fc connection based on SQ size. This gives more flexibity.
2) Remove create_max_aq_conns_test as it is not longer valid. We dont have any limit
on number of AQ connections based on the HW RQ size.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: I5c0b0d9ec9e9d63c7dccd76be7d6363a1f49c63e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5432
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
This patch is for packed ring live recovery.
First step is to track the packed ring descs.
This feature base on this QEMU patch:
https://patchwork.kernel.org/patch/11766697/
Change-Id: Id0ccb6fd12b3623cc367424f496b4ffc5323f390
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4126
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
As same as the last patch, change bdev_ocssd_from_disk_lba() to take
ocssd_ns as an additional parameter.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I2612df739137f687cf9aa8699c54885836742b88
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5537
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
As same as the last patch, change bdev_ocssd_to_disk_lba() to take
ocssd_ns as an additional parameter.
In unit tests, get ocssd_ns from not ocssd_bdev but nvme_bdev_ctrlr
because direct association between nvme_bdev and nvme_bdev_ns will be
removed when supporting ANA multipath.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I8e86b43bfe435fb2732e29e0fb6926d7572b29e2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5536
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch is used to support ABI compatibility related with
spdk_nvmf_transport_opts structure. We add a field opts_size in
spdk_nvmf_transport_opts and change the related two functions.
Fixes issue: 1485
Change-Id: Ifed3dc482bbc8fb54eb7089f7a1931718682f214
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5293
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
SPDK supports two latest DPDK LTS releases and DPDK 20.11
is out now.
Remove all functionality and checks for versions <= DPDK 19.11.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I9c354b7bc56d35a9ab04375f9f5255ca914d53e1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5344
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previous commit #ddba844, has wrong path in unittest.sh
and missing checks in unittest.sh and autotest.sh, that here was fixed.
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: Idc12719c0d427e3e6ec1a0e2c57e899508b0d7f5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5364
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
always be specified
Previously the parameter was optional and the size could be increased as
necesary. Now, it is required and a hard maximum. Later another function
could be added to dynamically increase or reduce this number if
necessary.
Change-Id: I3524ac737a6b592b4f6ce14ea48d3742a352c70f
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4996
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The purpose is to reduce the duplicated functions
in posix and uring implmentation.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Ia0568b2490d362e7e78fa59b3ca88a60313ba0bd
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5284
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
free_bdev() polls threads to push the bdev unregister forward.
get_device_stat_test called the free_bdev() within a callback,
which results in polling threads recursively.
Discovered while working on asynchronous registration for bdevs.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ib4f6f50c1542d11e98f8ba093710620cca016eb4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5211
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We want to add clang to autotest per patch, but lcov takes
considerable time to process clang coverage.
The test will be just building SPDK using clang.
Details: https://github.com/spdk/spdk/issues/1693
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: I085adb5498613222d36a0607b1fd260a2f4088b9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5169
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This change increases the coverage and makes the unit test more
realistic, and furthermore makes the following refactoring easier.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If8177b9cff888bf26e9a8e9830d4e915d264523f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5247
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
As part of FC transport destroy, FC LLD (Low level Driver) needs to
to do its cleanup which cannot be completed synchronously. So
allow transport destroy to be asynchronous.
FC transport code to use this functionality will be pushed shortly.
Signed-off-by: Naresh Gottumukkala <raju.gottumukkala@broadcom.com>
Change-Id: I104cf7d131e18199abdcf0651df261fe41d666ef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5180
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add an new function iscsi_portal_group_resume() and add an new parameter
pause to iscsi_portal_group_open(). They will be used in the following
patches to pause listening portals while target nodes are created at
start-up because Windows hosts do not retry login.
Pausing and resuming portal group is possible because we can unlisten
temporarily by simply not calling accept(). Any inbound connection
requests are queued to the backlog and once the backlog queue is full,
further inbound connection requests are simply dropped. If we restart
calling accept(), we will dequeue the backlog and be ready for more
connecitons.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If7403f91ebd729b47d98a23e589cba8b35569dc6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5088
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Zone append is an optional command in the Zoned Namespace Command Set.
Add a convenience function to check if the controller supports the zone
append command.
The ratified NVMe TP 4056 added a CSI field (in cdw14) to the Get Log Page
command. However, since there already exist two public functions to get a
log page (spdk_nvme_ctrlr_cmd_get_log_page() and
spdk_nvme_ctrlr_cmd_get_log_page_ext()), avoid creating a third one for
now, since nvme_ctrlr_get_zns_cmd_and_effects_log() itself can leverage
one of the existing public functions.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I99516dbac8db6714488b4d6cabe64c27f46d6153
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5078
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
POSIX defines PRId64/PRIu64/PRIx64 for printing 64-bit values in a
portable way. Replace a few references to %ld to remove the assumption
about the size of a long. Similarly, use %z with size_t arguments.
Where the value being printed is an unsigned 64-bit value, use PRIu64
instead of %ld.
Add a cast when comparing an enum to an integer value.
Add an explicit uint64_t cast to the definition of BLOCK_CNT to prevent
value truncation.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I093cffe7e79bc04eba012f4ffaf33062a642d062
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5137
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure
can be seen by removing 'LDFLAGS += -Wl,--gc-sections' in
spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: Iab76fbdebb13a9fda652418a0d75148d24c62378
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5082
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure
can be seen by removing 'LDFLAGS += -Wl,--gc-sections' in
spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Added stubs for use when configured with pmem.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I8944b8aaa90f27102ae6b030bfab89898194e5a4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5085
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure
can be seen by removing 'LDFLAGS += -Wl,--gc-sections' in
spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Move include of idxd/idxd.c after definition of movdir64b so that mock
function is used.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I760755122a1d3ca96f12b00b0040ae15471beafa
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5110
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure
can be seen by removing 'LDFLAGS += -Wl,--gc-sections' in
spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I3960ecc572090348c2ccabfc907b7abee89ed97f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5083
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure
can be seen by removing 'LDFLAGS += -Wl,--gc-sections' in
spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: Ic291ba22cbee121b5c75b80910378b456a217189
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5080
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure
can be seen by removing 'LDFLAGS += -Wl,--gc-sections' in
spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I63953b666e841942f51f9cc035c6a6521663079d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5084
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure
can be seen by removing 'LDFLAGS += -Wl,--gc-sections' in
spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I0a8606f9ec1743f7ca430f68c90b59f5699155b6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5081
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With some build environments (e.g. clang, see #1613) linking fails with
unresolved references. This is caused by the inclusion of 'unused code'
which is usually discarded by the linker. The 'unused code' contains
references to functions that have not been 'stubbed' out. The failure can
be seen by removing 'LDFLAGS += -Wl,--gc-sections' in spdk.unittest.mk
Resolved by adding stubs for missing references. These are never called
so return an arbtrary default value.
Part of a set of independent changes which
Fixes#1613
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I7bafbd2b414e1502d54f317d7b671798d564732c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5079
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
There are many duplicated codes about sending response for writing bool result.
That we need a function to do this.
Then we can reduce many codes.
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: Ic439111b1e9ca1013f8c657ab925f0c27a7be699
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5033
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Previously local boolean variable empty was used to destruct a
controller in delete_nvme_bdev_controller(). However, it was hard
to understand and did not work well with refactoring.
Using reference count is more sophisticated and works well, and hence
done in this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I59d0552c16653495fa55e9bfe4a2c0a316a204c3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4355
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Added asynchronous event notices for discovery log change
as per nvme fabrics spec 1.1. This allows a host with persistent
connection to discovery controller to automatically connect to any
new subsystem available to the host automatically.
According to nvme fabrics spec 1.1, if the connect command specifies a
non-zero keep alive timer value and the discovery controller does not
support asynchronous events then we need to return Connect Invalid.
Since SPDK does not implement this check instead added support
for asynchronous events in discovery controller.
Change-Id: I4cade5f7d24826ce97a2fa2b4ca688a1d728c1db
Signed-off-by: Madhu Adav MJ <madhu.adav@flipkart.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4870
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI
Section 7.9 of the NVMe spec says that all nqns must
start with "nqn.".
Fixes issue #1669.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I7fd0e6a0a397e831c4fa2377126b6b1e1b127d88
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5017
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
clang-9 is a bit more onerous on stubs required in
the unit test file. app_ut specifically needs
spdk_reactors_init and spdk_reactors_fini added.
Fixes issue #1613.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Iaa219829e933405ddb662f5b991204ef05b3bd75
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5016
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This fixes link issues with clang on some systems.
Fixes another part of issue #1613.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Icd51351b8e38043f267918b85e8ed1c3daab2db7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4860
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
If interrupt mode is set, related poller functions will be
registered to interrupt handler instead of poller.
interrupt_tgt can work as vhost-blk target to support VM.
Change-Id: I3a15f9a63532f44fe0d2f0cb69b0efdd72431d10
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4277
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This fixes#1423 where the completion loop never
breaks when the NVMe ctrlr is no longer present.
This condition can happen during a hot remove.
Signed-off-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Change-Id: Ia238c8aeae720832068de28ce4d34a9d233344fb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4831
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Vasuki Manikarnike <vasuki.manikarnike@hpe.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
It is possible that a single probe_ctx could be used
to probe multiple newly attached nvme controllers. If
one of those controllers is removed during this process,
the rest of the controllers do not get probed and can
even get stuck in a zombie state.
It is better to just continue with probing the rest of
the controllers.
Fixes issue #1611.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I4156ee8b50e8d52cfeee7224f210a58bb773e939
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4945
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Vasuki Manikarnike <vasuki.manikarnike@hpe.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
According to the SPEC we should support up to 8192 bytes
of ICD for admin and fabric commands. Transport configuration
parameter in_capsule_data_size is applied to all qpair types -
admin and IO. Also we allocate resources when we get a connection
request, so we don't know qpair type at this moment.
Create a list of buffer in TCP poll group to support ICD up
to 8192 bytes when configuration ICD is less than this value.
The number of elements in this pool is hardcoded, it is planned
to add a new configuration parameter later.
Fixes issue #1569
Change-Id: I8589e3e2ea95d515f5503c6de7c1ee40aaf7b6da
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4754
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
In TCP NVME initiator with zero copy enabled requests might be
completed asynchronously - out of qpair_process_completions
context. At the same time we calculate requests completed
asynchronously so that generic NVME layer can resubmit
queued requests after calling qpair_process_requests (or
poll_group_process_requests).
But there is a time gap between async request complete and
qpair_process_completions and the user can submit new IO
thereby decrease the number of free TCP requests. That means
that there might be less free requests than we excpected when
we try to resubmit queued requests.
The solution is change ERRLOG to DEBUG log since it is not a
fatal case.
Change-Id: If045ecd331cc6693e8ef450d8e15432dfa5d8812
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4859
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Move current scheduler to it's own module
and make use of new API.
Change-Id: I4928aed82603d51de01194c9650709e814f7f61b
Signed-off-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4054
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The tests did not use the legacy files anyway.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Icffedb7cc7a8574f0f801883b2d9655515cab687
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4855
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
And to eliminate an artificial constraint on # of user descriptors.
The main idea here was to move from a single ring that covered all
user descriptors to a pre-allocated ring per pre-allocated batch.
In addition, the other major change here is in how we poll for
completions. We used to poll the batch rings then the main ring.
Now when commands are prepared their completion address is added to
a per channel list and the poller simply runs through that list
not caring which ring the completion address belongs too. This
simplifies the completion logic considerably and will avoid
polling locations that can't potentially have a completion.
Some minor rework was included as well, mainly getting rid of the
ring_ctrl struct as it didn't serve much of a purpose anyway and
with how things are setup now its easier to read with all the
elements in the channel struct.
Also, a change that came in while this was WIP needed a few fixes
to function correctly. Addressed those and moved them to a
helper function so we have one point of control for xlations.
Added support for NOP in cases where a batch is submitted with
only 1 descriptor.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ie201b28118823100e908e0d1b08e7c10bb8fa9e7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3654
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
All options -c, --config and --json are valid, but have to
point to JSON configuration file.
Adjusted UT since JSON configs don't work with --wait-for-rpc.
Since this removes last reference to legacy INI configuration,
updated conf library to no longer mention the deprecation.
All uses of conf library are for explicit reason and not
related to SPDK event framework configuration.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ic9a702465982daf715ce1c2ab863c48584734611
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4752
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch removes callback function for subsystems to
present their options for legacy config.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I63076fc03eff45da5d57fab03501602922a20e3e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4749
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add two new helper functions, nvme_ctrlr_detach_async() and
nvme_ctrlr_detach_poll_async() to make the internal of
spdk_nvme_detach() asynchronous.
Use callback function to remove controller from the attached list after
completing shutdown and before freeing to avoid conflict between
attach and detach.
Update MOCKs in the corresponding unit test cases.
The next patch will add two public APIs spdk_nvme_detach_async()
and spdk_nvme_detach_poll_async() based on this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifbdfec2a1facde9354007c6248f280e245a36eed
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4416
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch removes legacy config support in iscsi subsystem.
All options through the legacy config are already reflected in JSON.
Following RPCs are corresponding to removed legacy config sections:
Initiator groups - iscsi_create_initiator_group and iscsi_initiator_group_*
Subsystem options - iscsi_set_options
Portal groups - iscsi_create_portal_group
Target node - iscsi_create_target_node and iscsi_target_node_*
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I11326a84d4d580b19db422b8522198eea5a5be0d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4747
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Replace all calls of spdk_bdev_create_bs_dev_from_desc() and
spdk_bdev_open_ext() by calls of spdk_bdev_create_bs_dev_ext()
including unit tests.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Idb9dc5a10f6e221c26e82e0194930cb7a2071dae
Change-Id: I61e577db9e26ef3e1c3e2e4093ad66922a178f34
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4723
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Change the first parameter of vbdev_lvs_create() from bdev pointer
to bdev name, and then remove spdk_bdev_get_by_name() from
rpc_bdev_lvol_create_lvolstore().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9b0e47f551657f6aa1235af37a8357b0af62d414
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4707
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This is a drop-in replacement. The following patches will remove
spdk_bdev_get_by_name() from the operation to create lvol store.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I31688cf98625f1d13012281d89f06d343e2f2cef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4705
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Remove the stub for spdk_bdev_open() and use the DEFINE_STUB_V macro
to the stub for spdk_bdev_close().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I84df06b4b73e1f5af5c2c8854f1613e8a413533b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4729
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Replace all spdk_bdev_open() calls by spdk_bdev_open_ext() calls
in the multiple SPDK threads cases of the unit tests for lib/bdev.c.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I65591f12f8737bb8a0c1256fa84c5b6dac481150
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4728
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Replace most spdk_bdev_open() calls by spdk_bdev_open_ext() calls
in the unit test for lib/bdev.c.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifbb8a7338b1d99808c96c87be1cfbee145b0d21f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4727
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch removes legacy config support in bdev layer.
All options through the legacy config are already reflected in JSON.
Removed configuration can be set via `bdev_set_options` and
`bdev_set_qos_limit` RPC.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I24c365625540659cad425268d2aa41e3bf279d5d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4645
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch removes legacy config support in blobfs library.
Mostly reverting patch:
(97f3104) blobfs: Add conf parse for blobfs.
CacheBufferShift option in legacy config is not tested in CI,
and never received corresponding RPC.
If required the RPC can always be added later on.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I54e39f069047a243b2186ae5ea225ed452180488
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4668
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The internal vhost library is used when DPDK's version
is older than 19.05 and the experiemntal vhost nvme
target.
For the CONFIG_INTERNAL_VHOST_LIB option, SPDK doesn't
enable this option by default over one year and CI
doesn't cover it either, so we may remove it with
this release.
As for the vhost-nvme target, since we are developing
a new vfio-user target solution, it's OK for us to remove
it now.
Change-Id: Ib2cce1db99cd09754307c2828b3187f2d4550304
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4562
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
After decoding a JSON object we had to free the parsed
strings one-by-one. Not anymore.
Change-Id: I819f1d533e397aa9babca58b5500c38ac01a963d
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2753
Reviewed-by: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
It's not needed. Add it to one of the UT where it
is needed though.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I06628184c22df68deffce3ca0561878569ccf3f4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4717
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There are more transport on the way and we don't want to add
all their various opts into the single, generic structure.
We'll pass the JSON structure to transports instead. Then
the transport code can custom pull from the JSON any param
it wants.
To complement that, transports will now also have their own
JSON config dump callback. This was only done in the generic
nvmf.c so far, with conditions for RDMA and TCP.
Change-Id: I33115a8d56cec829b1c51311a318e0333cc64920
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Signed-off-by: jiaqizho <jiaqi.zhou@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2761
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is just a drop-in replacement.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I018ef60648122aa672430bb62dc7b1a2e1cd5d7c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4648
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is a drop-in replacement. Update unit test together, and the
idea of the update was from the unit test for zone bdev module.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ia8d0644f42b9d0a0ad502eebbe3e414abd1de4cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4591
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
vbdev_crypto_claim() gets bdev name instead of bdev pointer
as a parameter, and open the corresponding base bdev first using
spdk_bdev_open_ext().
The purpose is to fix the race condition due to the time gap
between spdk_bdev_get_by_name() and spdk_bdev_open(). A bdev pointer
is valid only while the bdev is opened.
Resize event is not supported for now.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ia0e1ce2ce696f431bb26af94729931c3ffb9a9d0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4588
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
gcc version 10.1.1 20200619 releases/gcc-10.1.0-223-gf8e16e23d0
(Clear Linux OS for Intel Architecture)
Issue reports:
CC test/unit/lib/nvme/nvme_ns_cmd.c/nvme_ns_cmd_ut.o
bdev_ut.c: In function ‘bdev_io_alignment_with_boundary’:
bdev_ut.c:2146:2: error: ‘buf’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
2146 | free(buf);
| ^~~~~~~~~
bdev_ut.c: In function ‘bdev_io_alignment’:
bdev_ut.c:2008:2: error: ‘buf’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
2008 | free(buf);
| ^~~~~~~~~
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: I6d1bbf74b230b7bc51646454ddba0db4792f5900
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4693
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Search for md_page to be used as extent page started
from 0, which is completely valid md_page.
This page can be free when for example blob with id 0
was deleted and some other requested a new page for extent.
There are already existing blobs that have extents
pointing to 0, which means unallocated.
Unfortunetly it means 0 can never mean md page 0.
If that already occured for someone, this extent page was already
lost during blob/bs reload and nothing can be done.
With this in mind following assumptions are made for extent pages:
- 0 means unallocated extent page
- UINT32_MAX means we ran out of md pages, and should not be persisted
- [NEW] extent page can never occupy md page 0
That last one is new addition in this patch.
bs_allocate_cluster will now always try to find md page from 1 or higher.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ia17ce5bbca2fab4fb4487e4e263f3a0aa120bf17
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4314
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
When loading a blob and parsing its metadata,
the array of pages was not updated.
Serialization was unaffected, since the current pages
array is unused there.
Behavior was working correctly for first page,
but did not for any blob with more than one page.
Unfortunetly blob_persist_zero_pages() never zeroed out
the pages, neither blob_persist_zero_pages_cpl()
released the md pages.
Resulting in md pages being claimed even after blobs
deletion.
This patch now fills out the active pages array with
the appropriate page numbers from metadata.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I6ff1f4fe95684119d283c2471fdbbea464da8151
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4504
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch removes the call of spdk_bdev_get_by_name() from
create_compress_bdev() by calling spdk_bdev_open_ext() and then passing
bdev descriptor to _prepare_for_load_init().
vbdev_init_reduce() returns the return code of spdk_bdev_open_ext()
directly if it is error to process the ENODEV case correctly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ie80ce4104ceaa5726db976e33cd35352d5c91703
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4571
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
There is nothing left here, so remove it.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ib947d42bc577dbebb4650b1be885e05a80f8f8cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4541
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom CI
Add an new API spdk_nvmf_subsystem_add_ns_ext() to pass not bdev but
bdev_name to fix the race condition due to the time gap between
spdk_bdev_get_by_name() and spdk_bdev_open(). A pointer to a bdev is
valid only while the bdev is opened.
spdk_bdev_open() has been replaced by spdk_bdev_open_ext() but the
issue still existed.
Update the corresponding unit tests accordingly.
Then replace the internal of spdk_nvmf_subsystem_add_ns() by
spdk_nvmf_subsystem_add_ns_ext() call.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifcaa2121129ef22d5e61c9a8f7c640ff37a64485
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4485
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch removes the string from register component.
Removed are all instances in libs or hardcoded in apps.
Starting with this patch literal passed to register,
serves as name for the flag.
All instances of SPDK_LOG_* were replaced with just *
in lowercase.
No actual name change for flags occur in this patch.
Affected are SPDK_LOG_REGISTER_COMPONENT() and
SPDK_*LOG() macros.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I002b232fde57ecf9c6777726b181fc0341f1bb17
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4495
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Mellanox Build Bot
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI
This saves 2 bytes and allows it to pack nicely with the
changing state bool (which must remember separate for atomic
operations).
Change-Id: Ibb92ae3c74306e60385ae23d0aaf877f33a69095
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4553
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Pass not bdev but bdev_name to scsi_lun_construct() to fix the
race condition due to the time gap between spdk_bdev_get_by_name()
and spdk_bdev_open(). A pointer to a bdev is valid only while the
bdev is opened.
spdk_bdev_open() has been replaced recently by spdk_bdev_open_ext(),
but the issue still existed.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ic462422dbc2501c24907f56a36570fbb54fef65b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4482
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Use the same thread context to call both spdk_nvmf_tgt_create() and
spdk_nvmf_tgt_destroy(). This is required to ensure the accept poller
is registered and unregistered in the same thread context.
Signed-off-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Change-Id: I0637c7896ca7504412fbe673355f6904dd81a961
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4449
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add a new state in the SPDK NVMe state machine in order to fetch
I/O Command Set Specific Namespace data structures.
Right now there is only support for the Zoned Namespace Command Set
Specific Identify Namespace data structure.
The NVM Command Set Specific Identify Namespace data structure is
all zeroes right now, reserved for future use.
The Key Value Command Set Identify Namespace data structure is not
all zeroes, however, adding support for Key Value is outside the
scope of this patch.
