This API is a helper for getting the full discovery
log page from a discovery controller. It will read the
log page header to get the total number of entries,
allocate a buffer for all of the entries, and then
issue a series of get_log_page commands to read each
4KiB worth of entries.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I02666ef5adcb9fc8825a221655811ace708f97b8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10564
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The NVMe bdev module will support two features, delayed reconnect and
delete after multiple failures of reconnect to improve error recovery.
The recently added two APIs, spdk_nvme_ctrlr_reset_async() and
spdk_nvme_ctrlr_reset_poll_async(), were not good enough.
spdk_nvme_ctrlr_reset_ctx was not necessary. It had only a pointer to ctrlr.
Using a pointer to ctrlr directly saves us from undesirable malloc error
processing.
Separate spdk_nvme_ctrlr_reset_async() into spdk_nvme_ctrlr_disconnect()
and spdk_nvme_ctrlr_reconnect_async(). spdk_nvme_ctrlr_disconnect()
disconnects ctrlr including disconnecting adminq.
spdk_nvme_ctrlr_reconnect_async() moves the ctrlr state to INIT.
Then rename spdk_nvme_ctrlr_reset_poll_async() by
spdk_nvme_ctrlr_reconnect_poll_async().
Finally deprecate spdk_nvme_ctrlr_reset_async() and
spdk_nvme_ctrlr_reset_poll_async().
The following patches will change the NVMe bdev module to use these new APIs.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Id1d6858dcdc5fc2e9db0a6ebf3f79cab4f9bbcb7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10091
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
async_mode option is currently supported in PCIe transport layer
to create io qpair asynchronously. User polls the io_qpair for
completions, after create cq and sq completes in order, pqpair
is set to READY state. I/O submitted before the qpair is ready
is queued internally. Currently other transports only support
synchronous io qpair creation.
Signed-off-by: Monica Kenguva <monica.kenguva@intel.com>
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ib2f9043872bd5602274e2508cf1fe9ff4211cabb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8911
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Nvmf/vfio-user uses this API to map NVMe command sent from
VM from Guest Physical Address to Host Virtual Address, so
now we moved this API from the nvme library to nvmf/vfio-user
as an internal API.
UT code will be added back in coming patch.
Change-Id: I54817fc9811ccd9ddd97b3aa6762a2fce4bbdda6
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8574
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
The hotplug lib can be used for pcie devices
such as nvme, virtio_blk and virtio scsi.
For the sigbus handler, there is only one in a
process and it should handle all the devices.
And align nvme to the hotplug lib
Add the ADD uevent support for allowing the
device hotplug.
Change-Id: I82cd3b4af38ca24cee8b041a215a85c4a69e60f7
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5653
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This patch is used to add spdk_nvme_poll_group_get_optimal
public API.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Iee34c89e0e1ff1f81167b18e198c144ca28f71de
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3311
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
When NVMf target linked with vfio-user library, we can use
vfio-user client library to connect to the target.
Here is the three examples that can work with target:
identify -r 'trtype:VFIOUSER traddr:/var/run/muser/domain/muser0/8' -g
perf -r 'trtype:VFIOUSER traddr:/var/run/muser/domain/muser0/8' -g -q 1 -o 4096 -w read -t 10
reconnect -r 'trtype:VFIOUSER traddr:/var/run/muser/domain/muser0/8' -g -q 32 -o 4096 -w randrw \
-M 50 -t 10 -c 0xE
You can run the following test script test/nvmf/target/nvmf_vfio_user.sh to have a quick test,
currently enabled with NVMe Identify,Perf,Reconnect tools.
Change-Id: Ieb9842b2f372184fffbf7f23e4aad26feb47c350
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3839
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
There are some common data structures and APIs in pcie transport
which can be used both for pcie and vfio-user transport, so move
the common code into a new header and source file.
No actual logic change just the code movement except remove the
static function declarations.
Change-Id: Ie9021e703a5780fdd6840f0e3cfea76a0017a811
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5923
Community-CI: Broadcom CI
Reviewed-by: sunshihao <sunshihao@huawei.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The zone append command, which is part of the Zoned Namespace Command Set,
has a maximum data transfer size that can be less than or equal to mdts.
Since zone append commands will not be allowed to be split, the user has
to be able to get the maximum zone append data transfer size. Add a
function that returns this limit.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I9da2672ea8a307ff62251c069a42f7540765e08b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5140
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add getters to the ZNS specific data structures, so that an
SPDK application, e.g. examples/nvme/identify/identify.c,
has the ability to get and utilize the information in them.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I26056161093cc811acb6840ff7e2068e5f6058f6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4412
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
LOCAL_SYS_LIBS is meant to define *direct* system
library dependencies for a given library. libuuid
is directly used by the SPDK util library and then
other SPDK libraries use uuid indirectly through
util.
