This keeps track if an nvme_ctrlr was created
implicitly by the discovery service.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I493b7cacfe563737f45a1fffca98855a1929a751
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11817
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
These parameters will be used for any controller created
by the discovery service.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I221b791f38b9c5797ba084c647a98b82c102a121
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11942
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Some targets report they support log page offset,
but then fail GET_LOG_PAGE commands that specify
a non-zero offset, or report the wrong number
of discovery entries when reading more than the
discovery log page header but not the entire log
page.
So just revert to reading the entire discovery log
page, after we've read the header to know how big the
log page will be. This means that when we read the
log page initially (without the individual entries),
we need to save off the genctr, since it will get
overwritten when we read the log page again. We can
just store this in the discovery context, and compare
it to the genctr that we read with the whole log page.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I34929253312fed9924db58904a051f3979283730
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11478
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Attempt to start a connection once per second, but
after a connection is successfully started, change
the timer period to one millisecond instead.
This ensures lower response time to AER events when
the discovery controller is operational, but then
decreasing rate of unsuccessful connect attempts (and
associated log messages) if/when a discovery controller
fails.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ie24036303f5b00f4a42b6575656f401ea4d578f2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11774
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Also cycle through the discovery paths if the initial
connect_async() operation fails.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I50f36949d9bba0e3bff81505712076f1a1a7aad5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11773
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
If a discovery controller fails at some point, we
will want to detach it. This can happen separately
from detaching the controller because we are stopping
the discovery service. So break out the ctrlr
detach operation into a separate phase of the
discovery_poller.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ia601b767d32bda1c8899d3a95029781c0aeee136
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11772
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
The driver always creates a single group containing all of the engines
and a single work queue.
Change-Id: I83f170f966abbd141304c49bd75ffe4608f5ad03
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11533
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
It is not used for anything.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I1d967b2d0e404756f7ceda98ddc4ee9017ec83f7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11489
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
It turns out that this can stay on the stack.
Change-Id: I961366307dae5ec7413a86271cd1dfb370b8f9f3
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11488
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
initialization
We can make the structs do all of the offset math for us.
Change-Id: Ibe6d86c2abc58655c1354f1eb31091c95cfb283c
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11487
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
These aren't ever accessed in the main I/O path, so we can read them in
whenever we need them and make the code a lot simpler.
Change-Id: Icfdbfe9f2d9db13f4d0d28b2b4103cd0c443bcf4
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11485
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Assume any given WQ we are allocated can submit the full device allowed
queue depth.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I044e1f70031ea83ae722ed285b84c06b3e5efb27
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11486
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This is no longer needed.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I08c788ca0451e739804b568d613c1e52e071c61f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11794
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
In vfio-user transport, whenever one IO is completed, it will trigger
an interrupt to guest machine. This cost quite some overhead. This patch
adds an adaptive irq feature to reduce interrupt overhead and boost
performance.
Signed-off-by: Rui Chang <rui.chang@arm.com>
Change-Id: I585be072231a934fa2e4fdf2439405de95151381
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11840
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
responder_resources parameter of rdma cm tells remote
side how many outstaing RDMA_READ of atomic operations
local side can handle.
Previously it was adjusted on queue depth but that was
not correct since these parameters do not depend on
each other. Even with qdepth=1 remote side may send
several RDMA_READ operations per 1 IO request.
With this change we report responder_resources
equal to the maximum supported by RDMA device.