The new NVME_CTRLR_STATE_IDENTIFY_NS_IOCS_SPECIFIC state is added
after the NVME_CTRLR_STATE_IDENTIFY_ID_DESCS state. This is because
we need to have fetched the identifiers in the desc list in order
to know which command set a namespace belongs to.
A slightly nicer design might have been to refactor the NVMe state
machine to first fetch the id desc list, then the identify namespace
struct, and finally the identify IOCS specific namespace struct.
However, since this would have required a lot of changes, it didn't
really seem justified.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I62cbc533c2c3eec1ccf0ba9b1c414d5a70919cff
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4368
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add a new state in the SPDK NVMe state machine in order to fetch
I/O Command Set Specific Controller data structures.
Right now there is only support for the Zoned Namespace Command Set
Specific Identify Controller data structure.
The NVM Command Set Specific Identify Controller data structure is
all zeroes right now, reserved for future use.
The Key Value Command Set Identify Controller data structure is also
all zeroes right now, reserved for future use.
The new NVME_CTRLR_STATE_IDENTIFY_IOCS_SPECIFIC state is added
after the NVME_CTRLR_STATE_IDENTIFY state. That way, if support for
the Zoned Namespace Command Set is enabled during probing, we will
fetch the Zoned Namespace Command Set Specific Identify Controller data
structure, regardless if any Zoned Namespaces are attached or not, and
no additional steps will be needed once a Zoned Namespace is attached.
Since we only have one command set to fetch, avoid creating
NVME_CTRLR_STATE_IDENTIFY_IOCS_SPECIFIC substates, although that will
probably be needed when support for another command set is added.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I95535b09b03b7ef2ee9a11eebdbd28aad66d65ba
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4367
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
A preparation step for enabling zero copy in NVMEoF TCP initiator.
Since nvme_tcp_qpair_process_completions doesn't process poll
group, we can't get asycn notification from kernel.
1. Add a qpair to poll group before we send icreq in order to be able
to process buffer reclaim notification.
2. Check if qpair is connected to a poll group and call
nvme_tcp_poll_group_process_completions instead of
nvme_tcp_qpair_process_completions when waiting for icresp
3. Add processing of poll group to nvme_wait_for_completion_timeout
and nvme_wait_for_completion_robust_lock since they are used to
process FABRIC_CONNECT command
Change-Id: I38d2d9496bca8d0cd72e44883df2df802e31a87d
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4208
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Currently, the scsi bdev only supports the hotremove event,
and the scsi library uses the deprecated `spdk_bdev_open` function.
In this patch, add the resize event support, so the upper layer
could do more actions, like vhost-scsi could notify the guest os.
For the scsi compatibility, add _ext suffix for some public api.
Change-Id: I3254d4570142893f953f7f42da31efb5a3685033
Signed-off-by: Li Feng <fengli@smartx.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4353
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add an internal API nvme_wait_for_completion_robust_mutex_lock_timeout()
and related internal APIs just call it with adjusting parameters.
nvme_wait_for_completion_robust_lock_timeout() will be usable for
the current use cases of nvme_wait_for_completion_robust_lock() and
future use cases.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I2b499643930256a39ebe279f56a399f20a7a2fde
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4217
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
We do not compile blob_ut on systems with Cunit version
that is too old. So modify unittest.sh for this case
specifically, so that users with an older Cunit version
can still run the rest of the unit tests.
Fixes issue #1601.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ifd226a47a2ff712ad1f14fd12e1cb796e44be6b5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4372
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Liang Yan <liang.z.yan@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
With the introduction of namespace types, the identify command has
gained an additional parameter: Command Set Identifier (CSI).
This parameter is similar to the existing parameters NSID and CNTID,
and is not used by all CNS values.
Most notably, the CSI parameter is not used for the existing CNS
values 00h (ID NS) and 01h (ID CTRL).
There are new CNS values, e.g. 05h (ID IOCS specific NS), and
06h (ID IOCS specific CTRL), which do take the new CSI parameter.
The new CNS values instead return Command Set Specific data structures,
which is basically an additional data structure. Therefore, the CNS
values 00h and 01h are very much still in use.
(Even the NVM Command Set has a Command Set Specific data structure,
even though all fields in that data structure are currently reserved.)
Since the CSI parameter is unused by all the existing calls to
nvme_ctrlr_cmd_identify() (since none of the calls send in a CNS value
that uses CSI), simply send in 0 for all existing calls.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: Ia2b2324393a0707152b2f8511f0a22ad4a12bd46
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4309
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
There are two different is_active() functions.
spdk_nvme_ctrlr_is_active_ns() which iterates through the active_ns_list,
and spdk_nvme_ns_is_active(), which simply checks the nsdata.
There is an event callback that refreshes active_ns_list when a relevant
events has occured.
In nvme_ns_construct(), nvme_ctrlr_identify_ns() has just been called,
so we know that nsdata is as fresh as possible.
Hence, there is no reason to iterate through a less fresh active_ns_list.
Since we know that the nvme_ctrlr_identify_ns() call was done through the
same controller, we also know that the active/inactive is from the
perspective of the correct controller, so that is not a reason to use the
less efficient is_active() function.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I185f59b53e16e70163e33a3909f4b55ebf631cc4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4293
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Since the command set identifier might be accessed at several
different states in the nvme state machine, cache it so that
we don't need to loop through the ns id desc list every time.
This is similar to how other identify fields are cached using
nvme_ns_set_identify_data().
None of the identifiers in the desc list (including the new CSI)
can change over the life time of a namespace, so caching them
should be safe.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: Ie06180a4b3750dfa1a42f47afe0f7f9e3ec04ba9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4266
Community-CI: Broadcom CI
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Use nvme_ns_construct()/nvme_ns_destruct() for each subtest.
This is what lib/nvme uses when creating/deleting namespaces,
so it makes sense to use the same functions in the unit test.
If we explicitly call memset(), we might hide real problems,
since e.g. nvme_ns_destruct() does not clear all struct members
in struct spdk_nvme_ns.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: Ia0ffce3d0a29088282e9fc8fc5413b98d1fe7c63
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4264
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
On clear linux the # was interpreted as bash comment.
The result was that no file was included and CU_VERSION
was undetected.
Removing the backslash before hash resolves it on clearlinux,
but breaks on fedora 31. Workaround in this patch portable
for both, as strange as it looks.
For future reference:
Fedora 32, Make 4.2.1, gcc 10.2.1, bash 5.0.17
Clearlinux, Make 4.3, gcc 10.1.1, bash 5.0.16
While here, added more specific string detection for
CU_VERSION. Before patch e7a86c42 only CUnit header was scanned,
now other output from CC is. This will prevent accidental
matches in the future.
Fixes#1562
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ia4aa9fcbc3ad810755cfecd745c5c1ecd2a70717
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4240
Community-CI: Broadcom CI
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The issue happens when SPDK RDMA initiator is connected to a remote
target and this target reports rather small (or zero) ICD and we try
to send several SGL descriptors.
Since SGL descriptors are located in ICD, we should check that their
total length fits into ICD. In other case sending such a command
will cause RDMA errors (local length error)
Change-Id: I8c0e8375dae799bc442ed2fab249cad2c4ccce51
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4131
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add an internal API nvmf_subsystem_set_ana_state() to change the
ANA state of the subsystem listener whose trid matches.
ANA optimized state, ANA non-optimized state, and ANA inaccessible
state are supported. ANA change state is not used and ANA persistent
loss state is not supported.
After changing the ANA state of the subsystem listener, on each poll
group, controllers, whose the subsystem listener match, send ANA
change notice.
Initiators query ANA log page anyway if they receive ANA change
notification. False positive notification should be avoided but is
acceptable.
To avoid any concurrency conflict, simply compare ctrlr->listener and
the passed listener.
It may be better to execute nvmf_subsystem_set_ana_state() on the
subsystem thread but currently the RPC thread adds and removes a
listener to and from the subsystem, respectively, and the subsystem
has been suspended while executing nvmf_subsystem_set_ana_state().
Hence we keep this as a future enhancement.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If1910b79dd33d904114e258ae2c5e868947cdc52
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4079
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
We still need to be able to explicitly set specific
bits in the cluster array during initialization and
loading (especially recovery), so we use a bit_array
during load, and then convert it to a bit_pool just
before calling the user's cmopletion callback.
This gives a roughly 300% improvement over baseline
on a benchmark which does continuous resize operations.
The benefit is primarily from saving the lowest free
bit rather than having to always start at bit 0. We
may be able to further improve this by saving extents
in the bit pool as well, although after this patch,
the benchmark shows other hot spots different from the
bit search.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Idb1d75d8348bc50560b1f42d49dbe4d79d024619
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3975
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add support for getting the Command Set Identifier for a given namespace.
The SPDK_NVME_CAP_CSS_IOCS feature can be implemented on top of an old NVMe
specification. If the feature is set, retrieve the NS ID Descriptor List
regardless of the NVMe specification version. The quirk is still respected.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I7b257115ecb0d813ba75201c0f48960c7070dcc9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4085
Community-CI: Broadcom CI
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This test repeatedly creates and deletes blobs to
confirm that the used_md_pages and used_clusters
bit arrays are managed properly. This test exposed
the bug reported in #1590 which has now been fixed.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-ID: If5d7b7f03cc2fb9daac928573c73430b74ea9a51
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4038
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
For I/O commands, block them if ANA state is inaccessible, persistent
loss, or change.
For Identify command, clear capacity field (nuse) to 0 if ANA state
is inaccessible or persistent loss.
For Get Features command, block features, error recovery, write
atomicity normal, reservation notification mask, and reservation
persistence if ANA state is inaccessible, persistent loss, or change.
For Get Log Page command, error information page does not return
any data yet, and hence there is no change.
For Set Features command, if ANA state is inaccessible or change,
block the command if NSID is 0xFFFFFFFF or if feature is error recovery,
write atomicity normal, reservation notification mask, or reservation
persistence, or if ANA state is persistent loss, block the command.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I15dd593227e451aa2247c53da42b6acad1757907
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4043
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Find the subsystem listener whose trid matches req->port->trid when
creating a controller, and store it in the controller.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iea343b8d8ae827b554df2245b67aed113469c592
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4010
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The loop here was counting the bytes in the cpus array,
but the lcores are represented by bits.
While here, add a unit test that exposes this bug and
demonstrates it is now fixed with this patch.
Fixes#1570.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I3a1fc48a8085254f41587e3b3d5d732154b90134
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3931
Community-CI: Mellanox Build Bot
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Currently when the uevent processing code finds a non-uio/vfio
uevent, it just stops its loops and returns. This means that if
there are a lot of non-uio/vfio uevents, the netlink socket buffer
can build up until its full because only one non-uio/vfio event
gets drained per spdk_nvme_probe() call (which may be very
infrequently).
So modify parse_event so that it does not indicate error when
a non-uio/vfio event is found.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ic8a40f71ee89d597ce46129eac889fe5b7ef5171
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3876
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The specification says it will return INVALID FIELD if the NS
is in inactive state.
Fix issue #1551.
Change-Id: I1b32f023ed665d410f4705e439068699e2b2f8de
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3860
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
We only create one spdk_blob object for a given blob, and just
increase the ref_count if it is opened multiple times. bs_open_blob
would do the lookup for existing opened blobs.
But if the blob is opened again, before the previous open operation
has completed, we would end up with two spdk_blob objects for the same
blob.
Solution is to do another lookup when the open operation completes.
If we find the blob, free the one we just finished opening and return
the existing one instead.
Also added unit test that failed on the existing code but passes now
with this patch.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Reported-by: Mike Cui
Change-Id: I00c3a913b413deddf06f0b63f7a669efb2b5658f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3855
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This allows for much more granular control over the timeout.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ib23de21e60eec4207c55320579699edf284f4e16
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3794
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
By the recent refactoring, we have no static size array for outstanding
R2Ts per connection. It looks that we do not have any critical reason
to prohibit us from making max outstanding R2Ts per connection configurable.
There are some use cases to use large write I/O intensively (e.g. 128KB).
Let such use cases change the value of max R2Ts per connection by their
responsibility to do performance tuning.
Maximum outstanding R2Ts per task are defined both for iSCSI target
and NVMe-TCP target but maximum outstanding R2Ts per connection is
unique for iSCSI target.
The next patch will add the corresponding iSCSI option.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4f6fd3c750a9a0a99bcf23064fe43a3389829aa9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3776
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For some use case that there is heavy large read I/O, the performance
bottleneck due to MAX_LARGE_DATAIN_PER_CONNECTION was reported.
The following assumes that all I/Os are large read.
Large read primary task whose I/O size is more than
SPDK_BDEV_LARGE_BUF_MAX_SIZE (=64KB) is split into multiple
read subtasks.
spdk_iscsi_globals::MaxQueueDepth limits maximum number of outstanding
read primary tasks, and MAX_LARGE_DATAIN_PER_CONNECTION (=64)
limits maximum number of outstanding read subtasks.
MAX_LARGE_DATAIN_PER_CONNECTION is also used to calculate PDU pool.
To remove the performance bottleneck, change the macro constant
MAX_LARGE_DATAIN_PER_CONNECTION to a global variable
spdk_iscsi_globals::MaxLargeDataInPerConnection.
We don't see any negative side effect if we set
spdk_iscsi_globals::MaxLargeDataInPerConnection to 64.
The use case that reported the performance issue will change the
value of spdk_iscsi_globals::MaxLargeDataInPerConnection by its own
responsibility.
The next patch will add the value of
spdk_iscsi_globals::MaxLargeDataInPerConnection to iSCSI options,
and make it configurable by JSON RPC.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifc30cdb8e00d50f4d3755ff399263cf5d0b681b6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3755
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
If the portal group map of the target has a redirect portal,
iscsi_tgt_node_is_moved() fills the buffer by the redirected address
and returns true.
iscsi_op_login_check_target() calls iscsi_tgt_node_is_redirected() before
calling iscsi_tgt_node_access() because login redirection can be
checked before any or after all security check.
If iscsi_tgt_node_is_redirected() returns true, notify login redirection
to the corresponding initiator.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4573a69c0a32eafcfe48080a033c135e127da321
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3221
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
In SPDK iSCSI target, portal group works almost as identifier of
portal.
To support iSCSI login redirection, we need to have two types of
portal groups, public and private portal groups.
We need portals of public portal groups to redirect to a portal in
a private portal groups at login via temporary login redirection
funciton, and we need to make SendTargets return only portals in
public portal groups.
To do these simply, we mark primary or secondary portal group expicitly
at its creation by this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iccf87a4b9dd1f4a8fbb857a399b8f2dbc7c0b3ab
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3491
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Previously we might have any possibility to need iaddr in
iscsi_send_tgts(), but it is highly unlikely now. Let's remove
the param iaddr from iscsi_send_tgts().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ide3405706b727a9d6ebaa92ed83509196ff675da
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3442
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The upcoming new feature, iSCSI login redirection will requests
connections whose portal group tag matches to logout asynchronously.
Hence add pg_tag to the second parameter of iscsi_conns_request_logout()
and iscsi_conns_request_logout() checks if conn->pg_tag is equal to
the passed pg_tag.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iaea37f28046396404c5b4faed01d748f2944288c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3160
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is part of a larger series enabling failover at the bdev
layer for NVMe.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ic5c128244699c1a47275145ca7e41aa5f1366259
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3044
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch paves the way for introducing a tailq containing
multiple alternative paths to the same controller.
Change-Id: I13d30c12b8e0ce38eae687f9e76740be1d11e4d1
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3259
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
RDMA target can't handle bidirectional xfer type, in debug build
it throws an assert in nvmf_rdma_setup_wr function. NVMF controller
performs checks od opcodes, but the failure happens before this
check. Add similar validation in TCP transport.
Change-Id: I14400b9c301295c0ae1d35a4330189d38aeee723
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3436
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This becomes a problem when the qpair is reconnected.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I6677b396cf766684a4891ffbee93aa3e4e83374d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3391
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The new abort functionality doesn't take custom admin cmd
handlers into account.
This commit allows setting a custom admin cmd handler
for abort that provides the ability to influence the
bdev lookup to which the abort is sent to.
Signed-off-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Change-Id: I3a66c6f863f5ee4d89cb2194dffdc6855945fa8a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3485
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
struct spdk_nvmf_request holds req_to_abort and so passing req_to_abort
separately is not really necessary now. The internal API
nvmf_ctrlr_abort_request() was added at the stage of prototyping.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9ef2467d6f92422f044650c62a0777b95c0fc1ab
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3488
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
This follows struct rte_pci_id which had class_id as well.
We'll need it to make some additional DPDK APIs public through
the env abstraction.
Change-Id: I794a6cd6b17e48daf53b48fa5abe3d3dcfeaa403
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3182
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There is no reason to continue processing these requests if the
qpair is not still active. We should complete them and free
any resources they are still holding.
Also, not doing so can cause issues with trying to access pointers
in the qpair after they are invalid. See issue #1460.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I6e570a576983dfedf726dc4a9a83316209403e00
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3451
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Call nvmf_ctrlr_abort_request() if the request whose CID matches
is found and its state is executing.
nvmf_rdma_qpair_abort_request() returns immediately if rc is
SPDK_NVMF_REQUEST_EXEC_STATUS_ASYNCHRONOUS, or calls
spdk_nvmf_request_complete() otherwise.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I1462a21db7270f3d63f8f293ad4be61d52e74da1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3011
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Call nvmf_ctrlr_abort_request() if the request whose CID matches
is found and its state is executing.
nvmf_tcp_qpair_abort_request() returns immediately if rc is
SPDK_NVMF_REQUEST_EXEC_STATUS_ASYNCHRONOUS or calls
spdk_nvmf_request_complete() otherwise.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I1abceecc211ee79d8ac18a82dc63b13d313a6f27
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3008
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
State machine is different among NVMe-oF transports and is
encapsulated to the transport neutral NVMe-oF controller and
NVMe-oF qpair.
To implement abort operation for each NVMe-oF transport,
add a function pointer qpair_abort_request to struct spdk_nvmf_transport_ops
and a stub nvmf_transport_qpair_abort_request() to encapsulate
which transport is used.
The following patches will implement qpair_abort_request for each
transport. Each qpair_abort_request() is responsible to call
spdk_nvmf_request_complete() for the abort request.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I2beac959ed428c5108cf33691226b7fae5cd24d6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3007
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
We have no particular requirement to keep both conn->outstanding_r2t_tasks
array and conn->active_r2t_tasks list now.
To improve readability and maintaineability, unify two into the latter,
conn->outstanding_r2t_tasks list. Update unit test accordingly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I25cf7cffbe39ac66e102eb3052340de6ef65c8f1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3115
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previously iscsi_del_transfer_task() dequeued the task only from
the array conn->outstanding_r2t_tasks[].
process_non_read_task_completion() had dequeued the task from
the tailq conn->active_r2t_tasks then.
However abort_transfer_task_in_task_mgmt_resp had not dequeued the
task from the tailq conn->active_r2t_tasks then.
This was an apparent bug, and is fixed here. Update unit tests
accordingly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I93f02b2fb670dcee4c32d61c264e3ad5b4f9f43e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3108
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Poller should return status > 0 when it did some work
(CPU was used for some time) marking its call as busy
CPU time.
Active pollers should return BUSY status only if they
did any meangful work besides checking some conditions
(e.g. processing requests, do some complicated operations).
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Id4636a0997489b129cecfe785592cc97b50992ba
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2164
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch is used to enable uring test in some VMs or machines
in the CI pool.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I75c2ad477f5f648289d8dbb344b75b2408d56a38
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3107
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
headers can be installed in different directories but `/usr/include`
Signed-off-by: Jörg Thalheim <joerg@thalheim.io>
Change-Id: Ibc4641813f6f1c904560dfe7d05cb9b40109cea7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3134
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The length of a keyed SGL data block is limited by 3 bytes.
Add a check to fail requests which length exceeds 3 bytes.
In other case we can send an incorrectly formed SGL request with
an invalid or zero length.
Fixes issue #1450
Change-Id: I77cdaff5fbf4be5754a3ac6008b8ccd532ac5905
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3056
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
As SPC4R31 5.9.3 "Exceptions to SPC-2 RESERVE and RELEASE behavior" says,
add a SPC2 RESERVE/RELEASE test case when PR is present.
Change-Id: Ibd7e703895cb910637677c6cb28b09e014976e9d
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2893
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add a test case for SPC2 RESERVE/RELEASE from 2 hosts.
Change-Id: I7b2a6352aa8a90a291f495f059de8920d6cbc11b
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2892
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Some OS(Windows and VMWARE esxi) will send SPC2 RESERVE/RELEASE
commands when formatting the filesystems, but in our previous
implementation of reservation feature, we didn't add such support,
in specification SPC3/4, they all include one section "Exceptions to
SPC-2 RESERVE and RELEASE behavior" feature for compatible support of
SCP2 RESERVE/RELEASE, so we add this support now.
Fix issue #1414.
Change-Id: I65d85ffb3b8f824b0ae4e130f53f01d95735d700
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2802
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This is part of a larger series enabling failover at the bdev
layer for NVMe.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I0d89e1afab8aeaa90237d0ba780d708154f6e3be
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2881
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Include completion operation into nvmf_qpair_abort() and rename
it by nvmf_qpair_abort_aer() for clarification. Update unit test
accordingly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I763cc7d24b979e27e8775f4e69730466a2351bdf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2712
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Cache size of mempool is not based on SPDK thread but DPDK thread,
i.e. CPU core. So replace spdk_thread_get_count() by
spdk_env_get_core_count() to determine cache size of mempool in
spdk_bdev_initialize().
Besides, allocate and free stub cores at the corresponding unit tests.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Icc4deae84c74820af4de61e991fa3f8683add058
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2767
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Using not FAILED but ABORTED for the completion status of the I/Os
aborted by reset will be reasonable and is done in this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I8c8181dd33453a330888cffa93505e6fc462f278
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2708
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The last patch ensures that the parent I/O terminate with failure
before continuing splitting process if one of child I/O failed.
This simplifies abort operation for I/O splitting.
Then we can use bdev_abort() and bdev_abort_io() nestedly.