So only the util library should include uuid in
LOCAL_SYS_LIBS.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ia0d2d63f48e6f89891164cf2f9dc4c7a6476d4e3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4366
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add support for getting the Command Set Identifier for a given namespace.
The SPDK_NVME_CAP_CSS_IOCS feature can be implemented on top of an old NVMe
specification. If the feature is set, retrieve the NS ID Descriptor List
regardless of the NVMe specification version. The quirk is still respected.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I7b257115ecb0d813ba75201c0f48960c7070dcc9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4085
Community-CI: Broadcom CI
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
These dependencies were removed in patches that added
RDMA provider. It was incorrect change since it causes
SEGFAULT when SPDK is built with shared libraries
Change-Id: I15f4ff86a75b3d080e1c7c89d75af4959c4ed989
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2900
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Seth Howell <seth.howell@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This is an important aspect of ABI versioning.
There was a change to the spdk_bdev_opts struct
which is accessible from the public API that results
in an ABI change.
There was also a change in the spdk_accel_module_if struct that
will affect new modules so its major version needs to be revved.
There was also a change in the publically accessible rmda_hooks
structure which forced an ABI change in the NVMe library.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I5cc6886fe01b4adc2836b6e15995471f0361dc29
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2663
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Also, while we are here, consolidate setting SO_SUFFIX to one spot.
Previously, it was possible for a library to slip through
without an SO version.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I4db5fa5839502d266c6259892e5719b05134518c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2361
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This patch adds use of RDMA provider API to NVMEoF initiator.
Makefiles have been updated with new RDMA lib dependency
Change-Id: Ieaefeb12ee9681d3db2b618c5cf0c54dc52230af
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1657
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This API will allow us to simplify the polling mechanism for qpairs on a single
thread. It also will pave the way for doing transport specific aggregation of
qpair polling to increase performance.
The generic implementation is included. The transport specific calls
have yet to be implemented.
Change-Id: If07b4170b2be61e4690847c993ec3bde9560b0f0
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/579
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
the nvme, nvmf, and thread libraries have all had public APIs
removed or changed since the API was changed to 2.0 and
backported to 20.01.1 we should rev these so versions to make
that distinction obvious.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Id48454b8d0451794abad4db452b5c4e337b23c0b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1269
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This will allow us to keep track of compatibility issues on a
per-library basis.
Change-Id: Ib0c796adb1efe1570212a503ed660bef6f142b6e
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1067
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
NVMe character device implementation. This patch adds implementation
of IO producer using CUSE library. It allows to create nvme device
nodes in linux kernel for controller as well as for namespace and
process ioctl requests as usual from linux environment.
Both devices (controller and namespaces) are exposed as character
devices.
To compile NVMe CUSE module use "./configure --with-nvme-cuse".
Names for created CUSE devices can be retrieved using
spdk_nvme_cuse_get_ctrlr_name() and spdk_nvme_cuse_get_ns_name().
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I0fc9a9a1ef3c9c2b3112d07c2b4b1f8d49665ee1
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466917
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This patch allows to send IO requests from external module to the nvme
device.
External module should call nvme_io_msg_ctrlr_start() to start IO message
producer on the controller and enable sending messages.
nvme_io_msg_send() is used to send IO to NVMe driver thread context,
where passed function will be called. Allowing the external module to
issue IO as needed.
NVMe driver users should poll spdk_nvme_io_msg_process() to move forward,
sending IO from external module and process their completions.
Change-Id: Ie59abac69870c4e4daa50120c747f3b620395921
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/471386
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
First submission. Implemented part of the Opal library
and "scan" function. Can be invoked by nvme_manage.
Change-Id: Iba86d86dd3af06a06b6805120ee5005af8183459
Signed-off-by: Chunyang Hui <chunyang.hui@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/439335
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
It is the first patch to follow the NVMe over fabrics
spec and implmenent the NVMe/TCP transport. It can be
divided into work in the host and target sides:
Host side: Add the TCP/IP transport in nvme lib (lib/nvme).
Target side: Add the TCP/IP transport in nvmf lib (lib/nvmf).
Change-Id: Idc4f93750df676354f6c2ea8ecdb234e3638fd44
Signed-off-by: Ziye Yang <optimistyzy@gmail.com>
Reviewed-on: https://review.gerrithub.io/425191
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Chandler-Test-Pool: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This prevents the SPDK build from requirng unnecessary dependencies when
not compiling certain features. Also, fixes github issue #434
Change-Id: I7d0520474f3656ae32670313f2290e6b741c5ca8
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/426131
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Chandler-Test-Pool: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Lance Hartmann <lance.hartmann@oracle.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
These functions are generic and may be used for other NVMe-oF
transports.