Linux kernel nvme rdma driver reports this value
in the same way.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I77e5c2ead6269da44c32a75a9188429f50d32ae4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11698
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
It's already done in ioat_destroy_cb(). Proper fix required moving
the rest of the cleanup code in accel_engine_ioat_exit() to a new
device unregister callback.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Iaaa595cf5b51f7a4842315fc06270b0857ebf0c5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11930
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Fill is sent in as a uint8, we need to populate the full uint64
input with the uint8 pattern or we'll get a miscompare. This is
how idxd was doing it, instead of adding the same code to ioat just
move it up a layer.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ia4aab1c6230f35ab88bb8a0e3b8e16dbd93007c7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11947
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Functions _start_writev_request and _write_decompress_done
have very similar decomp_iov configuration code, the only
difference is whether to fill gaps with zeroes or with
decompressed data. Move this code to a common function,
that will reduce amount of changes in the next patch
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I14509a17a12156b25ceab85a98b4dbd6fb11c732
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11969
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Some compress drivers may not support SGL for in or
out buffers. Extend spdk_reduce_backing_dev with two
flags that will be used by reduce library to correctly
build iovs
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: Icee9383364124888c2109894c959c06710d91250
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11968
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add NVME_CTRLR_ERRLOGs to nvme_ctrlr_process_init().
The main goal is to help with debugging #2201 issue.
Change-Id: I1ae6a9b30d6124dfe25eb7912402c37d476b0d4c
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10627
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Rename ->doorbells to ->bar0_doorbells. This will help avoid confusion
later with shadow doorbells.
Signed-off-by: John Levon <john.levon@nutanix.com>
Change-Id: Id432938cfeb3033e79dc6e1b491dad964227687a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11788
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Thanos Makatos <thanos.makatos@nutanix.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
NVMe over PCIe Transport Spec 3.1.2:
The host should not read the doorbell registers.
Explicitly refuse these reads.
Co-authored-by: John Levon <john.levon@nutanix.com>
Signed-off-by: John Levon <john.levon@nutanix.com>
Change-Id: Ie64fd5ce7988ee86c612b3ef6046a57af467e266
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11787
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Thanos Makatos <thanos.makatos@nutanix.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Refactor controller reset a little bit for cleaner code.
Co-authored-by: John Levon <john.levon@nutanix.com>
Signed-off-by: John Levon <john.levon@nutanix.com>
Change-Id: I2b3323005d4e788ffe980d41c349702828886981
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11786
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
If we're in interrupt mode and live migrating a guest, there is a window
where the I/O queues haven't been set up but the device is in running
state, during which the guest might write to a doorbell. This doorbell
write will go unnoticed. This patch ensures that we re-check the
doorbells after an I/O queue has been set up.
Fixes#2410
Signed-off-by: Thanos Makatos <thanos.makatos@nutanix.com>
Signed-off-by: John Levon <john.levon@nutanix.com>
Change-Id: I161d2a0e7ab3065022b2bccbe17f019640cceeba
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11809
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
FIO config can have "env_context" field now. It allows passing to DPDK
the start-up options essential for mlx5 crypto/reduce support. This
enables using FIO plugin for testing mlx5 crypto/compress vbdev PMDs.
For example:
env_context=--allow=0000:01:00.0,class=crypto,wcs_file=/path/credentials.txt
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: I8b862a431fa5b838e337a64e736d4f6700f83599
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11633
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
- More user-friendly style of error and debug messages.
- Remove "ERROR" word from SPDK_ERRLOG() to avoid duplicating
in the log.
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: Iaee068f96e66f567fc23b34ae0ae6221c1bd710c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11632
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
- Fixed duplication of key, key2, drv_name, cipher, etc., fields in
struct bdev_names and struct vbdev_crypto. Moved all of them into
the new struct vbdev_crypto_opts, which is re-used by both structs.
This aslo removes duplication in error handling and fininalization
logic that checks the keys are zeroed out and properly freed.
- Moved unhexlify into vbdev rpc code. All keys passed to vbdev
already in the binary form.
- Provide meaningful error messages in the rpc response on keys
validation issues during setup of crypto vbdev.
- Updated unit tests.
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: I1fab8771bbbc0cd2f359f0d105fec28fb86893b3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11631
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
- Added hexlify() and unhexlify() for key and key2. This is required
for keys that contain zero and non-ascii characters. Since binary
keys may contain zero character, strlen(key) cannot be used and
key_size and key2_size are used instead. Non-asci chars are not
allowed in json and using hexlified keys fixes this issue as well.