Add necessary unit test together.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I562bb6675f1fa380bc53dbe369138317ead66fe0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2235
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Previously, bdev_io_split_done() had continued splitting process
even if the status became failed. To abort split I/O, this patch
changes bdev_io_split_done() to terminate with failure before
continuing splitting process if the status became failed. Add
necessary unit test together.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifd1ea49c22523e8c06fb45ebdcb2c84a57afd2ef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2234
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is a preparation to abort split I/Os. To abort any I/O by
bio_cb_arg, they have to be managed by the submitted I/O list.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9459d9d2d3511aad0325dcc20d88610444a4ea04
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2231
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
When the target I/O is controlled by QoS, the abort request is
submitted on the same channel that the target I/O is submitted.
By using this, add a helper function bdev_abort_queued_io(), and
change _bdev_io_submit() to call bdev_abort_queued_io(), and
call _bdev_io_complete_in_submit() with success if bdev_abort_queued_io()
returned true when QoS is enabled on the corresponding channel.
Add necessary unit test together.
Update unit test accordingly, especially, update stub_submit_request()
to abort the matched I/O, update io_during_io_done() because we need to
know not boolean but the exact completion status now, and update
basic_qos() to reset the rate limit to test the abort I/O feature.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I16ca21e7c32cabfdce5d0e5c27a8af8bb00f11c5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2230
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Add spdk_bdev_abort function as a new public API.
This goes all the way down to the bdev driver module and attempts to
abort all I/Os which has bio_cb_arg as its callback argument.
We can separate when only a single I/O has bio_cb_arg and when multiple
I/Os have bio_cb_arg, but unify both by using parent - children I/O
relationship. To avoid confusion, return matched_ios by _bdev_abort() and
store it into split_outstanding by the caller.
Exclude any I/O submitted after this abort command because the same cb_arg
may be used by all I/Os and abort may never complete.
bdev_io needs to have both bio_cb_arg and bio_to_abort because bio_cb_arg
is used to continue abort processing when it is stopped due to the capacity
of bdev_io pool, and bio_to_abort is used to pass it to the underlying
bdev module at submission. Parent I/O is not submitted directly, and is
only used in the generic bdev layer, and parent I/O's bdev_io uses bio_cb_arg.
Hence add bio_cb_arg to bdev structure and add bio_to_abort to abort structure.
In the meantime of abort operation, target I/Os may be completed. Hence
check if the target I/O still exists at completion, and set the completion
status to false only if it still exists.
Upon completion of this, i.e., this returned zero, the status
SPDK_BDEV_IO_STATUS_SUCCESS indicates all I/Os were successfully aborted,
or the status SPDK_BDEV_IO_STATUS_FAILED indicates any I/O was failed to
abort by any reason.
spdk_bdev_abort() does not support aborting abort or reset request
due to the complexity for now.
Following patches will support I/O split case.
Add unit tests together to cover the basic paths.
Besides, ABI compatibility check required us to bump up SO version of
a few libraries or modules. Bump up SO version of blob bdev module simply
because it does not have any out-of-tree consumer, and suppress bumping
up SO version of lvol library because the affected struct spdk_lvol
is not part of public APIs.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I515da688503557615d491bf0bfb36322ce37df08
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2014
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is used to make spdk_nvme_connect can support
the old library for compatibility.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I49d92fb473c3cbabd8e1240785b920480202eee9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1998
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Having that transport can decide about particular ctrlr attributes not
globally but per ctrlr.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: Ia3fb0d4e576cb9f8ce6df75f775e2fd5727d7f48
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2757
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tracing functions introduce performance overhead
so by default keep them only in debug builds.
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Change-Id: I08e0a139c3efa87b0f46b7e7a026b0676f3e8634
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1924
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Community-CI: Mellanox Build Bot
I missed a few files in this library the first time.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I2ad55355e6348eaa10384a148dd45deb9f68fc2b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2442
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Remove inclusion of spdk/event.h and spdk_internal/event.h from
SPDK nvmf library. Their dependency had been removed.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibc6c52ab41555d9b29afc3e16c1c3fd0bf5fc63a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2687
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
iSCSI library still needs to include SPDK event library only for
shared memory ID to allocate shared memory for iSCSI top application.
We will move the code to module library separately later but remove
all other inclusion of SPDK event library in this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I21d77b9cc00c6a1f512546a6a0202c8fa5623bed
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2686
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The UT can test the received aer reqs number and
check if the reqs are continuous.
Change-Id: Ifa1cb9dd4cdae5526fc80fe6c1b504ad9873d0f8
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2549
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add the AER events in nvmf target from one to four.
Change-Id: Ie31988b49d68bdbc28ab2e09c783e681d3017e2b
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2548
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This helps ensure thread safety on creation of the
netlink socket, when probe is called from multiple
threads at once. It is also a lot more clean - we just
create it once, rather than checking every time probe
is called to see if it has to be created.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I528cedc3ff44de6ea8ecaf6d2389226502ba408e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2681
Community-CI: Broadcom CI
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This reverts commit 79215d80c1.
Reason: Find the bugs while using batched. For example, if
we fetch 3 CQEs, A, B, C and put it in a cqes[] array.
Then we leverage io uring cqe seen to handle, Then we handle the
CQE A, then invokes the call back related with A. In A's call back,
it may also call the reap function (sock_uring_group_reap),
then the CQEs will be handled again. Thus the CQEs B and C can be already
handled. Then we will handle B or C again, then it triggers the error.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I67ece3b24e677b88d66d08722b00539693b42e1e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2543
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
I found this flag weird while debugging a lvol with
thin provisioned Blob, so make it consistent with it's Blob.
Signed-off-by: Sochin Jiang <jiangxiaoqing.sochin@bytedance.com>
Change-Id: Iae555020d5781dfcf4d4f072a47e9573d35b8705
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2435
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
remove only the spdk_ prefix from static functions in
the above libraries.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I59ce032c3312fa73f30c133fd62e603c1eee2859
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2365
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch adds use of RDMA provider API to NVMEoF initiator.
Makefiles have been updated with new RDMA lib dependency
Change-Id: Ieaefeb12ee9681d3db2b618c5cf0c54dc52230af
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1657
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch updates NVMF target to use RDMA provider API
to create and destroy qpairs.
Makefiles have been updated with new dependency on RDMA lib
Change-Id: Iae35aea601380f8d1a6453a7fd6115f781e126f5
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1656
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
In current implementation, lib/vhost assumes that it always runs
together with lib/event, and would call lib/event's functions in
vhost.c. This is not necessary and make program unable to
create/destroy vhost module without init/fini the whole spdk env. It
would cause problems when program runs with vhost and other spdk
components together.
In this patch, we remove the dependency of lib/vhost on lib/event by
adding a global vairable g_vhost_core_mask so that it could handle
core mask by itself.
Signed-off-by: Kyle Zhang <kyle@smartx.com>
Change-Id: I38ceb92ac39b6980955346fda41e968aaead863d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1204
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
cache_free_buffers() was only used in the file deletion and unload, and
the file is also freed after that, so here we combine the cache free and
file free together and do the cache free in the cache thread.
Change-Id: I57e9a27c9a6467bcf6c85cd277db3b57e06c98e5
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1795
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Also poll thread in the UT to cover the thread context switch.
Change-Id: I3dc765b66aa707c36eb3913b3e0d2c1c3986e282
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1793
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This file isn't exclusive to the nvme lib. As such, it shouldn't
use the internal SPDK_LOG_NVME flag.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ib6d239ad2e45e58fb97a5ea70b01ce72afa938c0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2246
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
There were multiple ways to check if particular UT should be executed.
This script unifies those.
To allow executing unittest.sh as standalone script,
verifying config.h flags was chosen.
FTL is an exception, as it always compiles if built on Linux.
Same condition was kept to execute the UT.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I83b3a58d4574154166af6763e7d1c38d75b8475d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2019
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
NVMe spec defines "Keep Alive Timer" feature ID as optional and there
are targets that do not support this. SPDK fails to connect to such
targets.
This patch allows Get Feature "Keep Alive" target to fail with
INVALID_FIELD status. In this case we just continue with keep alive
timer value stored in controller opts structure. This value is already
communicated to target in CONNECT command.
Fixes#1328
Signed-off-by: Evgeniy Kochetov <evgeniik@mellanox.com>
Change-Id: I52e7ea3cb66073ce6cc168a169989bd179041618
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1625
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Blobid and md_page is claimed as first step of blob creation.
If blob creation failed, both should returned to be used by
other blobs.
This caused multiple reports of:
"Metadata page 1 crc mismatch"
when loading blobstore due to md_pages not actually containing
the written out md pages.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I495452c578d879f749281cebf8975eb2c1c7f79a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2057
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
reduce library uses unlink, but the unit tests need to
override it in a specific way.
But linking unit tests with LTO requires the wrapper
definitions be in objects/libraries listed *after*
the object/library that refers to it. So we need to
make the unlink wrapper somewhat generic. We do this
by exporting a string and callback function that the
user can set to enable a user-defined function to be
called when unlink() is called with a specific file
name.
Also revert 3ef6d06 as part of this patch, since we
no longer require the workaround that it implemented.
Fixes issue #1357.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I1ee4c424ad31fe7d91d7b524ed47aedd279e5b5c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1948
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Purpose: This can improve the performance.
Change-Id: I3f5526ab8716cb0771b5e193afa9a0dbffec5cc0
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1929
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Virtual controller capabilities can be overridden on transport
specific layer. The current behavior shall be preserved.
This can be useful to limit or extend the default based on transport
type.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I754f0d957a46f219adc1e55f792e79c7546ddb43
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1274
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Purpose: To set the priority of the NVMe-oF connection especially
for TCP connection.
For example, the previous example can be:
trtype:TCP adrfam:IPv4 traddr:10.67.110.181 trsvcid:4420
With the change, it could be:
trtype:TCP adrfam:IPv4 traddr:10.67.110.181 trsvcid:4420 priority:2
The priority is optional. We try to change
spdk_nvme_transport_id but not in spdk_nvme_ctrlr_opts since
the opts in spdk_nvme_ctrlr_opts will reflect in every nvme ctrlr,
this is short of flexibility.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Change-Id: I1ba364c714a95f2dbeab2b3fcc832b0222b48a15
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1875
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Purpose: This is used to make users can specify
some options on the socket, e.g., the different priority for the socket.
While creating sockets, the priority needs to be set before connect()
and listen system calls, so better to add one parameter in spdk_sock_opts
which can contain options (e.g., priority) in spdk_sock_listen_ext and
spdk_sock_connect_ext functions.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Change-Id: I406238e9da7abd69f937b7072535a19124ed0169
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1874
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
idxd support is disabled by default right now due to being
experimental. Running unittest.sh would cause failure in such case.
With this patch idxd_ut only runs when it was compiled in.
Verifying if the UT was executed is done in post_processing.py,
by verifying every 'run_test' was executed.
Meaning that CI makes sure it is executed.
resolves#1369
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Iafbc84839aa9dc62ead8821da8b860e1741e3624
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2012
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Last and only usage of struct lvol_task was removed in
previous patch.
Since it is no longer used, remove the structure itself.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I3612106de2ab3a9197245de078c73c53beeff443
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1971
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
There is no point in setting this value on submission
and changing it on callback.
Since it is based on blob bserrno.
lvol_task is removed in next patch.
This change was motivated by lvol_op_comp() accessing
the task->status pointer on hot path for I/O.
There is no need to do so, so just pass status.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I17461fcf355f771f4de4e6d5ec1900d5042bd3d5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1804
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The UT stubs weren't calling the assigned callbacks
and some weren't assering the passed values.
This will come in handy in next patch.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I86eec58a28e40a93ff06b7e7c715c17d25e28818
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1970
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
More tests will follow in later patches.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I6c45b94cc17219acfae863c774fc7dbc33625c85
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1782
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This makes more sense within the context of the nvme driver and
helps us avoid the awkward situation of getting a failed_qp callback
on a qpair that simply hasn't been connected.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ibac83c87c514ddcf7bd360af10fab462ae011112
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1734
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The qpair states should be maintained at the generic level.
Always going through the transport disconnect function is
one step in that direction.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I019b2b4a14fe192eff5293f918d633dde2c5400a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1851
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This variable really indicates when a qpair is
no longer connected. So NVME_QPAIR_DISCONNECTED is
actually much more accurate.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ia480d94f795bb0d8f5b4eff9f2857d6fe8ea1b34
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1850
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This should help reduce confusion within libraries about
which APIs are public and which are private.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I7755081b016f269d4761d8cc2ce4bac2835c077d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1703
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Also, increment the library version since some non-public symbols have been removed.
Please note, SPDK_LOG_BLOBFS is included in the map file because it is used by the
blobfs_bdev module.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ib05c0b6630951d97b1a5b2931746471eeb9d9630
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1702
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Fix the following warning by allocating status dynamically.
In function ‘nvme_completion_poll_cb’,
inlined from ‘test_nvme_completion_poll_cb’ at nvme_ut.c:546:2:
/var/jenkins/workspace/unittest-nightly-autotest/spdk/lib/nvme/nvme.c:92:3:
warning: attempt to free a non-heap object ‘status’ [-Wfree-nonheap-object]
92 | free(status);
| ^
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I321b88414f431c8c18617d3ee882b8ab851a70fa
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1940
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Since the related feature is already contained in
spdk_sock_listen and spdk_sock_connect functions,
we no longer need this function.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I1eafff0d139fa266a355fbee2bf0fc3947db69fc
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1876
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
As other small change, function iscsi_conn_pdu_generic_complete()
had been declared in conn.h but defined in iscsi.c. Move the
definition of it to iscsi.c.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I1bd796288036f78a7cba8a1c0af93bd6bc19e9cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1890
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
The following patch will remove the "spdk_" prefix from iSCSI
internal APIs. The iSCSI global data g_spdk_iscsi is also local in
SPDK iSCSI library. Hence rename it by g_iscsi for consistency.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If35e9d58b1388fd725a505ee9be870e414c37ba5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1831
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Instead of creating an allocator where the driver manages the space,
now, since using the CMB for queues and data has already been
disallowed, just create functions to map and unmap the entire CMB.
The user can manage the space.
Change-Id: I023994deda3b517e14d2ba464c7375bf22b58456
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/785
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Remove spdk_ prefix from the name of internal APIs.
Add single underscore as the prefix of the function name to the
private functions if we see any conflict as a result of this change.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If0eabffbdb750db02866c1aa2b29b0c89fab1040
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1824
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Both for SCSI IO task and management task, append and execute
operations bad bbeen separated into different functions.
Append operation was for LUN reset, and separating into two different
functions was for clarification and readability.
LUN reset is sufficiently stable now.
Merging append and execute SCSI task into a single function is good
as API and enables us to do optimization.
For SCSI management task, merge spdk_scsi_lun_append_mgmt_task into
spdk_scsi_lun_execute_mgmt_task() simply.
For SCSI IO task, merge spdk_scsi_lun_append_task into
spdk_scsi_lun_execute_task() and do a small optimization.
The refined spdk_scsi_lun_execute_task() adds the IO task to the
pending list if there is any pending management task, executes all
existing penging IO tasks first and then the IO task if there is any
pending IO task, or executes the IO task directly otherwise.
Update unit test accordingly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I26ffc4f4f62747d8cdecb90690f26cd58a9c17f7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1817
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is a preparation to the following patches to optimize task
submission and remove the spdk_prefix from internal or private
functions.
To avoid using double underscores as the prefix of the function name,
separate pending task check and outstanding task check into
different functions.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ieda54507bf4c781b60fa05d03cd32ca25948e430
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1826
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This unit test shows how the guest and host handle
the shared packed vring.
Change-Id: I4d02a22a225a7945bfe4a2691d917adae86661d6
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/828
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
When the size of input buffer is larger than 16 and not divisible
by 16, the final line will keep part of the characters of the last
line. For example, if I want to dump "spdk dump 16 more chars",the
output is:
00000000 "hexadecimal" spdk dump 16 mor
00000010 "hexadecimal" e charsmp 16 mor
But the correct should be:
00000000 "hexadecimal" spdk dump 16 mor
00000010 "hexadecimal" e chars
Signed-off-by: Richael Zhuang <richael.zhuang@arm.com>
Change-Id: Iaf3f33c5ce68920ada83c59277f89a547e8030d7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1739
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We should be giving completions for all requests when we destroy a qpair.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I802f5120f2e8289aa825872f8085ac21b5fce0f3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1756
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
NVMe ctrlr init state machine shall be async whenever possible so it
is not blocking other code from processing. It can result in deadlock
when cmd producer and consumer are sharing the same thread.
This patch is making identify active ns async by introducing new
state to wait for completions.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I346d35bab4733d3941e023602854fdd5b1ef23b5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1463
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom CI
It is a prework for changes related to ctrlr init state machine.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: If289580f65ae27468b659a7ea07a4e4298876e77
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1489
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom CI
Lack of this initialization cause compilation error on release builds.
bdev_raid_ut.c: In function ‘test_multi_raid_with_io’:
bdev_raid_ut.c:2007:3: error: ‘ch_ctx’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
2007 | verify_io(bdev_io, g_max_base_drives, ch_ctx, pbdev,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2008 | g_child_io_status_flag);
| ~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I2221aa1d78d640439d5876a781a0d173a370e2a7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1626
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch creates a test case to simulate nested I/O channels by
generic bdev layer and bdev modules. The nested level of I/O
channels is two at a maximum now but the nested level of the test
case is three.
Besides, any poller registered on the nested I/O channel is not
visible to the upper layer. So include such pollers into the test
case.
By combining thread termination, test the fix for the github issue
is correct.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6a04d753e462cdaba7364678b5118c45b09708ca
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1390
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI
Set 5 seconds timeout to wait until exiting thread is exited into
spdk_thread_poll(). After the timeout, collect error log and then
move the thread to exited forcefully.
Add necessary unit test case accordingly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ied8f58a2023a3bbe098530810fd3288bef93c3e7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1644
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Extract _spdk_thread_exit() from spdk_thread_exit() and
_spdk_thread_poll() calls _spdk_thread_exit() if the thread is in
the exiting state. spdk_thread_exit() changes to move the state to
the exiting state. The spdk_thread_poll() loop will end after the
thread moves to the exited state because the caller of
spdk_thread_poll() will check if the thread is in the exited state,
and break the loop if true.
If the user does not call spdk_thread_exit() explicitly, the reactor
has to terminate all existing threads at its shutdown. In this case,
multiple threads may have some dependency to release I/O channels or
unregister pollers. So the reactor has the large two loops, the first
loop calls spdk_thread_exit() on all threads, the second loop calls
spdk_thread_destroy() if exited or spdk_thread_poll() otherwise for
each thread until all threads are destroyed.
Besides, change the return value of spdk_thread_exit() to return
always 0. Keep it for ABI compatibility. Change ERRLOG to INFOLOG
for _spdk_thread_exit() because it is called repeatedly now. Remove
the check of I/O reference count from _spdk_thread_exit() because
_free_thread() cannot free I/O channel. Refine the unit test
accordingly.
Fixes issue #1288.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iee5fb984a96bfac53110fe991dd994ded31dffa4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1423
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Compiling with warning:
nvme_poll_group_ut.c: In function ‘test_spdk_nvme_poll_group_add_remove’:
nvme_poll_group_ut.c:268:8: warning: ‘tgroup’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
qpair = STAILQ_FIRST(&tgroup->active_qpairs);
tgroup may can't be initialized as:
if (tmp_tgroup->transport == &t1) {
tgroup = tmp_tgroup;
} else {
CU_ASSERT(STAILQ_EMPTY(&tmp_tgroup->active_qpairs));
}
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: Id915e651f73ca3814a7e8d3f95c8793b8b880990
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1738
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Following patches will require thread termination so that thread_exit()
will move thread to exiting, thread_poll() will move thread from
exiting to exited, thread_is_exited() will detect the threadis exited,
and then call thread_destroy().
So change all places as a preparation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6b2e8aee5ed7cd160a88b4c9aaed7d90bd9dac07
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1640
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previously the caller had to check if thread is not exited when
it calls spdk_thread_exit().
Subsequent patches will change return type of spdk_thread_exit()
to void, and so include the check int spdk_thread_exit() in this
patch.
If spdk_thread_exit() is called when the thread is already exited,
collect INFOLOG and return normally.
This will make the next patch a little easier.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I8b94261575e770485b33c0b37e76e770b77b417c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1639
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Following the idea of thread CPU stats, add reactor CPU stats.
Reactor CPU stats accumulates run time of spdk_thread_poll() calls
to idle TSC or busy TSC according to their return codes.
Add necessary unit tests.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I1a1391e79d74387c68f1651a61c8900e4c6faf66
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1501
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Currently nvme_completion_poll_status object is allocated using
malloc, so it may cotnain some garbage. In some scenarious
nvme_completion_poll_cb can be triggered before we enter
spdk_nvme_wait_for_completion_*. In that case status object
will be freed by nvme_completion_poll_cb if it contains a
garbage in `timed_out` field. Later spdk_nvme_wait_for_completion
will work with already freed memory.
Fix - allocate nvme_completion_poll_status object using
calloc and explicitly zerofy it before usage
Fixes#1292
Change-Id: Iac39653a6cd102471de16e65814f0760bbeda7d9
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1373
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Use SPDK thread library in unit tests for compress bdev. This will
enable us to write unit tests for refactoring.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iac3867cca460b998c9b3953aae5241ffddc3168b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1451
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
CUnit provides a helper macro CU_ADD_TEST() that
simplifies usage of CU_add_test() function.
Test name no longer needs to be provided,
as it will be inherited from function name.
This is a follow up to
https://review.spdk.io/gerrit/c/spdk/spdk/+/931
Change-Id: I8078f02e08b14f12328ae022d7090ba13fbd64e4
Signed-off-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1239
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This patch changes the way that unittests initialize.
The new way is shorter and simpler.
It assumes that error during initialization is a fatal error,
but in our cases it always is.
This patch is a followp up to
https://review.spdk.io/gerrit/c/spdk/spdk/+/930
lvol_ut.c is the only test that skipped because
it runs same tests multiple times which is not allowed
by new method.
Change-Id: I0baf7ad09a35d5fca2dc4a03b4453c12c14f38a7
Signed-off-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1238
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Previously the SPDK NVMe driver always set PSDT to 01b for hardware SGLs
which is aligned to the Linux NVMe driver, for this case the metadata length
is not required when filling the NVMe command fields. There is no alignment
nor granularity requirement for Data Blocks for PSDT 01b case. And if the
drive reported that it needs dword alignment with SGL, for this case, when
using spearate metadata, it needs a length parameter to fill the SGL descriptor.