Change-Id: Idb3aa30d9b0b1be7b60b85ab4911b28db35977a4
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/416575
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch adds support for following Open-Channel vector commands:
* Vector Chunk Reset
* Vector Chunk Write
* Vector Chunk Read
* Vector Chunk Copy
Implementation is consistent with Open-Channel specification (rev. 2.0)
This patch provides unit tests for new public NVMe
Open-Channel namespace commands.
Change-Id: Ic71be9357c61c5de82ca672e82a71aa933bd1875
Signed-off-by: Jakub Radtke <jakub.radtke@intel.com>
Reviewed-on: https://review.gerrithub.io/414969
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Young Tack Jin <youngtack.jin@circuitblvd.com>
This patch adds to nvme driver new public API dedicated for
Open-Channel:
* spdk_nvme_ocssd_ctrlr_cmd_geometry
Change-Id: I69592618d9bcc280346258e771195683d5b33893
Signed-off-by: Jakub Radtke <jakub.radtke@intel.com>
Reviewed-on: https://review.gerrithub.io/412816
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Only Makefiles for libraries that directly depend on DPDK (rather than
the SPDK env abstraction) should add $(ENV_CFLAGS).
Change-Id: Ifdf44d3ef8c42bbf7f20edd524b330d00658235b
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-on: https://review.gerrithub.io/392818
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Function pointers will not work for the DPDK multi-process model (they
can have different addresses in different processes), so define a
transport enum and dispatch functions that switch on the transport type
instead.
Change-Id: Ic16866786eba5e523ce533e56e7a5c92672eb2a5
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Make the quirks mechanism generic in preparation for quirks for devices
from other vendors.
Change-Id: Ic003b020a38f1b966021db30e3f2bce9cf6a1a0d
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
This will allow factoring out PCIe-specific code into a swappable
transport so that NVMe over Fabrics host support can be added.
Change-Id: I4df74dd268d655e3b36e8d6114ebe7d79a24844d
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
This allows users to swap out SPDK's third party
libraries for an implementation based on their own
framework.
Change-Id: Ia0b7384ce5e31acba5ad0d7002dec9e95b759c52
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Explicitly include spdk.common.mk at the top of all lib Makefiles so
that CONFIG options and other predefined variables are set.
Change-Id: I1e560c294fe8242602e45191a280f4295533ae44
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Resolve relative paths before using them to clean up command lines.
This should also help shorten the overall command line length that gets
embedded in the binary and used when locating the executable from a
coredump.
Change-Id: Ibff9849ede198bb04313496c8b7131485ffaf14f
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
This patch adds Intel NVMe device list and overrides the
supported log pages according to the quirk list.
In particular, the READ_CMD_LATENCY and WRITE_CMD_LATENCY pages are
supported on Intel DC P3x00 devices despite not being listed in the
Intel vendor-specific log page directory.
Change-Id: I3a2b6a5fa142c6e9c93567df65e85980bd3c7cc0
Signed-off-by: Cunyin Chang <cunyin.chang@intel.com>
Also add a space between Copyright and (c).
The copyright year can be determined using git metadata.
Also remove the duplicated "All rights reserved." - every instance of
this line already has a corresponding "All rights reserved" immediately
below it, except for examples/ioat/kperf/kmod/dma_perf.c, where I have
added it manually.
Performed using this command:
git ls-files | xargs sed -i -e 's/Copyright(c) \(.*\) Intel Corporation. All rights reserved./Copyright (c) Intel Corporation./'
Change-Id: I3779f404966800709024eb1eb66a50068af2716c
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Use $(CLEAN_C) throughout the Makefiles to clean up a consistent set of
generated files.
This also adds coverage files to the list of cleaned files.
Change-Id: Iceb922935a45c9eecbf2f3443bd0ee4f5c966825
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
lib/memory was already using this pattern; extend it to lib/util and
lib/nvme.
Change-Id: I84a633d7805522fc94d8fc11ad5486ce552702e5
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
The .o files are always kept anyway, so there is no need for an explicit
rule.
Change-Id: Id1687ba89daabfda5802e4328deb127403277928
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Add common $(COMPILE_C), $(LINK_C), and $(LIB_C) variables that contain
the commands to build a .o from a .c, an app from objects and libraries,
and a library from objects, respectively.
Change-Id: Ie2eaa13156b8bf3db7a4ffa66161382d829aef07
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Set SPDK_ROOT_DIR explicitly in each Makefile so that make from a
subdirectory will work (assuming all dependencies from the upper
directory have already been built). This allows partial rebuilds of the
source tree, as well as building the unit tests without requiring DPDK.
Change-Id: I3f65b805d490b40ff5ec53cceb61df542ce814f1
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Move dependency includes into a new spdk.deps.mk file,
then include it at the end of Makefiles that build
source files.
Also add a test to autobuild.sh to confirm that
binaries are regenerated if we make after touching a
header file.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: If6a1905706a840f92cbdf3ace7fbdb27fe2de213