- Updated documentation to clearly state that hexlified keys must
be used.
- Updated test scripts.
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: I3fce7839f7eaa67d0307071eba80b4cea472d731
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11891
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Make sure cq->group is set even in interrupt mode.
Signed-off-by: John Levon <john.levon@nutanix.com>
Change-Id: I9f722917a8e3aebbd5d66648a3909f795897ec1a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11997
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Parameters submitted by bdev trace record may not be uint64_t
type (ex: bdev_io->type), which may bring outliers in trace parsing
results. The reason is that, in _spdk_trace_record() function,
va_list hold information about variable arguments, when passing
SPDK_TRACE_ARG_TYPE_INT arguments, it will call va_arg(vl, uint64_t)
to get value. However, if the submitted type is not uint64_t,
va_arg may return outlier.
To solve the problem, the parameter should be converted into
uint64_t before be delivered into trace record if it is not
uint64_t.
Signed-off-by: zhaoshushu.zss <zhaoshushu.zss@alibaba-inc.com>
Change-Id: Id710e39581f5e7b7551f3ff3a308f122f1344f1f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11691
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
pending_async_op_num is specific to vhost_user.
To prepare for virtio_blk transport abstraction,
checking for the pending operations is moved to vhost_user
specific code from vhost_blk.
Ideally the vhost_user_dev_unregister() should be the only
function that checks this field, but due to
order of calls in vhost_scsi it needs to remain there separetly.
This should not pose any issue, as vhost_scsi is still dependent
directly on vhost_user.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I53dde73766dcf8596715560f6909a4679f8da930
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11811
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
spdk_top constantly shows scheduler data error
due to missing "_relaxed" suffix in
spdk_json_decode_object() function. This happens
when SPDK scheduler is switched to "dynamic", because
it provides more data than defined in spdk_top's
scheduler_decoders structure.
Additionally delete leftover governor code.
Fixes#2433
Change-Id: I1f849f0cb48fce5312cdc3c25d7b4529b407283c
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12010
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
are not supported
That will be used to test memory domains with logical
volumes, we need to make sure that lvol correctly
reports memory domains. Also add a counter for the
number of translation_cb calls and verify that
it is not smaller than the total number of
completed IO requests
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I42f0cb14fd24c95de830146a603de64f1a8848be
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11374
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
That is done to correctly handle metadata pointer which is part
of ext_opts structure. It will also be used by the next patch to
remove memory_domain pointer if request which uses local buffers
is split
Force the user to set correct ext_opts size, update API functions
description.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I77517d70df34a998d718cc6474fb4c538a42918f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11349
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Bdev modules must not access internal bdev_io
structure, so add a new pointer in a public
section. Pointer in internal section will be
used in next patch
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: Ib631563015b3e5fa9300d22b7ae59d8db43c8275
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10421
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch is a preparation for enabling of memory domains
pull/psuh functionality. Since memory domains API is
asynchronous, this patch makes asynchronous operations
with bounce buffers.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: Ieb1f2a0c151149af58cfd7607dbde4c76c3c288d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10420
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Here were some cases for file->name using strdup
missing check for no memory, but some had.
So add them.
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: I91feeea3711f127135aedf37e53624811a4ab5e8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11989
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
With these we can write a simple bpftrace script to identify work being done,
and in particular what woke us up from sleeping.
Signed-off-by: John Levon <john.levon@nutanix.com>
Change-Id: I8997d847625ee4558092dbd753e6fc1b17beca92
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9424
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
SPDK has settled on what the optimal DSA configuration is, so let's
always use it.
Change-Id: I24b9b717709d553789285198b1aa391f4d7f0445
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11532
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
The names on these were changed.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ib75a60342c08f72dad39635a9244421c1cca5485
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11793
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