Change-Id: I56ffaada775fe66de7637dae15b509ee9556e80a
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1351
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Currently SPDK rejects Connect command when subsystem is not active.
This change allows to queue Connect command and execute it when
the subsystem goes back to active state. To queue the command we
should know subsystem_poll_group, in current implementation
this poll_group is known only when controller is already created.
To get the poll_group for Connect command we can retrive subsystem
subnqn, find subsystem and get poll_group by subsystem->id.
Increment subsystem_poll_group->io_outstanding even for Connect
cmd in order to prevent subsystem change state during the
connection process. Update spdk_nvmf_request_complete -
decrement io_outstanding for Connect cmd.
Fixes#1256
Change-Id: I724abb911696d7234a9c9d27458eba24739b26fd
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1273
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This unittest uses CU_add_suite_with_setup_and_teardown()
which was added in CUnit 2.1-3 released over 5 years ago.
This is the most commonly packaged version of CUnit on
not EOL'd distributions.
Unfortunetly there is incorrectly created package on CentOS7.
CUnit-devel-2.1.3-8.el7.x86_64.rpm despite its name
contains CUnit 2.1-2.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I5ebf9973b1f3df9ff6cc1f0dc61dcf691096605e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1530
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This kind of changes are now done through out the UTs in SPDK.
Patch here just adds them here as well.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I66fc06bbea038e328ba27bdea58b6e6479eee122
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1487
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
lvs_load, lvols_load and lvol_open were already added to the suite.
Commit 2f22884 mistakenly added those three when adding lvol_refcnt.
To remove those UT actually fixes earlier in the series were required,
as incorrect errnos were checked before and this specific order of
UTs set the right errno between them.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I7188be49171b6254146c6d144f9a54a689151b60
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1486
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Simply some of the functions can be replaced with the stub
defines, so they were.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I3095855c02c605fe0d66ee720a5025cdd8933873
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1485
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
There are three types of callbacks in lvol library:
- void(cb_arg,lvs,errno)
- void(cb_arg,lvol,errno)
- void(cb_arg,errno)
First two are used in cases where result of operation is
either lvs or lvol.
Last one is used for any operation that does not produce
either.
There is no need to keep more than one callback function
for last one, since they all are doing the same thing.
lvol_op_complete(), lvol_store_op_complete(), close_cb() and
destroy_cb() are now replaced with op_complete().
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Idd8fcf327ef56ad7d27e2e31cad9ddc44c80e5c8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1484
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There were two variables (g_lvserrno and g_lvolerrno) to
assign and check after operations.
This caused issues when developer mistakenly created callback
that assigns one and then checks the other.
This UT is ran to completion each time and only single operation
is done at once. There is no need to account for both.
This patch removes g_lvolerrno.
Next one will simplify callbacks.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I7d16b1913c13de56e1df2f5e36db11f15430979b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1483
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This file is not included in any other test files and it isn't compiled.
It appears to be a remnant of when we had distinct vhost_blk and vhost_scsi
unit tests.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I0b29d9e601f9d86b51cf8ba52ec5dc96bd02eef9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1310
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
We only set the flag to false when the controller reports SGL supported
and can use byte contiguous buffer. Also check the data block's alignment
for hardware SGL.
Change-Id: Id936c49823963000d0543fc95fbb6edba3118feb
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1352
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Update spdk_thread_poll() to count SPDK thread stats correctly on multiple
SPDK threads per reactor configuration.
spdk_thread_poll() gets start time and reads TSC at end as end time,
and then gets delta between them as run time. Run time is added to idle
time or busy time according to the result of polling.
Reactor overhead is included into the next thread which calls
spdk_thread_poll() now.
spdk_thread_poll() saves the end time to the current thread to use it
as the start time of the next thread.
Unit test framework for this patch and the next patch need to access
thread->tsc_last. In the next patch, reactor will use the end time of
the current thread to the start time of the next thread in reactor_run()
to realize the idea.
Hence add an new API spdk_thread_get_last_tsc(). The corresponding
variable is named as tsc_last and it is good and is aligned with
DPDK (DPDK has used tsc_start and tsc_end as variable name). But
last_tsc will be better as API name because the last TSC value is
easier to understand.
Then add necessary unit test and update the unit test framework.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5e465e9283c032acb427576d0c90f9e1414f2271
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1048
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
The revert asynchronous API doesn't run as the *real* asynchronous
way, because the drive can only support synchronous module and only
1 session is supported. The reason why we added this API is that
RPC call has the default timeout value here, while the revert may
take over several minutes, the API itself doesn't short the revert
action, so just remove it and use the synchronous API instead.
The revert action will erase all the users data and bring the drive
back to the factory state, it should run in the synchronous mode,
so just remove the asynchronous API and we can increase the timeout
value when using RPC to call this API.
Change-Id: I08a082edea6385e378399423bbb229d05f8bc262
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1232
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
super->clean value signifies if blobstore was unloaded
cleanly.
If it was not, then during bs_load the _spdk_bs_recover()
procedure if called.
Meanwhile bs->clean is always set to 1 after load, causing very first
blob_persist to also re-write super block with the super->clean
set to 0. To signify that md has changed and possibly trigger
the recovery if clean bs unload does not occur.
When the re-write of super block succeeds the bs->clean is set to 0,
because further re-writes of super block are not needed on next
blob persist.
This patch resolves issue when:
1) reading super block fails - execution should backoff, to prevent
writing an empty buffer as super block !
2) writing super->clean = 0 to the super block fails - execution
again should fail, and bs->clean should not be set to 0. It will
cause next persist to attempt re-write again.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ia07cc5c6c107310059b50886edb7283c176b9169
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1164
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This change verifies that not only it is possible to open
the snapshot, but also the spdk_bs_create_snapshot() reported
success.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ifb7fcc91802c838710f1f9be41090057268a5900
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1262
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
blob_create_snapshot_power_failure() test always attempted
snapshot creation until the snapshot did open.
Which meant that on bs reload after dirty shutdown,
the original blob might be in unrecoverable state.
UT did not verify create call beyond that point.
Next patch will stop after snapshot is possible to be opened,
AND the spdk_bs_create_snapshot() returned success.
This patch makes it easier to recreate same starting
conditions after snapshot did not open.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I1901b29a8319b2203a855e7879821ed3850f4917
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1261
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
In general it is not possible to delete snapshot when
there are clones on top of it.
There is special case when there is just a single clone
on top that snapshot.
In such case the clone is 'merged' with snapshot.
Unallocated clusters in clone, are filled with the ones
in snapshot (if allocated there).
Similar behavior should have occurred for extent pages.
This patch adds the implementation for moving EP from
snapshot to clone along with UT.
The UT exposes the issue by allowing delete_blob
to proceed beyond just unrecoverable snapshot blob.
Fixes#1291
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ib2824c5737021f8e8d9b533a4cd245c12e6fe9fa
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1163
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch is used to add the async network I/O support in
sock layer. If code is configured with I/O uring, --with-uring,
we can use io uring in Linux (version >=5.4-rc3).
PS: We also make VPP's default priority > uring, because
for the iSCSI or sock test linked with VPP. It tests VPP with
a given address (which is not a special VPP can only open address),
so using uring can also listen those address succefully. And if we make
uring with priority > VPP, actually, VPP will not tested in those cases.
Additionally, the current CI pool is not ready for test, we need
wait for the CI system ready. And I test on my local platform, it works.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Ie8ee3c8ddf8d2a7264f2b382376733e002816dcc
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/952
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Previously the macro SN32_LT and SN32_GT had been added to iSCSI
library. But such comparisons may be used in other libraries.
So add two inline helper functions spdk_sn32_lt() and spdk_sn32_gt()
to include/spdk/util.h.
Add unit test for these functions. These functions are located in
header file but math.c is the place if they are located in source file.
Hence add unit test as the one for math.c.
The next patch replaces the macro SN32_LT and SN32_GT by
spdk_sn32_lt() and spdk_sn32_gt() in iSCSI library, respectively.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Id3e4d80fea98ad4ae1516e27b9c9e8ec6f37e7a8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1346
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
NVMe specification in ch.7.6 "Controller Initialization" suggests to
use only Set Features "Number of queues" command and says nothing
about Get Features. All required information is available after Set
Num Queues step.
Fixes#1270
Signed-off-by: Evgeniy Kochetov <evgeniik@mellanox.com>
Change-Id: Ide38ba9c7f063f1d6b13bfce4232c588cc906784
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1271
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The next patch will create poll group threads dynamically for
NVMe-oF target, and will need to wait for completion of poll group and
I/O channel destroy. This is a preparation for the next patch.
Add callback function and its argument to spdk_nvmf_poll_group_destroy(),
and to struct spdk_nvmf_poll_group, respectively.
The callback has not only cb_arg but also status as its parameters even
if the next patch always sets the status to zero. The reason is to follow
spdk_nvmf_tgt_destroy's callback and to process any case that the status
is nonzero in future.
spdk_nvmf_poll_group_destroy() sets the passed callback to the passed
poll group.
Then spdk_nvmf_tgt_destroy_poll_group() calls the held callback in the
end.
This change will ensure all pollers are being unregistered and
all I/O channels are being released.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifb854066a5259a6029d55b88de358e3346c63f18
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/495
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
blob_delete_snapshot_power_failure() test always attempted
snapshot deletion until the snapshot did not open.
Which meant that on bs reload after dirty shutdown,
the snapshot was in unrecoverable state.
UT did not verify delete call beyond that point.
Next patch will stop after snapshot is unrecoverable,
AND the spdk_bs_delete_blob() returned success.
This patch makes it easier to recreate same starting
conditions after snapshot did not load.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I7e14e8dadaaef4aa3287ebd376465253466b2362
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1162
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This reverts commit ea5ad0b286.
This code is moving from the nvmf target to the posix sock
layer in this series.
Change-Id: I333bdf325848e726ab82a9e6916e1bbdcd34009c
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/446
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Now that a namespace can be depulated asynchronously now, the NVMe bdev
module should also be finalized asynchronously, after all namespaces and
controllers are deallocated.
Change-Id: Ic082fec8e31e9bd5ee1c698cd8dfca9f248776d3
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1198
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch adds the ability for a namespace to be depopulated
asynchronously. Currently both regular NVMe namespaces, as well as the
OCSSD ones are depopulated synchronously, but it'll be changed in the
upcoming patches.
The nvme_bdev_ctrlr.ref is now not only tracking the number of bdevs
created on that controller, but also the number of populated namespaces.
Change-Id: I7b112d9b0d41739f3dc7d427e9da340843128c54
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1197
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add thread_count to struct spdk_reactor to count number of threads
per reactor. This number will be used in the next patch to know
if all threads are idle or not for each reactor to support CPU
power saving.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4f7cc5a6b78d85e9f8d0b539c60058c13e282759
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1169
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Since the OPAL here is just for NVMe device, so we don't need to use dev_handler as common
handler, just rename it to spdk_nvme_ctrlr. And we don't exit the initialization if
OPAL construnction had a failure. Also move the timeout initialization to construct().
Change-Id: I11f0aea961eaa3da0c6253eb03d0227f7e7e5f11
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1101
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Added new setup/cleanup functions for a suite of
unit tests that use a particular blob through out the
tests.
This simplifies the contents of particular UTs,
and brings forward focus of each UT.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ib7d69b90fcbe8e6a0ba303475fcbaeb90fa110a7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/945
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Some of the unit tests were only closing a blob,
without deleting it at the end of unit tests.
This is valid behaviour, but to later simplify
the setup/cleanup - a delete blob was added.
This change was made to unit tests where,
it was not focus of particular UT.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I7e338ba6fcb63af26658e8968971a6d56f70807b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1203
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Operation of closing and deleting a blob is common
throughout the tests.
This patch creates helper function ut_blob_close_and_delete(),
to do exactly that with the right asserts.
Throughout the UT this function replaces all instances where
blob is closed and deleted, when it is not the subject of
particular unit test (focus is on other functionality).
It will allow to later use it in setup/cleanup functions
for UT suite - similar to bs init.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ic56594da8cd4c442b62890d62961b44771059679
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1202
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Operation of creating a blob (with or w/o opts),
then opening it through out the tests is quite common.
This patch creates helper function ut_blob_create_and_open(),
to do exactly that with the right asserts.
Throughout the UT this function replaces all instances where
blob is created and opened, when it is not the subject of
particular unit test (focus is on other functionality).
It will allow to later use it in setup/cleanup functions
for UT suite - similar to bs init.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ia541b855d154503f824bfa3909bcfeac649c5853
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1201
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Always call API on blobid that was received from blob
create, instead of relying on global one.
Where necessary added declaration and assignment.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I3529b4d5e86c1301bb64268029a57873f9f600cb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/944
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Always call API on pointer that was received from blob
open, instead of relying on global one.
Where necessary added declaration and assignment.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I15531111201d071c471f5be79ce18ff508631677
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/943
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
A lot of unit tests require only creation of a blobstore
then unload it at the end.
This code can be made common and invoked automatically by
CUnit with CU_add_suite_with_setup_and_teardown().
Those functions are called before and after each test in suite.
This should simplify the unit tests by removing the common
code.
Following patches will add further suites with different
setup/cleanup to reduce common code even more.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I984cde2381f4461e188e06050355024a88ebfca9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/932
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Next patch in series adds setup/cleanup functions
that use g_bs for its operation.
Particular unit tests should not leave the g_bs
unassigned, if cleanup is supposed to unload it.
It applies to helper functions to reload/dirty_load.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I6e022b6c762981c2c70ebf31f4981a17f54f3591
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1182
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Some of the unit tests initalized bs opts,
event if they were left unmodified.
There is no need to perform this operation,
as spdk_bs_init() can accept NULL as bs_opts parameter
to just initialize default values.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Iacea1fa9d53796b8c359b611092cc63c6bce4094
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1181
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add the error print if there is still remaining_size in
order to provide more meaningful debug info.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I7b15c9c9a630ea7ecb2d3191b73c9c99f7febf31
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1189
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
subsystems
This is optional and most transports will not implement it.
Change-Id: I51e0f1289b0e61a8bdb9a719e0a2aae51ecb451c
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/629
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
In the next patch a new transport call will be added to notify
transports of subsystem->listener associations. The operations the
transports may need to perform there are likely asynchronous, so make
this top level call asynchronous here in preparation.
Change-Id: I7674f56dc3ec0d127ce1026f980d436b4269cb56
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/628
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This was recently made asynchronous to support virtualized transports.
However, we're moving to add a new call to associated a listener with a
subsystem to transports and the operation that needed to be asynchronous
will actually be performed there. For simplicity, make this synchronous
again.
Change-Id: Ie98136a19c58f0f9bba0d140476de3bbb38e12d7
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/881
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch adds better check if the xattr was removed.
It will identify potential bugs when first md sync
takes precedence over the second md sync.
As per suggestion in
https://review.spdk.io/gerrit/c/spdk/spdk/+/774/6/test/unit/lib/blob/blob.c/blob_ut.c#7655
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I463f2455614ef11cc1512dc2fb1972ba1f024337
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1109
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Operation of dirty shutdown of blobstore and reloading
it occurs often enough in UT to provide a common function
to perform it.
Added ut_bs_dirty_load() to facilitate this.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I0079dfabd64eaec6495db02fe200be1d6116f0c7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1092
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Operation of unloading and loading blobstore
occurs often enough in UT to provide a common function
to perform it.
Added ut_bs_reload() to facilitate this.
Couple occurences in this patch actually fix
test cases where mistakenly opts were not passed.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ib46ed395cd134feaa540e00a334ae861872b3ef4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1091
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Couple unit tests were still refering to g_bs pointer,
rather than the one local to particular UT.
This patch fixes this.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: If343eb561a48c4547d499139d76e1db6b2d7f3bf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1090
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Currently we will free the cache buffers in the file R/W
data path, however we can start a thread to do the cache
buffer reclaim regulary, so that we don't need to free
the cache buffer in the Rocksdb thread context. By
doing this, we can also remove the global cache buffer
lock in following patches.
Change-Id: Icb0fbc49baecd1e9d86a5fcfe400758dfc3c53a2
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/941
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
To avoid the starnge formatting, typedef has been used. But this comment
is hard to get the meaning. So stop breaking after return type for this case.
The strange formating is
struct spdk_scsi_dev *
spdk_scsi_dev_construct(const char *name, const char *bdev_name_list[],
int *lun_id_list, int num_luns, uint8_t protocol_id,
void (*hotremove_cb)(const struct spdk_scsi_lun *, void *),
void *hotremove_ctx)
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I20c30b225b3b96fa9207b4a89e3210c8a97fb1d8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1050
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Add raid5 module and unit tests. Use './configure' with option
'--with-raid5' to enable it.
Change-Id: I9f07da8c3567fa65499444899c899adaa2e29550
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/855
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
If we did not configure with "--enable-debug". it will
trigger the compliation failure since this function is
not defined.
Change-Id: Ia1795da736be55d4dd1418a2e74edefff7797f11
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1097
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
When running unittest_thread in fedora29 with memcheck, there is
error "Conditional jump or move depends on uninitialised value(s)"
in for_each_channel_unreg test.
Signed-off-by: Richael Zhuang <richael.zhuang@arm.com>
Change-Id: I38abf4c70ff513e39232b83357d571dded8f02c3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1072
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Replaced single global write buffer with the per-io_channel write
buffers. This means that the "rwb" module and all of its references
were removed and replaced with the recently added interfaces.
Change-Id: Idc899d3a4d63a8a2bede1ac26549ed06e9a2e784
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/909
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Added queue responsible for keeping track of full, ready to be written
batches. A batch might be put on this queue in case it'd already been
filled, but could not be written out due to lack of resources or it was
written out, but failed and needs to be resent.
Change-Id: Iba49cd359425300d21b8100f13f17189e99d4c7c
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/908
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Maciej Szczepaniak <maciej.szczepaniak@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Two functions were added:
- ftl_get_addr_from_entry() returning an address pointing at a given
entry
- and it's inverse, ftl_get_entry_from_addr(), returning a write buffer
entry for a given address
Change-Id: Iea1e2e59f240f50183fdb549280a0f0b722efbef
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/906
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch adds the ftl_batch strucutre, which describes a single batch
of data to be written to the disk. It's comprised of multiple write
buffer entries (the actual number depends on the write unit size of the
underyling device).
Additionally, a function responsible for filling out a batch was added.
It iterates over available IO channels and dequeues submitted write
buffer entries until a batch is completed. The IO channel queue is
shifted, so that each time the function is called a subsequent IO
channel is used first, which guarantees that all channels are treated
fairly.
Change-Id: Ie61d8c6cb51d5c5175540c975447bc27590c5cb4
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/905
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Added functions responsible for acquiring/releasing write buffer entries
from the per-io_channel caches. They're also in charge of limiting user
writes by reducing the number of available entries to the user.
Change-Id: I23adfe36065139036f9b72a016e34fbf6eb29230
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/904
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The IO channel pointers are now stored inside an array of the device
they belong to. Once write buffer entries are tied to IO channels,
it'll provide a method for dereferencing an entry from its address.
Change-Id: Iaf401525eb0f5af8dc6047a1dc8bae11b56761d7
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/901
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This is the first patch of a series that replaces single global write
buffer with per-io_channel buffers. This change is intended to improve
performance for multithreaded workloads.
This patch changes the way the ftl_io_channels are allocated by only
keeping an ftl_io_channel pointer inside spdk_io_channel's context. It
allows for delaying IO channel destruction, which in turn allows the FTL
to iterate over all exisiting IO channels without locking.
Change-Id: I5e0cab8043a2b5f747e971dd3d65ed2546c8cf26
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/900
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add a flag resched to check if reschedule operation is requested
to struct spdk_lw_thread. Add _reactor_resquest_thread_reschedule()
to set the resched flag, and add it to the case SPDK_THREAD_OP_RESCHED
in spdk_reactor_thread_op(), and return true in the case
SPDK_THREAD_OP_RESCHED in spdk_reactor_thread_op_supported().
Then _spdk_reactor_run() checks if the resched flag is true for each
thread. If true, set the resched flag to false, and remove the
thread and call _reactor_schedule_thread(). Add continue to avoid
use-after-free issue for both reschedule and terminate cases.
This idea follows voluntary thread termination and will remove our
worries for all complicated rare cases.
Add unit test case to verify this update.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I656872d32dbb469ae70f771cd0419a77236bfe18
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/500
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Since ftl supports only one core thread ftl_thread
structure is not needed anymore.
Change-Id: I66eda9249d74b3eff0c4473dcd0aba4a6135e296
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/548
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Maciej Szczepaniak <maciej.szczepaniak@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Add tests for the following features:
- SPDK_NVME_FEAT_TEMPERATURE_THRESHOLD (4),
- SPDK_NVME_FEAT_ERROR_RECOVERY (5),
For Temperature Threshold feature the validity of the THSEL and TMPSEL
is covered as described in the NVMe spec (1.4):
"Figure 279: Temperature Threshold – Command Dword 11"
For the Error Recovery feature the validity of the DULBE is covered
as decribed in the NVME spec (1.4):
"Figure 280: Error Recovery – Command Dword 11"
Random value is selected for the lsb in the cdw11 (0x42).
Change-Id: Ia57ab4d79439ec315ddc9bbfdad8400aa926062a
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/692
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Remove the prefix "spdk" from spdk_reactor_schedule_thread(), add
spdk_reactor_thread_op() and spdk_reactor_thread_op_supported().
For SPDK_THREAD_OP_NEW, spdk_reactor_thread_op() calls
_reactor_schedule_thread() and spdk_reactor_thread_op_supported()
returns true.
Then replace spdk_thread_lib_init() by spdk_thread_lib_init_ext()
with spdk_reactor_thread_op() and spdk_reactor_thread_op_supported().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I232a3b2c6bcaf4d86b0dd3cefacd3e47eadda6d8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/968
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add enum spdk_thread_op and two function typedefs spdk_thread_op_fn
and spdk_thread_op_supported_fn.
The first operation type of enum spdk_thread_op is SPDK_THREAD_OP_NEW,
and it is used as an alternative to spdk_new_thread_fn.
Add global variables, g_thread_op_fn and g_thread_op_supported_fn, and
then add spdk_thread_lib_init_ext() to initialize these.
spdk_thread_lib_init() requires both of thread_op_fn and
thread_op_supported_fn are specified or not specified.
spdk_thread_create() calls g_thread_op_fn() with SPDK_THREAD_OP_NEW
if g_new_thread_fn is NULL, g_thread_op_supported_fn is not NULL,
and g_thread_op_supported_fn(SPDK_THREAD_OP_NEW) returns true.
Update unit test to test these addition.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I56db903f62437f6ff3198248ffc5dede396c22bc
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/967
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
There is a warning triggered when holding ref to const obj and passing
to these getters.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I2c7b4ea0d325d84d66923fc524273ea44a3a311b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/997
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
With the JSON configure, the base device will be opened on the
same thread (RPC thread) to handle the JSON operation. Later the
virtual device upon the base device can be opened on another
thread. At the time of virtual device destruction, the base
device is also closed at the thread where opening the virtual
device, it is actually different than the original thread where
this base device is opened through the JSON configure.
Add a thread here to record the exact thread where the base
device is opened and then later route it back to handle the base
device close operation.
Change-Id: Ib95e8d190bd87158ae1ecc6698da95ccc4ba9579
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/992
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There are synchronous security send/receive APIs defined in nvme.h,
however, we still need the asynchronous APIs so that we can make the
OPAL library can be used in asynchronous way. As the asynchronous APIs
are already defined in nvme_ctrlr_cmd.c, so just export them to public
APIs.
Change-Id: I5646f342a4bf70faad37daa956476f05a1327bcc
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/675
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
When running unittest_nvmf in fedora29 with memcheck, there are
many errors about "Conditional jump or move depends on uninitialised
value(s)". The failed tests are:
in ctrlr_ut:
test_reservation_notification_log_page
fused_compare_and_write
in ctrlr_bdev_ut:
spdk_nvmf_bdev_ctrlr_compare_and_write_cmd
Signed-off-by: Richael Zhuang <richael.zhuang@arm.com>
Change-Id: Ib1e6a744e86876c15ee53206909364e853574dd1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/965
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
while the size of namespace is changed,
the resize event will be notified.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Evgeniy Kochetov <evgeniik@mellanox.com>
Signed-off-by: Allen Zhu <allenz@mellanox.com>
Change-Id: I5d85f17df898dc21c0ae1eb9f529dcb624a457ac
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/849
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Always call API on pointer that was received from blobstore
initialization or load, instead of relying on global one.
Where necessary added declaration, assignment and asserts.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ic4198ac984c13a8b77428deaa32ce9864e6750c1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/942
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
CUnit provides a helper macro CU_ADD_TEST() that
simplifies using CU_add_test() function.
Test name no longer needs to be provided,
instead test is named after test function name.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I9f5d9e0d8e72ab36b2a5c04e33c336e6c0a1fa6a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/931
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Failure to prepare CUnit for tests is always a fatal error,
and application exits.
Most test managment functions in CUnit set some CU_ErrorCode,
that can be retrived by return code from a function or CU_get_error().
Thus usual structure of UT in SPDK checked every output from every
test managment function.
There is a helper function CU_set_error_action() that when set to
CUEA_ABORT, will abort the application run with proper error return code.
Along with nice error message.
For example if one were to add same UT twice:
"Aborting due to error #32: Test having this name already in suite."
Application return code set to 32.
Using CU_set_error_action(CUEA_ABORT), removes the need for error checking
on test managment functions in CUnit.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ida7de5e040b714509e79957d47a006ee518a42b8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/930
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Expands blob_simultaneous_operations to cover case
when second md sync is perfomed without waiting for the first
one to complete.
The blob state is forced in UT, but in normal usage could be
changed by modifying xattr, allocating thin clusters or other.
Related to #1170
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I880d289cdf957d4513c080efdcb7a5d8c6b3b447
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/775
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This new UT is checking validity of md sync being run
along another md sync with changed metadata.
At this time added case where first md sync is being
interrupted by removal of xattr with second md sync.
This interruption is perfomed at increasing number of
poller executions, until the number is enough to
complete first md sync.
There are two expected states of used_md_pages array,
either with xattr or without. The state is verified
after md syncs.
This UT will be expaned in similar manner by other
operations (than xattr) that casue changes in persisted metadata.
Related to #960
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I251dca92ffc3080d8dc503a7f1ff342aa59adef9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/774
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Making use of recently added utility to poll exact number of times.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I23a9dc702c899285626522ace8ec77a9ba0f7757
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/773
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
To make room for other raid module unit tests.
Change-Id: Icf8b8ff0c9051ccb4c7ebd784807370f8be1a8fb
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/853
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Allow ftl_io initialization with a iovec array instead of a single data
pointer. It'll make it possible to use the vector version of the IO
commands.
Change-Id: I34c1e398cea681f59321605e081366785aa29128
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/894
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Maciej Szczepaniak <maciej.szczepaniak@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
It is memory optimisation as transport id is 'heavy'. As a side effect
simpler handling of listen and stop_listen on transport specific layer.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I4e9d0e0c5eee2d570ec4ac9079270c32d5afb8db
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/626
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The copy engine library, modules and public APIs have been renamed.
Use of the word `copy` has been replaced with the word `accel`
short for accelerator in preparation for adding new capabilities
in the future. Additionally, APIs for what was previously called
the `memcpy` engine have been renamed to identify the engine as a
software accelerator.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ia607aa718416146fbba1e6792b8de0f66bd8a5de
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/576
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Dry run processing in iscsi_parse_portal() now only checks if
portal string is not NULL. Portals are managed not by fixed size
array but linked list now. Hence dry run processing is not needed
itself now.
So remove the dry_run parameter from iscsi_parse_portal() and
the dry run loop in iscsi_parse_portal_grp().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ib7cb444b51581b8ee603388aad34bc58d1cc9023
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/493
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
The next patch will create a SPDK thread for each poll group at
startup. Hence iSCSI configuration management will be done by
different thread from these poll group threads.
Hence send message explicitly to add connection to poll group even
at startup. We can do this for the current master branch.
Remove some code related with SPDK thread framework from unit tests
for iSCSI portal group because thread management is moved to
connection.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I40cacdb2066f65866f7ef83cf3b3e4e8b8cd322e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/489
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This allows to avoid calculation of ioccsz bytes on each request
and removes access to "cold" ctrlr structures in data path.
Add UT to check validness of calculation
Change-Id: I55ceff99eb924156155e69a20f587a4f92b83f0b
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/519
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
When running sock_ut in fedora29 with memcheck, there is an error
"Syscall param sendmsg(msg.msg_iov[0]) points to uninitialised
byte(s)".
Signed-off-by: richael zhuang <richael.zhuang@arm.com>
Change-Id: Iaddb85ed2da2f45e200569c936f05174bc89c99b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/874
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
If set, SPDK will continue loading the JSON config even if
some commands caused an error. This can be useful when loading
RPC config from spdk_tgt into e.g. bdevperf, which supports
only a subset of RPC commands and would usually fail with
"Method not found" message.
Resolves#840
Change-Id: I070fea862fd99e5882d870e11e6a28dc9d0c8ba6
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/620
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is a preparation to support voluntary thread termination by
calling spdk_thread_exit().
The comment in the header file has already said that all associated
I/O channels must be released before calling spdk_thread_exit().
This patch actually checks if it is satisfied in spdk_thread_exit().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I56ac50b561c6ca91d3dc2d60c21c8d91d38f081b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/823
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This is a preparation to support voluntary thread termination by
calling spdk_thread_exit().
Change spdk_thread_exit() to return -EBUSY if the thread has any
registered poller. We enforce all pollers including paused poller
are unresitered before the thread is marked as exited.
By this change, a bug was found in reactor_perf test tool. Fix it
by adding spdk_poller_unregister() and add the g_ prefix to avoid
future potential errors.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If7f40357c9a6f4101b3998ea0da3cc46cc435031
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/487
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This is a preparation to support voluntary thread termination by
calling spdk_thread_exit().
Change spdk_thread_exit() to return -EINVAL if the thread is already
marked as exited. This will be helpful to detect wrong call sequence
of voluntary thread termination.
Besides, update reactor shutdown and unit test framework shutdown
to incorporate this change accordingly.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I2296c61e273bf4d9580656dcbc2da0e8a8f3bcf7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/671
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This is a preparation to support voluntary thread termination by
calling spdk_thread_exit().
By the last patch, the asynchronous release of I/O channel will
complete even after spdk_thread_exit() because pending messages will
be reaped.
Then this patch stops new allocation of I/O channel after
spdk_thread_exit().
Hence we will be able to release all I/O channels for exiting
thread within finite time.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I48a45bcba7c4b2c62d8c9d398ac35a584b533627
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/821
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This is a preparation to support voluntary thread termination by
calling spdk_thread_exit().
Previously, the exiting thread had discarded all pending mesasges.
We change this to stop accepting any new message in spdk_thread_send_msg()
and reap pending messages in _spdk_msg_queue_run_batch().
Add unit test case for the new behavior. Adding g_ prefix to global
variables for clarification is done together.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ida78e7bb1b86357602aea6938dd514897b67edd6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/482
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
The test case for_each_channel_remove() did not have any
assertion and the count was not incremented correctly.
This patch fixes several issues in for_each_channel_remove()
by counting spdk_get/put_io_channel() and spdk_for_each_channel()
correctly and achieves what we wanted to do in this test case.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iceffd924f8887452bd7dad48e30d121874ab0b05
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/483
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
With the recent changes which added usage of writev_async to
both TCP target and initiator, nvme_tcp_pdu::writev_offset
becomes useless since it is not updated in data path. This
field is only used in UT. Remove this field from nvme_tcp_pdu
structure, now nvme_tcp_build_iovs builds iov which fully
describes the PDU. Update UT accordingly.
Field padding_valid_bytes is not used at all, delete it too
Change-Id: I2d6040ae64d6847cb455f59f65ec5677de8e5192
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/483374
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
spdk_put_io_channel() was designed to be called on the same thread
that called spdk_get_io_channel(). spdk_put_io_channel() sends a
message to its own thread, to allow the context to unwind before
releasing the resources. This had the side effect to allow an
incorrect thread to call spdk_put_io_channel(). This patch will fix
that.
Bdevperf tool had a design flaw that needed the side effect, but
it was fixed recently. We do not know if we have any other case.
Hence add assert to spdk_put_io_channel() to find other case.
We found that unit test for blobstore had called
spdk_put_io_channel() and fix it together in this patch.
Besides, correct the comment for spdk_put_io_channel() in
include/spdk/thread.h not to create any other case in future.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6ec7bf074818abef43b23ca40bc9385adac70a75
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479390
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This internal interface allows to create nvmf ctrlr and connect io
qpairs on add listener rpc request (i.e. when subsystem is stopped
and listener is not yet on subsystem's list).
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I998cb72ed773094faacc6668cf069ba9e2a6bf50
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481409
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Had to remove one part of a unit test because the null
checking is moved to a different function.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I0a95d0a9a9a5708416fdc7efefb36e17b1ffe010
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/480008
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
When attempting to decode a base64 string, while there is a way to
calculate the maximum possible decode length, there isn't a way to
calculate the exact decode length without duplicating some base64
specific logic located in spdk_base64_decode. With this change, the
spdk_base64_decode function can now optionally calculate the exact
decode length without actually performing the decode by passing NULL
in as the dst argument.
Change-Id: Ice83db979f86a6fe9f39d236d3083102ca37ec68
Signed-off-by: Mike Carlin <mikefcarlin@protonmail.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479479
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Extent table and extent page descriptors are now
set to be default way clusters are serialized on disk.
With this patch UT are ran with and without
extent table.
Changed two asserts in test, since amount is dependent on
which type of serialization is used.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ica58fce6a4effd014d7dd40ee26edd0fa3196d0f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481901
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This will be used to add another run of whole UT suite
with extent pages on/off.
Next patch in series will be enabling both types of
extent serialization for all UT.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ia8b4b8822edefb90ffc13cf777885f9af95e4545
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482170
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
All the non-ext version of the call is doing, is calling
ext with NULL as opts. Then default opts are used in
its place.
This change was facilitated by next on in series,
where all blob opts will be initalized in UT
with parameter use_extent_table either set to
true or false.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I62b642c1808b38a5f7c94a5900f25f4978a4ec39
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482859
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
A pointer to a stack variable is passed as an argument to
nvme_completion_poll_cb function, later this variable is used
to track completion in the spdk_nvme_wait_for_completion() function.
If normal scenario a request submitted to the admin queue will be completed
within the function which submitted the request.
spdk_nvme_wait_for_completion() calls nvme_transport_qpair_process_completions
which may return an error to the caller, the caller may exit from the
function which submitted the request and the pointer to the stack variable
will no longer be valid. Thereby the request may not be completed at that time
and completed later (e.g. when the controller/qpair are destroyed)
and that will lead to call to nvme_completion_poll_cb with the pointer
to invalid stack variable.
Fix - Dynamically allocate status structure to track the completion;
Add a new field to nvme_completion_poll_status structure to track status
objects that need to be freed in a completion callback
Fixes#1125
Change-Id: Ie0cd8316e1284d42a67439b056c48ab89f23e0d0
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481530
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
After creation of blobs in both tests, only clusters indexed from
0 to 10 are supposed to be used. Index 0 for md and 1-10 for data
of single blob since it was create thick provisoned.
Cluster allocations are done in order so if there was a bug for
overflow amount of clusters claimed, first in order would be
one with index 11.
This patch adds asserts after each bs load for first data cluster
that is supposed to be used and for first data cluster that is
not.
During the tests those should remain constant.
When creating/deleting snapshots, the blobs are affected
by changing their type to/from thin_provisioned.
Added asserts to verify their state at every blob open.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I38418da55850d5b8468e578b3c42c5b817ae8045
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482661
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
g_bserrno from blob deletion or snapshot creation,
should not be checked. It is implementation
dependent whether the error (or success) from those
calls actually means that enough data was persisted
on disk.
This test case should work even if we set the threshold
high enough that no failed opperations occur.
On the other hand some parts of those calls do cleanup
in them, meanwhile there is enough metadata data on disk already.
Such as cleaning up unused clusters or pages issue
writes, but at that point the blobs already are in expected
state.
Thus removed assert for g_bserrno, as failure is not indicative
of impossibility to recover.
While here, removed the spdk_bs_unload(). This UT are for
testing power fail safety. Never should it be the case that
enough writes occured in create/delete, but blobs are not
in the expected state.
When such bug would be introduced, it could be covered up
by spdk_bs_unload() cleanly closing up the blobstore.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ic69c3061f2cc1fe04bf895632cdb11efb2fe6912
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482660
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Extent Pages claim and insertion can be asynchronous
when cluster allocation happens due to writing to a new cluster.
In such case lowest free cluster and lowest free md page
is claimed, and message is passed to md_thread.
Where inserting both into the arrays and md_sycn happens.
This patch adds parameters to pass the Extent Page offset
in such case.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I46d8ace9cd5abc0bfe48174c2f2ec218145b9c75
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479849
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
If available, automatically use MSG_ZEROCOPY when sending on sockets.
Storage workloads contain sufficient data transfer sizes that this is
always a performance improvement, regardless of workload.
Change-Id: I14429d78c22ad3bc036aec13c9fce6453e899c92
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471752
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Or Gerlitz <gerlitz.or@gmail.com>
With our target design, there's no advantage to sending
multiple R2T PDUs per nvme command. This patch starts by
setting up the math so that at most 1 R2T PDU is required
per request. This can be guaranteed because the maximum
data transfer size (MDTS) is pre-negotiated in NVMe-oF
to a reasonable size at start up.
It then proceeds to simplify all of the logic around mapping
requests to PDUs. It turns out that the mapping is now always
1:1. There are two additional cases where there is no request
object at all but a PDU is still needed - the connection response
and termination request. Put an extra PDU on the queue object
for that purpose.
This is a major simplification.
Change-Id: I8d41f9bf95e70c354ece8fb786793624bec757ea
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479905
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
We can always accept up to the maximum I/O size in an H2C,
so eliminate the #define.
Change-Id: I349dab5f9b6ec482a7c580b1396e03c8d30a250b
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/482278
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The resources allocated to a queue pair do not need to be directly
correlated to the queue size requested by the initiator in NVMe-oF, as
long as enough resources are present. The RDMA transport, for instance,
does complex pooling of the resources behind the scenes when using a
shared receive queue.
Simplify the resource allocation for a TCP qpair to just always allocate
the max allowed queue size right away. This is a configurable parameter,
so system administrators can adjust for their needs. The initiator may
then request a queue size less than or equal to that, which will only be
enforced by queue depth counting and not impact the actual number of
resources allocated on the target.
This change relies on the MaxC2HSize being equal to the Maximum Data
Transfer Size (MDTS) reported. That is the default configuration, but
MDTS is configurable. Changing the MDTS with this patch to a value
larger than 128k will cause the target to break. This is addressed in
the next patch in this series.
Change-Id: Ibd4723785c6a4d8d444f9b7bbfa89f98de2320f5
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479733
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Add call for spdk_nvmf_bdev_ctrlr_compare_and_write_cmd
function in spdk_nvmf_ctrlr_process_io_cmd function
when fused command is discovered.
This patch also removes redundant defines for fused flags.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I61971a56577ab32b52e1fde1e572f718a9a2d9aa
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476621
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch introduces new spdk_nvmf_bdev_ctrlr_compare_cmd
function which implements support for compare operation.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Iadf402a6441a78ea0e6468f1066c6b0e10e63b9b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477782
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Use new bdev aux buf feature. Huge performance benefit for writes.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I5a27460a369ef5f13bf490a287603e566071be41
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478384
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is prepared for the further call back usage.
Change-Id: Iccf304c87e67debfb4e7c330acc9cc233cc3ec48
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481917
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch eliminates the flushing logic and simplies
the writev logic. And this patch can also improve the performance.
We support async write for PDUs other than login response, logout response,
and text response in this patch. We will support async write also for them
later in this patch series.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I243f598f297d594da0bb18466bc47dab918ed3ee
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481686
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Changed write function to be able to work in zone append mode.
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: I3af98f1d8e69eac6922e19addebabbc6ce847c63
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468042
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Handle finish zone management function to zoned block vbdev
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: Iffe24572609e741a79b6bb92f72b56cede4906ca
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468041
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Handle close zone management function to zoned vbdev
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: I001e25a157ba738724012ca366ef901016733944
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468040
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Added handling of reads to a zone; blocks outside of a write pointer
are zeroed out.
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: Iaf60d6ff74caf9831998862e048446ccd0a0fa3f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468038
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Added handling of write commands, including zone state changes and write
pointer updates.
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: I576ca18b52474bb299c20296a7561f25e5afa85b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468037
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Add handling of two of the zone management commands for vbdev.
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: I2868a96d15acbc2d13d18dea405b6d98cb4573d6
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468039
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Accept a clear method option on blob create by adding clear_method
to the opts structure passed in to _spdk_bs_create_blob(). Store
these 2 bits in md_ro_flags so that earlier versions without an
understanding of these bits can not alter metadata.
The new metadata values will be used later in the series.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I5440645ca20b426778d13b2e544b65dc2b3b83c7
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472204
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This commit provides the capability to install a
custom admin command handler for NVMF.
It can be used to implement or replace NVMe admin commands that
are currently not handled by the NVMF subsystem.
The handler implementation is pretty generic and the handler function
has to figure out what to do with the command based on the bdevs
that are configured for the subsystem.
In cases where admin commands need to be forwarded to an NVMe bdev,
the commit provides functions that allow access to the underlying bdev.
There is an example handler in lib/nvmf/custom_cmd_hdlr.c.
Change-Id: I4f9d538c53669c176a836e8bdd379db0070a87dc
Signed-off-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479167
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: <jacek.kalwas@intel.com>
For the latest QAT devices there are 3 CPMs each with 16 VFs and
2 qp each VF. To load balance for multi-thread operations we want
to assign each new queue pair (QP) on a per CPM (processing module)
basis so this patch assigns the next QP, for QAT, by taking the
last + 32 modulo the total number of QP. This will results in each new
channel getting a QP on the next CPM.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Iea608ada68517b6f2faecd45701c7aae6d23a2d0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477082
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Previously one global list of device/qp combinations was used
regardless of PMD and when assigned, the device name was checked
to make sure a matching one was pulled from the list.
Later in this series a patch will make use of having different
lists as we discovered a decent way to load balance QAT but the
implementation with all PMDs on one list was too complex.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I54dfbd0206a881d126831ba27a4ae05cdc6f7c11
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477152
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Update error handling of spdk_nvme_wait_for_completion_robust_lock to
differentiate cases when request is completed (possibly with error)
or polling was aborted by transport/device error
The function returns 0 on success, -ECANCELED if transport/device
error occurred and -EIO if the request is completed with error
Change-Id: Ibf7f3c330317af0d8f27ba9cd10d8b773f6a796b
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481529
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Update error handling of spdk_nvme_wait_for_completion_timeout to
differentiate cases when request is completed (possibly with error)
or polling was aborted by timeout or transport/device error
The function returns 0 on success, -ECANCELED if transport/device
error occurred or operation timed out and -EIO if the
request is completed with error
Change-Id: I314f40d1acaa6cfa9b88e5417b1ee2c9801bbbd6
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481528
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
"lbk" name is more OCSSD specific so in
generic FTL "block" name is more suitable.
Change-Id: I792780297b792bf5e02f13cc20346da56b032918
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472284
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Zone append command allow to write to the
zone with queue depth greater than one.
Append location is read during write
completion callback.
Change-Id: Ie08ce8d31d5d0fb521cdc2b95f3e29b92e02e63f
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471627
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
This patch removes parallel unit and zone id fields
from ftl_addr struct.
Change-Id: Ica42208eafdbbecab60430708197f5f3ba6167d6
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468701
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
This would allow to respond for add listener rpc request even
when there are async calls in transport specific function.
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I94a9f45b7ba9e8d46a60ae3785953cea12554732
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479511
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Added handling of get zone info command
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: I2d80885af83345c945af22a46a41abf55e1eb413
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468036
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Added zone specific information during initialization (starting LBA,
capacity etc.)
Signed-off-by: Kozlowski Mateusz <mateusz.kozlowski@intel.com>
Change-Id: If0599960f0f872117691c801dce497649da20da6
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468034
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Unify function names and memory handling for create/delete rpc mock
functions in unit test for block zone bdev.
Signed-off-by: Kozlowski Mateusz <mateusz.kozlowski@intel.com>
Change-Id: Ib8613a78623279447cd5a6b9cf0c686e15b69d32
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479644
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Purpose: Prepare for setting priorities for different
kernel based sock implementations.
The g_net_impls list is maintained in decreasing order
according to the priority of each sock implementation.
For examaple, if there are 3 sock implementations, i.e.,
posix (priority = 0), vpp (priority = 1), sock_ut (priority =2),
then the list will be maintained as:
sock_ut -> vpp -> posix.
Then if users use spdk_sock_open/listen with impl_name as NULL,
then the order to try is: sock_ut, vpp, then posix
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I43899de5bac14751ab060a11eb814cd7a0a83cc6
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479488
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Purpose: With this patch,
(1)We can support using different sock implementations in
one application together.
(2)For one IP address managed by kernel, we can use different method
to listen/connect, e.g., posix, or uring. With this patch, we can
designate the specified sock implementation if impl_name is not NULL
and valid. Otherwise, spdk_sock_listen/connect will try to use the sock
implementations in the list by order if impl_name is NULL.
Without this patch, the app will always use the same type of sock implementation
if the order is fixed. For example, if we have posix and uring together,
the first one will always be uring.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Ic49563f5025085471d356798e522ff7ab748f586
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478140
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
A lot of the stubs between these transports will end up being common.
Change-Id: Ib9c8ff947b95f34633eb13953405d3153a7f4ac7
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479602
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This new api function will enable us to work with custom transports.
This is needed to enable properly parsing and comparing custom transport
IDs that may all resolve to the same enum value.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I26aa3cb8f76f8273f564799d9b2af8041ea0d219
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478752
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This function previously accepted a trtype enum, but needs to be able
to accept a string to support custom transports.
Change-Id: I931aed30ca3be65468552ffa1bb1ef3f91275fda
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479601
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For custom transports, we should use a range outside the spec value
to identify them.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I82b29c349e143b8906f79ce2de818def116a3fe4
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478747
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The trtype should be stored as both an enum and string. This is intended to
help pave the way for pluggable NVMe-oF transports.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I6af658d7a17c405e191ff401b80ab704c65497e7
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478744
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
The tests were only built if CONFIG_VHOST was enabled, which doesn't
make sense, as they're not related to vhost in any way.
Change-Id: Idb151b3bdf8c5f2a90357e41099528b10a98f331
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/481505
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
These are unit tests for non emulated version of
spdk_bdev_comparev_blocks function.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I459ac614e1a03e42b9d584aaa907a1448a13d16e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478969
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Upcoming patch will use most of the comparev test code
so let's reuse it.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Ibc6230d38da224bfcf25f76fe1d834d48200bfd9
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479832
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch adds test for spdk_bdev_comparev_blocks
function. For now it tests only emulated compare
operation. For native compare call will be created
separate patch.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Icf2297575f59ab4ee46ba1b40eff6729b3e95b1a
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478948
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is vectored version of test_nvme_ns_cmd_compare_with_md
test.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I8af3a50ae764908024dc2758bb53b119b86edb2c
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478947
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch replaces NVMe Open Channel API usage
inside FTL library with corresponding zone bdev
API calls. This include following calls:
- spdk_nvme_ctrlr_cmd_get_log_page -> spdk_bdev_get_zone_info
- spdk_nvme_ocssd_ns_cmd_vector_reset -> spdk_bdev_zone_management
- spdk_nvme_ns_cmd_read -> spdk_bdev_read_blocks
- spdk_nvme_ns_cmd_write_with_md -> spdk_bdev_write_blocks
Change-Id: I1b5a6863d9ce72f4af1cfbb0e449fc1a5b638144
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479702
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Previously this UT was only checking the snapshot counts.
This was correct, but since the blobs in this tests are
clones of each other - it would make sense to check it as well.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Id9dec7f0a292cbb52da8196bfc77679fc0f49d8b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478976
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
We will only support a vectored variant of
compare-and-write for now.
This does no locking for now. Ii will be added
in a separate patch.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I5bd075c912de60090e19cf8fced19c4879fcc900
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475941
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We can't allow overlapped locked ranges - otherwise
two different channels could be deadlocked.
So add a pending_locked_ranges to the bdev. When we
start a lock operation, check if the new range overlaps
one that's already locked. If so, put it on the pending
list. When an unlock operation completes, we will
check if any pending ranges can now be locked.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I2e3113216a195887b954533495ff200df14fadc1
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478537
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Keep a mutex protected list of the active locked ranges
in the bdev itself. This is only accessed when a new
channel is created, so that it can be populated with
the currently locked ranges.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Id68311b46ad4983b6bc9b0e1a8664d121a7e9f8e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477871
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add an io_locked TAILQ to each channel, which hold
IO that will write to a currently locked region.
Also add a new step to the locking process per channel.
Each channel needs to wait until all existing outstanding
writes to the newly locked range have been completed.
Only the channel that locked an LBA range may submit
write I/O to it. It must use the same cb_arg for the
write I/O as the cb_arg used when locking the LBA range.
This ensures that only the specific I/O operations needing
the lock will bypass the lock.
When a range is unlocked, we will just blindly try to
resubmit all IO in the io_locked tailq. This could be
made more efficient in the future, but we don't expect
this path to occur very often, so going for simplicity
in the first pass.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ibdc992144dfaffe7c05471a5b3c020cedd8cdfc3
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478226
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This adds new internal APIs bdev_lock_lba_range and
bdev_unlock_lba_range. To start, these APIs will
manage dissemination of lock/unlock requests to all
existing channels for a given bdev. This does not
yet interact at all with any I/O sent to the channel.
Future patches will check new I/O to see if they
are trying to write to a range that is locked. Future
patches will also ensure we do not have overlapping
ranges active at once.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I6d5b1cc84b41a7adc2a3c5791c766bb77376581f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478225
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This will be used by upcoming patches for implementing
LBA range locks.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ifa4ad8dcc0d09ccf20d35f010fcae19dcc17abc9
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478224
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
For deletion to actually deliver results, poll_threads()
has to be called.
g_bserrno came from previous API call, not delete itself.
This patch fixes it so that g_bserrno is from the delete itself.
Next patch in series adds checks for number of clones.
Having such checks in first place,
would allow to notice lack of poll_threads() here before.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I3477f5c5b99106b70ee3d5706906a4dc94283180
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478975
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch is part of name refactoring associated
with moving FTL to work with zone bdev API.
Change-Id: Ia4c6ec7b245600bca895f7802fb7f68c8d0400e4
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479845
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This patch is part of name refactoring associated
with moving FTL to work with zone bdev API.
Change-Id: I9e0a569e9dfd0e8b8236c0840ce10b92362c4996
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479844
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This patch is part of name refactoring associated
with moving FTL to work with zone bdev API.
Change-Id: I09f671a9c6539cc259c297514b24978587c9b392
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479673
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This patch is part of name refactoring associated
with moving FTL to work with zone bdev API.
Change-Id: I09781323b2ee25dbcee61eecf95ce7eca703ab93
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479672
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
There is no need of tracking position of zone inside
band.
Change-Id: I1488f23ccfd1f7eee1bd85fdb7ef8ace08ffca40
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468347
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Parallel unit is not needed anymore in ftl_zone
structure.
Change-Id: Ie8d78e3ccf64db84aff19ad2ce11e662d4f3f724
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468345
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Moving to zoned bdev API will not allow to setup
physical range of underlying device so we need to
remove such capabilities from ftl device.
Change-Id: Ia807a11e992a221fce906d4ab122a6c3b1391280
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467949
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
FTL working on top of zoned bdev doesn't need
physical page address (PPA) anymore.
ftl_ppa was replaced with ftl_addr which represents
zoned device addressing schema.
Change-Id: Ied5750a7ab2f4ce42067ff3e69c1f26f85f5022a
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467633
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Remove some Open Channel dependencies from ftl_ppa struct.
Change-Id: Ic088b84c56a928906c6c01c6ef74e69be6d0107f
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479549
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
ftl_ppa address do not need to expose group
information when FTL will move to zones API.
Change-Id: Iece1b32f9bcd8985260668c953089eb9951f13cc
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467603
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
This function was ignored and a little different from others.
Add this to increase code coverage rate.
Signed-off-by: dongx.yi <dongx.yi@intel.com>
Change-Id: I35b51feb8894aca54a3b21436bc21ec12e37adf7
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475814
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Rename stub_submit_request_aligned_buffer function
to stub_submit_request_get_buf and its callback function
to stub_submit_request_get_buf_cb.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Ie8cde43d30c5aa2d353bb33b023d5318948bee44
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478944
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The only reason the qpair ever uses the port is to get to
the device attributes so skip the middle man.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ib14a97ceaa0c49176027d6c35c5cb2787a845cc1
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478961
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add nvme_uevent_ut.c to unittest, and test parse uevents.
Signed-off-by: dongx.yi <dongx.yi@intel.com>
Change-Id: Id8bb8336790ae5e031b357dc49163d86dfa1cd57
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475080
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
UT also added for the block aligned write and verification
of the written data.
Change-Id: I8751f437c71dd7f3a4556fee420460d6dffdd4e5
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478424
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This API will be used in the upcoming reactor_get_stats RPC first.
This API is not public but internal in SPDK. Add necessary unit test
together.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I761ffe3c8d6d8da4594c0d728b479f9f40275fc9
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478024
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Test if spdk_reactor_schedule_thread() scheduled thread correctly
to one of the allowed cores. Use thread library and expect
spdk_reactor_schedule_thread() is called at the end of
spdk_thread_create().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibb536d16849c29081fb63341f5dbe1a4c0db1d18
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478157
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Use the newly added mocks for CPU core operations.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If90bba6fd68c29c83cdb3c201a2a9fbdb40f6755
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478154
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Mock DPDK lcore operations for unit tests. Remove duplicated stup
from unit tests for NVMe-oF FC transport. The next patch will use
them.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4f6fbd8f45942ca13fcf10ba1740a9fe8e573063
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478153
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Extend the unit test of the timeout IO to multi-thread.
Change-Id: I6cd19b629a5f1e473f69685f495fa067a5f5da25
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476052
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Add the protocol_features in vdev. There are two features
would be used in vhost device one is the virtio_features
the other is the vhost-user protocol_features. For different
vhost device, the supported features are different so we can
separate them.
Another reason is that I tested the VHOST_USER_PROTOCOL_F_
INFLIGHT_SHMFD in vhost-scsi with QEMU(version:4.0) and found
that Qemu can not boot up. After investigating found that inflight
flag is negotiated but the Qemu doesn't support this feature
and in DPDK function it is handled as an error and disconnect
with Qemu. It's a bug in DPDK and will fix it.
Change-Id: I72e418cb1885bf7dcbd0285d9cec1ad6af0665de
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478814
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is starting point for moving current FTL
implementation which is working on top of
Open Channel NVMe driver to work on top of
abstracted zoned bdev.
This patch is changing name of ftl_chunk structure
to ftl_zone and start using zone states from zdev
interface.
Change-Id: I5429f489cc08a1ac27f09aba3dca4b40ea95eeb3
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467391
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Add framework and a simple test case to test creating reactor.
Subsequent patches will add more test cases.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ie0eb0e49bfe40469b351b21e40558a1bf5584cce
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478151
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
For the requests which don't have children requests, SPDK may queue them to
the queued_req list due to limited resources, in the completion path, we
may resubmit them to the controller. When the controller was removed
the submission path will return -ENXIO and we will free the requests directly,
so the callback will not be trigerred for these requests. Here we added a
flag to indicate the request is from queued_req list or not, so for the failure
submission, we can triger user's callback.
Fix issue #1097
Change-Id: I901ac81733c2319e540d24baf5b8faa1c649eb35
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477754
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Followin the last patch, move iscsi_conn_abort_queued_datain_task()
and iscsi_conn_abort_queued_datain_tasks() from iscsi.c to conn.c.
Refine unit tests to check more accurately. Adding more test cases
will be done later.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I30530e6871a78a58d9fb472f62168862298884a0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477417
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Added spdk_poller_(pause|resume) that allow a poller to be paused and
then resumed at a later point. These functions come in handy in cases
when a poller is known to be idle until a certain event occurs.
Change-Id: I7f21c80eb9ac4e8e1cf24d66f99da5687aafe358
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477920
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch adds the logic for retrieving chunk notification log and
translating it into media management events to be sent to appropriate
Open Channel bdev.
Change-Id: I7e4860eda23e61d6208fc5f5861e8fd2b75685d3
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471461
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch adds the ability to create bdevs on specified parallel unit
ranges on one OCSSD controller. It allows the user to create multiple
isolated bdevs, each operating on a separate set of parallel units.
To create a bdev on a specified range, a new parameter -r|--range was
added. For example:
rpc.py bdev_ocssd_create -c nvme0 -b nvme0n1 -r 0-4
will create a bdev on parallel units 0 through 4 (inclusive). If the
parameter is ommited, the bdev will span across all available units.
Change-Id: Icd94cf1e22fcc72806ef1ce1efd2d7031010009f
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469898
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
We also need to make sure that the deconm_iov is large enough to handle
all of the iovs we claim to support plus 2, one for offset into the
chunk when doing writes and one for the remainder.
Plus a unittest to demonstrate the possible out of bounds error in the
library.
Change-Id: I7747ad39f76e50f25ecf5168b01e046f71fa0ea8
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478125
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
These buffers weren't actually used, but "buf" is an array,
so we should just pass buf, not &buf.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I9d73a73b138d2bd9c14172c58b1825cf83532b4f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478119
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
With DPDK 19.11 rte_eal_get_configuration() and rte_config
structure were made private. Those were only used in
the inline rte_lcore_count() included from DPDK.
After the update they were no longer available.
Since only rte_lcore_count() was used directly in crypto,
mock that and return 1, as was done previously.
This was tested with DPDK 19.08 and DPDK 19.11.
Change-Id: I13e4d9743b17a34ad786283f8b567d01e036d368
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477841
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This went unused in the unit tests.
Tested with DPDK 19.08 and DPDK 19.11.
Change-Id: I738919379b5751697f9533f72fbaf77993cb6fb5
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477840
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Operations to queue iSCSI tasks are in iscsi.c and conn.c and cross
references due to this separation makes us difficult to create unit
tests.
This and subsequent patches will try to disentangle cross references
by moving some functions from iscsi.c to conn.c.
This patch moves spdk_iscsi_conn_handle_queued_datain_tasks() from
iscsi.c to conn.c. For unit tests, we don't add anything new in
this patch and just create necessary simple stubs. After code
movement, new unit tests will be added.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If5b8501a1ef7ea53682a3437c7eb2375aa52ee3b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477416
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Subsequent patches will change trace functions to be called in
unit tests. Using stubs is enough as done in other libraries
and do the change in this patch. For iscsi_ut.c, add stubs to
not iscsi_ut.c but common.c to cover other files.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ia14bc932f451b14bdb0ba6e0cb949463490a879e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477414
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Using "={}" at definition is clearer and saves lines.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I75a99583f1ecc84d4c47cacd9ce58034edb4e756
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477413
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Using "= {} at definition is clearer and save lines.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I410279bd3640e03aa9b6eeb488be4404d110b0bd
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477412
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
If a spdk_bdev_io cannot be completed, because it is sent to a zone that
is currently busy, reschedule its submission. This mechanism will be
used by appends, as mutliple append commands can be directed to the same
zone at the same time.
Change-Id: I60da2bd1835380812d22536ea275fb8fed9f8561
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477437
Reviewed-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch adds support for saving JSON configuration of the OCSSD
bdev module required to recreate the current state.
Change-Id: Iedbdb8b4a2b7dd02a223ce6f073553e71b9c040a
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469090
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
OCSSD bdev needs to keep track of some portion of zone's state (write
pointer, its capacity, whether it's busy) in order to support the append
operation. To achieve that, all the info needs to be retrieved for all
of the chunks and translated to zone format.
Change-Id: Id88282576aba337b50e7c7e1b9e9ff5aba25a3db
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468937
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Added zone information command translating Open Channel's chunk
information to spdk_bdev_zone_info structure.
Change-Id: Ifdb15f2e0ea2fb8422810fa64f18942fcb6e4582
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468213
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Added zone reset command. It's very similar to a regular data set
management deallocate command with the only difference being that it
operates on zones instead of blocks.
Change-Id: Iae4d77c6877b6906231336b13fad1167de149f20
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467920
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
This eliminates the flushing logic, simplifying the tcp
transport.
This also happens to greatly improve performance, especially
on random read tests. The batching done in spdk_sock_writev_async seems
to be more effectively than the previous batching logic in the tcp
transport.
Change-Id: Id980ac6073e380dc75f95df3f69cb224f50fb01b
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470532
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is preparation to add flags to the call.
Change-Id: I36109c069b42bd3ec22e023079c62d41a435f44c
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471771
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Add an additional queue for requests that have been sent on the network
but aren't complete yet. As of this patch, the code
is still calling writev with no flags in the POSIX layer, so it completes
synchronously. That means requests pass through this new pending list
only very briefly inside of one function.
Change-Id: Iaab6efc118a6d5fe9589199515eb3a7293db4b8e
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471768
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Or Gerlitz <gerlitz.or@gmail.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add spdk_sock_writev_async for performing asynchronous writes to
sockets. The user of this call is responsible for allocating their own
spdk_sock_request structures to pass to this call.
spdk_sock_writev_async will not return EAGAIN and will instead leave the
requests queued until they are fully sent or aborted due to socket
error.
Change-Id: Idf3239e65d26a3024e578122c23e4fb8f95e241b
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470523
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add the unit test to verify the submitted list,
timeout IO poller and timeout IO check.
Change-Id: Ie7832cc29e19a624328a1a96cffe313bf9f18a69
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476051
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
The macro DMIN32/64() are local in iscsi.c. Replace them by the
generic macro spdk_min() will improve the portability.
Replace it in test/unit/lib/iscsi/conn.c/conn_ut.c together.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5f6992b3dc091cd748b4e138810fb01761a1ab24
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477202
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
spdk_iscsi_is_deferred_free_pdu() is called only in a single
place of conn.c. So change it to private in conn.c. Additionally,
iscsi_is_free_pdu()_deferred() may be a little more meaningful
and rename to it.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ic1e3d7ff435c454f40e81f9a4f90fe76589ec7b2
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477189
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Re-order operations in abort_queued_datain_task_test() to align it
with comment, and fix a type error.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Idde4726bfe370ad742b2de67e0786aebb7237d45
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/477409
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
We changed read I/O submission to stop splitting when detecting LUN
hotplug very recently. We can do the same refinement for read I/O
abortion.
In _iscsi_conn_abort_queued_datain_task(), set all remaining length
to the new task and complete it immediately. We keep the code to
process the case that queued_datain_task completed but is still in
queue, but we can change its if condition to assert.
Simplify the corresponding unit tests accordingly, and set
task->scsi.transfer_len in abort_queued_datain_tasks_test() to
exercise the changed paths.
In iscsi_pdu_payload_po_scsi_read(), if task->scsi.transfer_len is not
larger than SPDK_BDEV_LARGE_BUF_MAX_SIZE, no minimum calculation is
necessary and we can substitute task->scsi.transfer_len to
task->scsi.length simply. This change is too small to be an independent
patch and is done together.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iea93e51b103eae141a007a0abdaf13cbe6d5287f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476984
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
The hardware sgl format can describe large contiguous
buffers using just a single element, so it's more
efficient that a prp list even for a single memory
segment. Always use the sgl format.
Change-Id: I9c62582829f0d64dcd1babdbc48930ddb4d9e626
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475542
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch is used to test the pending buffer policy
of nvme request which has incapsule data. When
group->pending_buff queue not null , we should make
sure spdk_nvmf_tcp_capsule_cmd_hdr_handle method still
can handle the request.
relate to : issues/995
We try to simulate the following manner: If there
is req waiting for the buffer in the list, the
nvme request which has incapsule data will be
handled firstly even it is added into the
pending_buf_queue. The reason is that currently,
those command will get the buffer from its own queue.
We made these test steps:
1. submit a tcp request into spdk_nvmf_tcp_req_process
and make sure it pause in group->pending_buff queue
2. submit a incapsule tcp request into
spdk_nvmf_tcp_capsule_cmd_hdr_handle method , and
this method will call the spdk_nvmf_tcp_req_process
method to handle this request.
3. check whether the incapsule tcp request is handled
correctly. and check the group->pending_buff queue
remain.
Signed-off-by: jiaqizho <jiaqi.zhou@intel.com>
Change-Id: I85fcbb49e309e1203b4b308115e3bfefc0fcba2a
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472665
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The nvme_transport_ctrlr_scan() may return failure while there are
multiple controllers, so the probe context's init_ctrlrs list may
not null for this case, so when free the probe context, let's ensure
there is no controller in the init_ctrlrs list. Also added a UT to
cover this case.
Fix issue #1095.
Change-Id: I4d9a10ad73cf00bbe159edd1f5b919797333feb6
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476969
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
nvme_qpair_get_state fits more closely with the semantics in other
modules.
Change-Id: I6ea8e02abe27253d9b4d779a43ac1963be56356a
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476920
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
The qpair state transport_qpair_is_failed is actually equivalent to
NVME_QPAIR_IS_CONNECTED in the qpair state machine.
There are a couple of places where we check against
transport_qp_is_failed and then immediately check to see if we are in
the connected state. If we are failed, or we are not in the connected
state we return the same value to the calling function.
Since the checks for transport_qpair_is_failed are not necessary, they
can be removed. As a result, there is no need to keep track of it and it
can be removed from the qpair structure.
Change-Id: I4aef5d20eb267bfd6118e5d1d088df05574d9ffd
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475802
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
CPU mask parameter was deprecated in v19.10.
If we remove the related code from the portal parser, we will be
able to use the parser for the iSCSI initiator to know the target
portal in iSCSI fuzz testing. So let's remove the parser and its
test code here.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I72ad4364323abda0f0ed10519b56244cd0c7612e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476830
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
The patch adds zone address to Open Channel LBA translation as well as
initial support for read and write commands. Each IO command is
currently limited to a single zone (chunk).
Change-Id: I3ee6d58323871f0651ac1d5e8dda28eb6d687a95
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467149
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Added a way to create and delete OCSSD bdevs on top of OC NVMe
controller. The controller can be created using the regular NVMe bdev
RPC call. For instance, the following (assuming 0000:00:04.0 is an
OC device):
rpc.py bdev_nvme_attach_controller -b nvme0 -a 0000:00:04.0 -t pcie
rpc.py bdev_ocssd_create -c nvme0 -b nvme0n1
creates Open Channel controller nvme0 and OCSSD bdev nvme0n1 on top of
it. The bdevs can be deleted either by the bdev_ocssd_delete call or by
deleting whole NVMe controller, in which case all bdevs are destroyed.
Change-Id: I9f2f02103fc5570a53bd26479c8690be206829c3
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468984
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add coverage to the path where we dequeue multiple ops for a
bdev_io and one of them has failed. Confirm that the bdev_io
gets failed.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ie864b63819f506da43fdcad960c26a48a01196c7
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472417
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
A recent change in the CryptoDev API means that failure to enqueue
all attempted submissions does not automtically mean busy. We need
to check the status of the last submitted op and only retry if
busy, otherwise fail the IO.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I0873d07a430a08f5aee25581e47187ef60ba8542
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472400
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Previously we would sit in the submission routine and spin on the
poller and then retry in the event that we could not get CryptoDev
to take all of the ops that we had available.
The implementation was fine however a recent CryptoDev change
requires us to now check the status of attempted submissions
instead of assuming that the device was busy. If there was
another reason for the failure we don't want to retry or we'll
be stuck in an endless retry loop.
Changing the current device full handling to match what was
done in the compression vbdev makes it easier to handle the
new condition and also makes the two vbdevs more consistent
with regards to how they manage the DPDK framework API.
This patch only changes how we handle full conditions to put
the ops on a linked list and resubmit them the next tie the
poller runs naturally. A following patch will handle the
CryptoDev API change that instigated this change.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Idcb6e06b6826045f23e59b64eca051f3eee2b850
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472309
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
iscsi_conn_free_task() is used only when exiting connection now.
Hence we can remove the parameter lun and simplify the function
and its unit tests.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6e7bf09672edca1f70c042ac58f098114d71ec78
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476115
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
In _iscsi_conn_free_tasks(), we had parsed conn->write_pdu_list
and then parsed conn->queued_datain_tasks. However when we parsed
conn->write_pdu_list, if there was any task in conn->queued_datain_tasks,
some PDUs were inserted conn->write_pdu_list. Hence after parsing
conn->write_pdu_list, new PDUs were in conn->write_pdu_list as orphan.
Then orphaned PDUs were freed later but LUN was already freed and
critical failure occurred.
This patch swaps the order of conn->queued_datain_tasks and
conn->write_pdu_list, and add comment to explain the change.
Additionally, this patch adds unit test which fails if it runs
without this fix.
Fixes issue #1030.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Icb0ffbbbac70792a62939dc55a69df05d2ab9128
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475453
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
When a iSCSI write is large and split, if LUN is removed between
creating and submitting the last subtask, spdk_clear_all_transfer_task()
completes the primary task and then process_non_read_task_completion()
tries to complete the primary task.
This is the double free case, and the later have to be skipped.
We add a flag is_r2t_active to struct spdk_iscsi_task and use it to
check the duplication. We may be able to use primary's initiator task tag
(ITT) instead but we can not rely on ITT because it is set by the initiator.
We clear is_r2t_active even when primary is removed from
conn->queued_r2t_tasks but it will be no harm.
Fixes the issue #1064.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ia6511bd7adaa8fcb9a07bc40d498e8ee0b7a7ccf
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475044
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
To improve the value of unit tests, this patch adds task hierarchy
and update and check of reference count to unit tests.
Besides, replace memset by initialization at definition to reduce
number of lines.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Id8315faeb8f5a62f621b7c41a30c1d09aca4ae0e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476032
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The type of pdu deferred to be free only have
two types, R2T or DATA_IN. And the two types of pdus
are all assoicated a task, so updateing both the code and unit test case.
Also for all pdu free, we should use spdk_iscsi_conn_free function since
for normal pdu free, we all use this function.
PS: I also tested the calsoft local, it does not trigger the assert.
Fixes#1074.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I0524965baf5349a100210ef717aedaa5f8ff105e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475657
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Purpose: Simply the code, doing data_cnt_in every where
will make the code diffcult to maintain. If we put the
management in iscsi task get and free related function, then
the code will be easy to be read and easy to maintain.
Change-Id: Ib9af067326630657877a94afc2eb0db28f5d5fd1
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/474914
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Purpose: Do not let the primary task do the I/O if it is
splitted into subtasks. This will make the code simplier,
when all the sub I/Os are finished, we can free the
primary task.
Update the corresponding unit test also.
As a result of this change, when read I/O is split into subtasks,
the primary task uses only some of its data. Hence separate
iscsi_pdu_payload_op_scsi_read() into split and non-split
case explicitly.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I9bbe4b8dd92a2996f35ad810b33676e34670c77e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473532
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is a workaround for issue #1083.
Using constructing nvme_pcie_ctrlr to access spdk_nvme_ctrlr,
this avoid reporting :
Memory access at offset * overflows this variable.
Signed-off-by: dongx.yi <dongx.yi@intel.com>
Change-Id: Ided625f95ff33df277c28e0410e946f99b787550
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/476420
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: JinYu <jin.yu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
This was an old set of unit tests that was commented out. It's now
hopelessly out of date, so remove it. The rest of this series will
add in equivalent tests that work on the new code.
Change-Id: Ib74072c7a9156647ecff9ebd76997d46fec3c0cf
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475776
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This patch fixes minor unit test deallocations around io_channels.
It has not exposed any issues in blobstore code, but should always be right
to prevent covering up any issues later.
1) Two spdk_bs_free_io_channel() were missing
2) Dirty shutdown should still free bs resources with _spdk_bs_free()
Sample log at the end of UT, before this patch:
thread.c: 200:_free_thread: *ERROR*: thread 0x617000000080 still has channel for io_device blobstore
thread.c: 200:_free_thread: *ERROR*: thread 0x617000000080 still has channel for io_device blobstore
thread.c: 200:_free_thread: *ERROR*: thread 0x617000000080 still has channel for io_device blobstore
thread.c: 180:spdk_thread_lib_fini: *ERROR*: io_device blobstore not unregistered
thread.c: 180:spdk_thread_lib_fini: *ERROR*: io_device blobstore not unregistered
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I187bc61bb6e094c9c740a987e7d14760551a0503
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475872
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Previously blob_insert_cluster_msg UT specified the cluster
which will be used to store LBA. So for blob the cluster [1],
was always stored as cluster 0xF in blobstore.
This patch changes _spdk_bs_claim_cluster() with preselected
cluster in blobstore to _spdk_bs_allocate_cluster() that
will choose first free one in the map.
It will help in further patches that add more logic
on extent table and extent pages in _spdk_bs_allocate_cluster().
Otherwise this patch 'hard coded' values might get more complex
than needed.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I238329b2191e7ebd3f73c1fe85d7e1da0249979e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475493
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
When serializing extents, run-length encoding is supposed to
1) RLE all sequential LBAs
2) RLE zero LBAs (unallocated)
There is one special case, with sequential LBAs that start
with 0 LBA. This is RLE as 1) case, but results in descriptor
matching case 2). Which causes loss of allocated clusters.
This requires following conditions to be met:
- blobstore has just a single cluster reserved for MD
- blob is thin provisioned
- first allocation occurs on cluster_num=1
For last part to be true, very first write for blob has to be
issued to LBA between cluster_size and 2*cluster_size.
Causing allocation of second cluster in blobstore and assiging
it LBA equal to number of LBAs per cluster.
To fix this, case 1) disallows to RLE zeroes.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I136282407966310c882ca97c960e9a71c442c469
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475494
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There is a sleep in a test to allow a socket close to
propagate through the kernel stack. This is only required
on FreeBSD, so limit it's use to FreeBSD.
This results in slightly faster unit test run times on Linux.
Change-Id: I495d8b91e7247d0757650c4993d18f707c524a22
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475312
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Added states for keeping track on which reloc
queue band actually is.
Change-Id: Ib05ac4e925002728ddfed3195891f5328eebb0d0
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465072
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
After recent refinement of LUN hotplug, it is possible that
for large write I/O, primary task is freed doubly as a github issue
is reported.
However we could not notice the case because spdk_del_transfer_task()
had not return success/failure, and to make matters worse,
the second call of TAILQ_REMOVE() to the same header and instance
caused no error if the first call succeeded.
This patch changes spdk_del_transfer_task() to return success/failure.
Besides, the next after patch expects the stub of spdk_del_transfer_task()
returns true in the unit test, and hence do that.
The next after patch will fix the issue of double free of primary task
by using this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibc0b65723050362d5fafa913417b64393feb874e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475042
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
By the recent refactoring, SCSI task is configured when getting
DIF context from SCSI layer. Passing not CDB and offset separately
but SCSI task to SCSI layer is more concise and do in this patch.
In iscsi_send_datain(), we have to update task->scsi.offset for the
case that data is split into a sequence, but the update is no harm
because task has completed what it must to do.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I153352dfa7aa7325db4452f03d863df11b3e0cfa
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472510
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Like memcpy, but works on two iovecs.
Change-Id: Ia1cf462a95690286f0c19325fc10937b9ba6baf3
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473976
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
When dealing with sockets most code in SPDK buffers
data into large chunks to minimize the number of
syscalls made. The pipe utility is designed to make
that easy.
Change-Id: Ie29966712bbfb43fb49457e042903cf45864e6c6
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465707
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The _ was supposed to indicate an internal function,
but really leaving off the spdk in the function
is the standard way to denote an internal function.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I74facafb67b793502838b9c1b5f90aec2c88c69b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475033
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
We try to reserve the spdk_ prefix for functions that
are part of the public SPDK API.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I0a95ba0f9db04b588a2e948427f8a9f53a7b5740
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475032
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This function is not part of the SPDK public API, so
remove the spdk_ prefix from it to make it more clear
this is internal to the SPDK bdev library.
Also add "channel" to the name since this function is
operating on the channel parameter.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I57897ab4bf601b90551259b7cf6efa63152ed02f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475031
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This is not part of the public SPDK API, so remove
the spdk_ prefix to make it clear this is internal
to the bdev library.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ibda76e4d8e34dde0c2fe638cb965e5ba2d9e47b5
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475030
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
This function is not part of the SPDK public API, so
remove the spdk_ prefix to make that more clear when
reading the code.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I5ea4c04c474a6cf0862f11921daa97c9df728e96
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/475029
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
This patch introduces indirection layer for session management
functions that makes it possible to switch their underlying implementation
if we want to (in unit tests for example).
Change-Id: I563c97bc65d55cc42fecbd1b7eb6679e394784a2
Signed-off-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470459
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
rte_vhost_compat.c will now not only handle vhost-user
messages over the unix domain socket, but also setup
that unix domain socket with rte_vhost's APIs.
What was previously called vhost_dev_install_rte_compat_hooks()
is now called vhost_register_unix_socket() and is responsible
for creating the entire unix domain socket.
This enables us to write more advanced unit tests for vhost.
Instead of mocking low-level rte_vhost APIs, we could
now potentially mock vhost_register_unix_socket() and
create vhost devices and sessions without any actual
unix domain sockets involved.
Change-Id: Ifb18b92b37915c3f683b6d4fcdcc9259a3770561
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Signed-off-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470455
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Read task completion has been factored out into
process_read_task_completion(). Factoring out non-read task completion
into process_non_read_task_completion() makes the code a little
clearer and makes us possible to add unit tests.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4da3cd05fc3668d0db4436301e4bcb1b554de7cd
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472905
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
iSCSI target frees iSCSI tasks when exiting connection or removing
LUN. The difference is only that the passed LUN is NULL or not.
To make the code clearer, this patch factors out freeing iSCSI
tasks from iscsi_conn_free_tasks() and _iscsi_conn_remove_lun()
into _iscsi_conn_free_tasks().
The refactoring has subtle cases and so add UT code together.
The next patch will fix the issue that secondary tasks are left
even after primary tasks are freed when exiting connection or
removing LUN, and this patch clarifies the next patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I18aaed6fe18a1c561ac88a0e5dc1296f9941d0e8
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473154
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Shellcheck version 0.6.0 reports all instances where we cd .. or cd - as
instances of SC2103. The version we are using on the test pool must be
newer, because we don't get the same errors, but for people running
check_format locally, it can make it difficult to parse the output.
Change-Id: I09f81a83c6f37480f13c36eb622e500364a1c437
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/474150
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Out-of-order case didn't have UT code. Besides, remove unnecessary
if check in the in-order case together.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ic3c09de73f57033a1db9522519347d7d201e38be
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473255
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
We have separated PDU header handler and payload handler, and have
PDU header handlers for each PDU type now.
By using this refinement, we can remove an aggregated helper function
spdk_iscsi_get_dif_ctx() and embed spdk_scsi_lun_get_dif_ctx() into
each PDU header handler.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ib4d9939b625858466224647c545cb67a04babf86
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471699
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Add unit tests for PDU header handling except for SNACK Request PDU
because the caes that Error Recovery Level is not matured yet.
The purpose is mainly for increasing coverage, and most were reviewed
separately, and so merge multiple PDU types into a single patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ice8c522bee0fc8c0dadb0c6326be9f65d323d52e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471955
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add registration and unregistration of block zoned bdev. Attach it to the
underlying bdev during creation and unattach at deletion.
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: I773aff6c7609952f28c02dd1794f0529a781b2e1
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468033
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
We should alert the upper layer when the qpair becomes unusable due to
qpair errors.
Change-Id: Icdee3b55a14441a60111f3bd7a44dceef93bbb09
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/474095
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
SCSI management task is for SCSI tasks which is submitted after it,
and all such SCSI tasks are aborted by the last patch when we
remove LUN dynamically. Hence we can abort all SCSI management tasks
being queued when removing LUN.
Add simple unit tests too.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9be3f910ab4bbb99cd399f71dc716a7c40f34fe5
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/474022
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This clarifies that g_write_pdu_list is global.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4292a2fb455f3a47d79ae6ebb5dc6046f0f7dd52
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471951
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This memory leak bug is very easy to reproduce.
You can follow this step to reproduce:
1. clone master spdk , update submoudle
2. ./configure --with-fuse && make -j24
3. valgrind --leak-check=full --error-exitcode=2
test/unit/lib/blobfs/blobfs_bdev.c/blobfs_bdev_ut
It show the memory when you run valgrind.
This is because the ctx in spdk_blobfs_bdev_mount have
not freed when spdk_fs_load(override in blobfs_bdev_ut)
passed.
So i added a unmount operation after mount operation
to fix this problem.
Signed-off-by: jiaqizho <jiaqi.zhou@intel.com>
Change-Id: I770f914123e353dc42d0420c1fb8b34ebdf88f6c
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473171
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Currently we have a mix of -1 and -EINVAL which
is confusing, especially since these types of failures
also result in the caller's callback routine getting
invoked.
While here, document this new -EFAULT return code for
all of the functions that could return it.
Fixes issue #797.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I8dfbba0ec0b83db0f2ec055b15830981af1965df
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473054
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This at least allows the caller to know there was a
problem, and that the messages wasn't actually sent.
SPDK by default creates huge rings so this problem
should never occur, but out-of-tree use cases may
send messages much more often and require at least
a notification when it fails.
While here, change the thread check to an assert.
There's no need to work around someone calling
this function with a null thread parameter.
Fixes issue #811.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ie6d432d616be45c7a4232aff1548cef198702bc0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472438
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
A recent change to the compression API means that we can no longer
assume that rejection from the API means that it was busy. We need
to only queue operations that were from the busy condition and
fail others.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I7fa5d27559eacdf1bdf6982bdc142939333076ae
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472465
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This reverts commit 0b9931516d.
"cd $dir && ..." in single line does switch directory for
the following commands.
The patch being reverted, broke the nightly (autopackage.sh) tests.
It was only fixing couple of instances of SC2164,
which is being excluded either way.
https://github.com/koalaman/shellcheck/wiki/SC2164
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Id4f134ad98953b92fdc69cd0d0b80c02660cf7a9
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/473220
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Don't change the directory of the script if at all possible.
Change-Id: I5e20784694cb61fac2cf148628de566361e2673e
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472650
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Also add functions to convert it to/from string.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Change-Id: I6f7964d832c308b815150fff39eb3dc5c5ae5853
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471079
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Disconnecting qpairs from the admin thread during a reset led to an
inevitable race with the data thread. QP related memory is freed during
the disconnect and cannot be touched from the other threads.
The only way to fix this is to force the qpair disconnect onto the
data thread.
This requires a small change in the way that resets are handled for
pcie. Please see the code in reset.c for that change.
fixes: bb01a089
Change-Id: I8a39e444c7cbbe85fafca42ffd040e929721ce95
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472749
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch allows to send IO requests from external module to the nvme
device.
External module should call nvme_io_msg_ctrlr_start() to start IO message
producer on the controller and enable sending messages.
nvme_io_msg_send() is used to send IO to NVMe driver thread context,
where passed function will be called. Allowing the external module to
issue IO as needed.
NVMe driver users should poll spdk_nvme_io_msg_process() to move forward,
sending IO from external module and process their completions.
Change-Id: Ie59abac69870c4e4daa50120c747f3b620395921
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471386
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This change allows setting of the NVMe completion queue
CDW0 in spdk_bdev_io_complete_nvme_status.
Before that change, handling of vendor specific NVMe IO
commands was limited since there wasn't a way to return
command specific info back to the initiator.
Change-Id: I250d5df3bd1e62ddb89a011503d42bd4c8390f9b
Signed-off-by: Michael Haeuptle <michael.haeuptle@hpe.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470678
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This can be useful when trying to perform multipath failover at the
application level. However, the controller must be in the failed state
before calling this function.
Change-Id: I5403c0036fed5dd3600ee20592925297494ba8aa
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470699
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
While it is unlikely that a single qpair will be failed, it is important
to make it possible to reconnect a single qpair.
This function is also handy at the application layer when going through
a reconnect workflow. If we get -ENXIO from a qpair when we poll, we
will turn around and call this function. If we get -ENXIO from this
function, then we know the whole controller is failed and we need to do
a reset.
Change-Id: I6a8ea0ce27fce2f5fc0a5b3db05834acd68e6a39
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471417
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
When splitting bdev's, if we run out of child IOVs, we have to
make sure that we end block aligned. That may require us to
shorten or eliminate one or more child IOVs to be picked up
on the next split. If we eliminate enough such that there
are no IOVs for this split IO, just continue and the next
split completion will kick off another split to pick up
the remaining data to be transferred.
Fixes issue #981
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: If2bfbe5f0862295e1d74cbea00692890a2178967
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471313
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
These will form the base of a little state machine for managing the nvme
qpair structure.
Change-Id: If6f6df38cc17221ac8fcb7d8c0d7e2e808897a99
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470534
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The driver has historically waited until we have to do a listen
before enabling the admin qpair. That is a very PCIe-centric mindset.
For fabric controllers, a lot of the early initialization operations such
as get_cc and set_cc are handled through the admin qpair so it should be
enabled before we begin the initialization process.
As a side effect of this cahnge, the internal API
nvme_ctrlr_enable_admin_qpair has been removed. It would have turned
into a one-liner.
Change-Id: Icd162657d01a85c227a3f20c295d0208e07ce44d
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471743
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Extract PDU header handling from PDU payload handling for all PDU
types, and then group them into a new function iscsi_pdu_hdr_handle().
Then the original iscsi_execute() is renamed to iscsi_pdu_payload_handle().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I1fb1937cfaf502797f2c4edb3aeeb97d4697c7d4
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471015
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previously, for iSCSI target, freeing bdev_io of SCSI task was deferred
until the reference count of the SCSI task becomes zero.
But this will cause the use-after-free issue when doing LUN hotplug during
large write I/O workload.
The scenario is the following:
- Large iSCSI write I/O is split into multiple I/Os, the first I/O is from immediate,
and subsetquent I/Os are from R2T.
1. The first I/O allocates iSCSI task as primary, and is submitted to the bdev layer.
The first I/O is pending in the bdev layer.
2. The second I/O allocates iSCSI task as secondary (secondary is associated with
primary by incrementing reference count).
3. Before submitting the second I/O to the bdev layer, LUN hotplug is started.
LUN hotplug waits for getting completion of the first write I/O from the bdev layer.
4. The bdev layer completes the first I/O. The primary iSCSI task is tried to free,
but reference count is still one, and is not done yet.
5. LUN hotplug detects completion of the first write I/O, and returns
LUN I/O channel to the bdev layer.
6. The second I/O is tried to submit to the bdev layer, but LUN is already removed,
and so free the secondary iSCSI task.
7. Then the reference count of the primary iSCSI task becomes zero,
and its bdev_io is freed. However, LUN I/O channel is already freed and freeing
bdev_io fails.
This issue is caused by separating iSCSI task allocation and submission.
For write I/O, we don't have to keep bdev_io after getting completion
of it from the bdev layer.
This applies to other non-read I/O types.
So for non-read I/O, free bdev_io after getting SCSI status in
bdev_scsi_task_complete_cmd(), and for read I/O, set bdev_io to
task as same as before.
The next patch will do the same for management task.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I530fb491514880ce41858e1bea55d422d606dfc4
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471695
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Refine the public helper function spdk_scsi_dev_has_pending_tasks to
be able to check tasks only from the specific initiator.
Then use the function in iSCSI target to fix the issue.
Besides add UT code to test the updated spdk_scsi_dev_has_pending_tasks().
Automated multi hosts test is much better but some UT code will be of any
help to mitigate the risk of degradation.
Fixes#985
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I50afb940de7174360c8a30479450850002a3e525
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471337
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Refine helper functions spdk_scsi_lun_has_pending_mgmt_tasks() and
spdk_scsi_lun_has_pending_tasks() to be able to check tasks only from the
specific initiator.
SCSI port is used by passing the pointer and so simple pointer
comparison is appropriate in the functions.
Add UT code to test the updated functions.
The next patch will change spdk_scsi_dev_has_pending_tasks() to
get not only SCSI device but also initiator port and make iSCSI
target use the function to fix the issue.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I89c33e05bc6ab21baa6cbebf60950039a3dcecd0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471336
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
It can be useful for passing additional information about nvmf
target to a handler for new nvmf connections. Context can be
stored in globals as it is currently done in nvmf code. However
in case of multiple targets or languages where accessing global
state is challenging (i.e. Rust), this becomes inconvenient.
Change-Id: Ia6a2fdba4601531822b3e5fda7ac5ab89d46f6c5
Signed-off-by: Jan Kryl <jan.kryl@mayadata.io>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469263
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Sasha Kotchubievsky <sashakot@mellanox.com>
To make the code clearer,
- make the spdk_iscsi_read_pdu() private in iscsi.c and named iscsi_read_pdu(), and
- make the iscsi_conn_handle_incoming_pdus() public and named
spdk_iscsi_handle_incoming_pdus().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I967681b8e9b86681a906b18719e91e1d387450d7
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469969
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is useful for detecting sockets that have been disconnected
by the other end without reading data.
Change-Id: Ieb6529984d282d48373766d9f5555cf11720f19b
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470513
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
FUSE operations in blobfs_fuse.c are extracted from
test/blobfs/fuse/fuse.c to blobfs_fuse.c in module blobfs_bdev.
And it is extended to create one new thread dedicatedly for one
FUSE mountpoint to handle FUSE requests by blobfs sync API.
spdk_blobfs_bdev_mount is implemented as the export API. So
related code can be utilized by other modules/apps.
Now test/blobfs/fuse/fuse.c is much simplified with function
spdk_blobfs_bdev_mount.
Change-Id: Iefa16977fabbae2008c8f65fe1b69d650b6fd18d
Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469347
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Move spdk_iscsi_execute() from iscsi_conn_handle_incoming_pdus()
to spdk_iscsi_read_pdu() and then strip the prefix spdk_ from
spdk_iscsi_execute() and make it private.
This is to introduce state machine into receive incoming PDU processing.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5d5b3e55ece0994532e924d3c75d898cb373875c
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470287
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
In-capsule data transfer can only be supported by NVME drives with SGL memory layout
Add test to examine new behaviour
Change-Id: Iaef6564c8e5c96c1c5af16ab41d6e3827f6a82b6
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Sasha Kotchubievsky <sashakot@mellanox.com>
Signed-off-by: Evgenii Kochetov <evgeniik@mellanox.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470469
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
When we ran out of child_iov space, ensure the iovs to be aligned
with block size. However the calculation was wrong.
(to_next_boundary_bytes % blocklen) meant not to_last_block but to_next_block.
So calculate to_last_block_size by reducing to_last_block_size from blocklen.
The data was collected when the issue occured. So add unit test
by using the data.
Fixes#979
Reported-by: Geoffrey McRae <geoff@hostfission.com>
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I62a50bada450288ea7c60aec0e557c2a53cd8916
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470806
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This function has not been tested, add test in nvme_ctrlr_cmd_ut.c
to increase code coverage rate.
Change-Id: Ibe5c98924d9e2f3239d782e7a32b828caaddb04a
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470718
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Following test/blobfs/mkfs case, add it as one RPC
method to let build a new blobfs on given block
device.
Change-Id: I0ffbb1add95dfbc8655e0238ed6f3cd519dd945b
Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466485
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Add module blobfs_bdev as a general module to simplify
the operations of blobfs on bdev. Then its functions
can be utilized by other libraries or apps.
blobfs_detect can be used to detect whether there is
one blobfs on given bdev.
Change-Id: Ib425574816061dc945fb652b539f791a44097a43
Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466486
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Request logout to the initiator asynchronously when exiting the
running connection from the target.
Based on this patch, the next patch will make flushing PDUs possible
only when the connection is RUNNING (or INVALID) and remove the
tight loop in iscsi_conn_flush_pdus().
Set timeout of logout request as 30 seconds. 30 seconds is as same as
NOP timeout and will be reasonable for now.
Add and use logout_request_timer to check the timeout.
When the connection gets internal a logout request, move the connection
to EXITING state if the connection is in INVALID state, request logout
to initiator and start 30 seconds timer if the connection is in RUNNING
state and logout is not requested yet, or do nothing otherwise.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I43192be9fd7112ad444152c0dd88f99a14aa8d30
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470705
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
If we are to have multiple reconnect attempts, we have to control
whetehr the controller is placed in the failed state from outside the
reset function itself. This will allow us to fail the controller only
after all of our retries are exhausted.
Change-Id: Ia82e10325272f25b2b8527336dc3bc507c93b401
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469932
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Use the standard API function to fail the controller in all cases.
This patch, and the several following patches are aimed at creating a
mechanism for reporting up to the application layer that a controller is
failed and or removed. To do this, I use the reset_cb to inform the
upper layer that the controller is failed.
This also requires changes to how we handle a controller reset to
pave the way for doing optional reset retries in the libraries.
Change-Id: I06dfce08326c23472a1caa8f6efbac2fd1a720f2
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469635
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Next commits in the series will need these callbacks in other tests
that are closer to the beginning of file.
Signed-off-by: Evgeniy Kochetov <evgeniik@mellanox.com>
Signed-off-by: Sasha Kotchubievsky <sashakot@mellanox.com>
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I55e346f273f169c7894f662dcfa1f57a02024577
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469708
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Have each sock implementation free the group_impl itself.
This allows C++ based sock implementations like Seastar
to release the group_impl memory using delete rather
than free.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: If40a91e8bc93a531701fc30d847ab28fa11858ab
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469618
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We can merge two loops of req->buffers and req->iov into a single
loop and merge two variables, req->num_buffers and req->iovcnt into
a single variable. For the latter, use req->iovcnt because it is
also used for in-capsule data.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ia164f2054b98bbcb00308791774e3ffa4fc70baf
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469489
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This follows the good practice of FC transport.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I84a6bb28a27b529335f100c8cab12d642bc156ff
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469488
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch is the end of the effort to unify buffer allocation
among NVMe-oF transports.
This patch aggregates multiple calls of spdk_nvmf_request_get_buffers()
into a single spdk_nvmf_request_get_buffers_multi().
As a side effect, we can move zeroing req->iovcnt into
spdk_nvmf_request_get_buffers() and spdk_nvmf_request_get_buffers_multi()
and do it in this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I728bd330a1f533019957d58e06831a79fc17e382
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469206
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch is close to the end of the effort to unify buffer allocation
among NVMe-oF transports.
Merge each transport's fill_buffers() into common
spdk_nvmf_request_get_buffers() of the generic NVMe-oF transport.
One noticeable change is to set req->data_from_pool to true not in
each specific transport but in the generic transport.
The next patch will add spdk_nvmf_request_get_multi_buffers() for
multi SGL case of RDMA transport.
This relatively long patch series is a preparation to support
zcopy APIs in NVMe-oF target.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Icb04e3a1fa4f5a360b1b26d2ab7c67606ca7c9a0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469205
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Small cleanup in prep for future RAID levels and to improve
readability.
Change-Id: I66ae64320593ee5b242ccdc50a0041a4ec8207fb
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/469742
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9fb7a998f7c13ce53cba630a895e8e11cf5f4a1c
Signed-off-by: Benjamin Saunders <bsaunders@google.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467559
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The subsequent patches unifies getting buffers, filling iovecs, and
filling WRs in a single API. This is a preparation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I077c4ea8957dcb3c7e4f4181f18b04b343e9927d
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468953
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
This patch makes multi SGL case possible to call spdk_nvmf_request_get_buffers()
per WR.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I977ebb0c6b2a67218c9b6fc20dc26a93a6ec770b
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468943
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
This patch makes multi SGL case possible to call spdk_nvmf_request_get_buffers()
per WR.
This patch has an unrelated fix to clear req->iovcnt in
reset_nvmf_rdma_request() in UT. We can do the fix in a separate patch
but include it in this patch because it is very small.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If6e5af0505fb199c95ef5d0522b579242a7cef29
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468942
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Update transaction length wrt to medata size
Change buffers handling in the case of enabled DIF - add function nvmf_rdma_fill_buffer_with_md_interleave to split SGL into several parts with metadata blocks between them in order to perform RDMA operation with appropriate offsets
Add DIF generation before executing bdev IO operation
Add parsing of DifInsertOrStrip config parameter.
Since there is a limitation on the number of entries in SG list (16), the current approach has a limitation on the max transaction size which depends on the data block size. E.g. if data block size is 512 bytes then the maximum transaction size will be 512 * 16 = 8192 bytes.
In adiition, the size of IO buffer (IOUnitSize conf param) must be aligned to metadata size for better perfromance since metadata is treated as part of this buffer. E.g. if the initiator uses transaction size = 4096, data block size on nvme disk is 512 then IO buffer size should be aligned to (512 + 8) which is 4160. In other case an extra IO buffer will be consumed which will increase the number of entries in SGL and in iov.
Change-Id: I7ad2270fe9dcceb114ece34675eac44e5783a0d5
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Sasha Kotchubievsky <sashakot@mellanox.com>
Signed-off-by: Evgenii Kochetov <evgeniik@mellanox.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465248
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Test all 3 IOV positions but only on src bufs as the dst buf
code under test is identifal and the amount of test code is
rather large.
Change-Id: Idbb635149a5737df9d508adc9dba69e84ec024d3
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466157
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
To make next patch in this series clearer
Change-Id: I6654a92309b4b98351e3793439ecff1b10a24863
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467287
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
By moving the success test case to the end we avoid the scan-build
issue however the last test case was already testing success so just
udpated the comment and free the memory at the end.
Fixes issue #933
Change-Id: I0ca81f240d3af32c414b0c886fda5b14ba37e490
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467302
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
spdk_pci_device_claim() could create a file on the
filesystem that couldn't be deleted programatically.
It could only be overwritten - e.g. by another spdk
instance - but this didn't really work if that
another instance had less privileges and hence no
access to the previous file.
This is exactly the case we're seeing on our CI when
running SPDK as non-root. In general it's a good idea
not to leave any leftover files, so now we'll delete
the pci claim file when the spdk process exits.
spdk_pci_device_claim() used to return a file descriptor
that could be simply closed to "un-claim" the device.
It'll now return only a return code. The fd will be
stored inside spdk_pci_device and will be closed either
when user calls the newly introduced spdk_pci_device_unclaim(),
or when the device is detached.
We'll still need to clean up those files somewhere in
our test scripts (probably ./setup.sh cleanup) to
clean up after crashed processes or so - but we don't
necessarily want to run such scripts inside the autotest
whenever a non-root spdk is about to be started.
Change-Id: I797e079417bb56491013cc5b92f0f0d14f451d18
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467107
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Purpose: Prepare for the further optimization work
to use one bigger buffer to read more data for
reducing system calls.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Ie92603b09308bd3149263269fdec355b67251b37
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468538
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
These aren't used anymore.
Change-Id: I91400f1ad8a620d84f1b7478ffa551bb1755d233
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468505
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
These were removed from the nvmf target, so the stubs aren't
needed.
Change-Id: I77b783019ee842c15d92b89cdffcb342b10d92c6
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468504
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
The calls were removed from the code, so we don't need
the stubs anymore.
Change-Id: Ie3616d186ab172c3b7a6223b4ff754308fad9dc0
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468503
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
It is a very rare thing for a buffer to be split over two memory
regions. In fact, it is only possible in dpdk versions where
--match-allocations is not passed as a startup parameter to dpdk but
dynamic memory allocation is enabled.
By adding a small helper function, we avoid failing an I/O because it
was assigned one of these improperly aligned buffers. Also, we try to
remove the buffer from circulation so that it doesn't get picked up
again by another request.
Also, add a unit test to catch this case.
Change-Id: Ia09865c2f77160a960571665b29c4533b11758ae
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467446
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
In prep for replacing some of the internal r/w calls with function
pointers based on RAID level, just call spdk_bdev_io_get_buf()
directly in the submit path for reads. This:
* will reduce the number of places where unique calls to the
upcoming function pointer will be
* bring it in line with how the majority of other bdev modules look
* actually increase UT coverage by about 10% as we're now calling
spdk_bdev_io_get_buf() and it's callback.
Change-Id: I7e6da0dab80687988ba52f57b0d9e2dbf20676dc
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467538
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The dependencies between vhost and rte_vhost were not added during
earlier changes. This change moves the rte_vhost directory up to the
level of the other libraries and adds the proper dependencies for when
it is linked.
Change-Id: I089de1cd945062b64975a0011887700c0e38bb0f
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467700
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Removing queuing tests as they are really only testing mocked functions,
minimal coverage is gained here and the queueing logic from a UT
perspective is part of bdev, not a bdev module.
This is a prelude to adding RAID 1E which will start with abstracting the
RAID r/w functions and it may not look like it now, but getting rid of
this UT code will make the move to function pointers for r/w based on
RAID level a bit smoother.
Change-Id: I01eef2aa99b2bdd4308ddef9bad9dd1121ef7470
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/467537
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For in each loop, encoding with Arm NEON deals with 48 bytes and decoding
deals with 64 bytes:
encode: add test with src_len=48 and more than 48;
decode: add test with src_len=64 and more than 64.
Signed-off-by: Richael Zhuang <richael.zhuang@arm.com>
Change-Id: Ie156d147165a2511eed03d212eb78300e0edc84c
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465734
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Remove them all at once. spdk_ prefix should be
only applied to publicly exported functions.
Change-Id: Ib6d2bd0954ec5cb7c8cf253d79b9d3cd8aa0eeef
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466728
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Vitaliy Mysak <vitaliy.mysak@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This unifies buffer management among transports further and is a
preparation to make buffer allocation asynchronous.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I8c588eeac4081f50fe32605feb7352f72c628d95
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466847
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Both RDMA and TCP transport have uesd group for such case. Hence
FC transport changes to use group instead of tp_poll_group.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ic4b401179da506bb204c3ec48650db87f91fe72a
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466843
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The pointer to nvmf_poll_group is set in nvmf_transport_poll_group_create()
after returning nvmf_fc_poll_group_create(). Hence holding it into
struct spdk_nvmf_fc_poll_group is duplicated and can be removed.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I7087c5cdb94b0b0c5f51b0b63b631c08266c90d0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466842
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
RDMA transport have used rgroup and TCP transport have used tgroup
for such case. Hence FC transport changes to use fgroup instead of
fc_poll_group.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I91b7ad6a1c6e45caf92801b0635b18d48b3c9810
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466841
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Keeping a global discovery log page was meant to be a time saving
mechanism, but in the current implementation, it doesn't work properly,
and can cause undesirable behavior and potential crashes. There are two
main problems with keeping a global log page.
1. Admin qpairs can be assigned to any SPDK thread. This means that when
multiple initiators connect to the host and request the discovery log,
they can both be running through the spdk_nvmf_ctrlr_get_log_page
function at the same time. In the event that the discovery generation
counter is incremented while these accesses are occurring, it can cause
one or both of the threads to update the log at the same time. This
results in both logs trying to free the old log page (double free) and
set their log as the new one (possible memory leak).
2. The second problem is that each host is supposed to get a unique
discovery log based on the subsystems to which they have access.
Currently the code relies on whether the discovery log page offset in
the request is equal to 0 to determine if it should load a new discovery
log page or use the cached one. This is inherently faulty because it
relies on initiator provided value to determine what information to
provide from the log page. An initiator could easily send a discovery
request with an offset greater than 0 on purpose to procure most of a
log page provided to another host.
Overall, I think it's safest to not cache the log page at all anymore
and rely on a thread local fresh log page each time.
Reported-by: Curt Bruns <curt.e.bruns@intel.com>
Change-Id: Ib048e26f139927d888fed7019e0deec346359582
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466839
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is a small performance optimization and an effort to unify
I/O buffer management further among transports.
It is ensured that the request is the first of STAILQ when
spdk_nvmf_tcp_send_c2h_data() is called or the case
TCP_REQUEST_STATE_NEED_BUFFER is executed in spdk_nvmf_tcp_req_process().
Hence change TAILQ_REMOVE to STAILQ_REMOVE_HEAD for these two cases.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I0b195874ac22a8d5ecfb283a9865d2615b7d5912
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466637
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Not any different from the test_env version in this patch but it will
be in the upcomiong series as the 2MB tests are added as we will need
to manipulate the size param.
Change-Id: I13a7544546b5296421fe5b696c8777e402bacc35
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466076
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Most of the assignments followed the DIRS-($(CONFIG_X)) pattern, but
there were a couple of assignments using a different pattern.
Change-Id: I7c80fec2813c32cb7676912d72805565f77b2e3d
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466469
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Use spdk_nvmf_request_get_buffers() and spdk_nvmf_request_free_buffers(),
and then remove spdk_nvmf_tcp_request_free_buffers() and
spdk_nvmf_tcp_request_get_buffers().
Set tcp_req->data_from_pool to false after spdk_nvmf_request_free_buffers().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I286b48149530c93784a4865b7215b5a33a4dd3c3
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465876
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Use spdk_nvmf_request_get_buffers() and spdk_nvmf_request_free_buffers(),
and then remove spdk_nvmf_rdma_request_free_buffers() and
nvmf_rdma_request_get_buffers().
Set rdma_req->data_from_pool to false after
spdk_nvmf_request_free_buffers().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ie1fc4c261c3197c8299761655bf3138eebcea3bc
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465875
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is a prepration to unify buffer management among transports.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6b1c208207ae3679619239db4e6e9a77b33291d0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466002
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is a preparation to unify buffer management among transports.
struct spdk_nvmf_request already has SPDK_NVMF_MAX_SGL_ENTRIES (16) * 2
iovecs. Hence incresing the number of buffers twice will be no problem.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Idb525abbf35dc9f4b8547b785b5dfa77d106d8c9
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465873
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Purpose: Prepare the further optimnization in the
target side whening receving pdu headers, we expect
to use zero copy.
Change-Id: Iae7f9106844736d7160d39d0af1f5941084422ec
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465380
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Some time ago spdk_subsystem_init() used spdk_events as
callbacks, but it was removed.
This patch removes left over UT stubs.
Change-Id: Id25ac8e4e338c172d21161dede6dc046f0860279
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464682
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This change adds return code to spdk_subsystem_init().
Making it's caller responsible for handling application
state - such as calling spdk_app_stop().
This change implies that start_subsystem_init RPC does not
stop the application on failure, only reports back the error.
Renamed g_app_start/stop variables to now more relevant
g_subsystem_start/stop.
Change-Id: I66a7da6ecfb234a569c65279cc4b210ddac53d2a
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/464412
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Track the band under defrag inside the reloc module. This allows for
multiple bands being defragged at the same time (e.g. extra one due to
write fault) as well as makes it easier to handle cases when relocating
a band that has no valid blocks.
Change-Id: Ia54916571040f5f4dfdb8f7cdb47f28435a466d8
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465937
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch adds new interface for opening bdev and
implements new style remove event. With that changes
user can be notified about different types of events
that occur in regards to bdev. spdk_bdev_open_ext
function uses bdev name as an argument instead of bdev
structure to remove race condition where user gets
the bdev structure and bdev is removed after getting
that structure and before open function is called.
spdk_bdev_open is now deprecated.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I44ebeb988bc6a2f441fc6a0c38a30668aad999ad
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455647
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Currently we *always* wait 2 seconds before starting
controller initialization during attach. This
works around an issue where some older Intel NVMe SSDs
could not handle MMIO writes too soon after a PCIe
FLR (which would be triggered when VFIO was enabled).
After further discussion with Intel experts, we know
the SSD models that exhibit this issue. So we can
quirk this so that only the older SSDs incur the extra
delay.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ieb408c24f6afd5bd5147d1c87239aa20f2d13511
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466064
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Scan-build on Fedora29/30 reports error, which this patch fixes:
bdev_ut.c:1436:17: warning: The left operand of '!=' is a garbage value
CU_ASSERT(desc != NULL);
~~~~ ^
/usr/include/CUnit/CUnit.h:123:30: note: expanded from macro 'CU_ASSERT'
{ CU_assertImplementation((value), LINE, #value, FILE, "", CU_FALSE); }
^~~~~
bdev_ut.c:1654:17: warning: The left operand of '!=' is a garbage value
CU_ASSERT(desc != NULL);
~~~~ ^
/usr/include/CUnit/CUnit.h:123:30: note: expanded from macro 'CU_ASSERT'
{ CU_assertImplementation((value), LINE, #value, FILE, "", CU_FALSE); }
Fixes#924
Change-Id: Ia7dc6ce066ac80fc45f022eefd43a224d2f11503
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466110
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
In prep for testing the 2MB boundary condition multiple changes
were needed:
* update mocked mbuf function for chaining
* init next pointer to NULL during mbuf allocation
* set and check expected physcal addresses in _compress_operation()
* init iovec values in test routines to more sane values
Change-Id: Icff030e8bef693952f7da66e7aae77e207fbfd40
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465983
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Present since the refactoring on driver init function.
Change-Id: I5b2877f4278b62a9efa53395f6910ef199f2c100
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465981
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Will be needed to add specific tests for crossing a 2 MB boundary
later in this series.
Change-Id: I7404a019ff2f837f54ffdef39c6219e86aa258f1
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465968
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Remove code that was freeing memory in the code under test. It was
no longer needed following a refactor of the init code and was
causing a double free.
Change-Id: I99018587ac12e01d4fe950e0718c23790ce7ce41
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465966
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is a part of a change that will introduce
new spdk_bdev_open_ext function. This will make
possible to pass callback function while opening
bdev which will be called when some bdev events
occur.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I3e552edd5c90dacd39885e75e9114e48dddf50ea
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/463157
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
To avoid changing the actual compress/decompress routines, just
use a scratch buffer to support incoming iovecs.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I55851866dd1b2d9c0eb44fac35d050d7abd00e4e
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465355
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
First in a series to fix broken reduce unit tests, they have not
been running in CI for quite some time. Once they are working
again, will have Jenkins udpated to make sure they are run per
patch.
Change-Id: I12767dfea61a2e9a1ced85b9b247b5aeadc1edde
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465207
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This will provide a unique identifier which can be used to provide get
and set methods within the RPCs.
Change-Id: Idd144e99e49b8d26530f60530d2e908b18fa251b
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465330
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
