Send the given NVM I/O command, I/O buffers, lists and all to
the NVMe controller.
This is a low level interface for submitting I/O commands directly.
This can only be used on PCIe controllers and qpairs.
This function allows a caller to submit an I/O request that is
COMPLETELY pre-defined, right down to the "physical" memory buffers.
It is intended for testing hardware, specifying exact buffer location,
alignment, and offset. It also allows for specific choice of PRP
and SGLs.
The driver sets the CID. EVERYTHING else is assumed set by the caller.
Needless to say, this is potentially extremely dangerous for both the host
(accidental/malicionus storage usage/corruption), and the device.
Thus its intent is for very specific hardware testing and environment
reproduction.
Signed-off-by: James Bergsten <jamesx.bergsten@intel.com>
Change-Id: I595fe02fe0dfa9c3ceba1ac116b6900357b02d2c
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/451994
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reset the device to its factory defaults.
Change-Id: I43f7dc8fb7bd5226283a4762beac0e2cf016f698
Signed-off-by: Chunyang Hui <chunyang.hui@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/445253
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Also make some modification for invoking process in
nvme_manage tool.
Change-Id: Ib54db43d7336d3e839e7d9317c292b9a57b38f80
Signed-off-by: Chunyang Hui <chunyang.hui@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/445059
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
When a Namespace was removed all the field will be zeroed, which
may lead to being divied by zero error when IO is running, especially
with perf tool. The perf tool doesn't add hogplug support, so
we add the additional check here to avoid such issue.
Fix issues #728 and #629.
Change-Id: I0e387c8c1bd4f3d40130377e2e0f5143f43be6a3
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/451762
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
logical_block_size and geometry_logical_block_size are uint32_t,
so correct conversion for endianness is used now.
Change-Id: Iaa5ff576da8bc4ca65fa21f28eb3afd30507b00a
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/451867
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
The mode of dmb oshld can guarantees cpu sequential execution,
which has less impact on performance.
Change-Id: If30b6a682a2216eecd1da039267ed4f5471afc38
Signed-off-by: h00448672 <heyang18@huawei.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/446827
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The upper levels of the stack allow for this, so we should follow that
pattern so I/O don't break here.
Change-Id: Ia862f14975a551b0675bafd7709fb7897d0d567e
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450685
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The while loop in this function was structured such that if the final
child request did not contain a full number of SGE elements, it would be
truncated. We need to not only check whether we have a full number of
SGEs, but also if the current child has consumed the end of the parent
request.
Change-Id: I7df6c224e9ab66033c92d2cf1af10452f5cdfd9b
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450684
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is an attempt to fix device hotremove with VFIO.
A soft device hotremove request through sysfs [1] would
currently just block until the SPDK process manually
releases that device - e.g. upon an RPC request.
VFIO won't get unbound from the device untill userspace
releases all its resources. VFIO can signal a pending
hotremove request by kicking any file descriptor provided
by the userspace - and DPDK does provide such descriptor -
but SPDK does not listen on it.
DPDK does offer handy API to listen and in this patch
we make use of it inside our env/pci layer. Within
a DPDK callback we set an internal per-device hotremove
flag, which upper-layer SPDK drivers can poll with a new
env API - spdk_pci_device_is_removed().
The VFIO hotremove event will be sent to primary
processes only, so that's where we listen.
We make use of this new API in the NVMe hotplug poller,
which will process it just like any other supported
hotremove event.
Fixes#595Fixes#690
[1] # echo 1 > /sys/bus/pci/devices/<bdf>/remove
Change-Id: I03d88271c2089c740e232056d9340e5a640d442c
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/448927
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This avoids a data dependent load to find which
callback to call in the completion path.
Change-Id: Ifa20790a7af3332a74bc45037e589668744af797
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450558
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
The same information can be obtained by checking the req
field for NULL.
Change-Id: I9689ee0be33537fd6d3f35d8c3710fabab5e1928
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450557
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
When copying the NVMe command from the request to the actual
submission queue slot, use a non-temporal move instruction.
The submission queue slots are never read by software - only
written to. So don't pollute the CPU cache with their contents.
Change-Id: I112f721abfac03bd7b33ec9ddf783d4bf2952b42
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450193
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
There are several places where we have the tracker
pointer, yet we go find the tracker again by getting
the tr->cid and using that index to find the tracker
again in the qpair's array. That's really silly.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I54acd642a2c9821f2b95e17563904b859495081a
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450308
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Current the idea is:
Convert the multiple SGL into the single SGL and send it
out.
Change-Id: I8e571704e9d7c7b583f889837eead7cac1982fcd
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/448262
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
First submission. Implemented part of the Opal library
and "scan" function. Can be invoked by nvme_manage.
Change-Id: Iba86d86dd3af06a06b6805120ee5005af8183459
Signed-off-by: Chunyang Hui <chunyang.hui@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/439335
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: yidong0635 <dongx.yi@intel.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Purpose: To support the multiple SGL later.
Change-Id: I133a451100b736353cf98a6aaca879d290ff5b67
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/448259
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This function will be exteneded later for multiple SGL
support.
Change-Id: I1f6962ec03c72e335efaa311a12d3891312fcc53
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/449968
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: wuzhouhui <wuzhouhui@kingsoft.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Fixes#722. The state was set in nvme_ctrlr_identify_id_desc_async
Signed-off-by: cranechu <cranechu@gmail.com>
Change-Id: I232f0035e8c45d49eca2de7174c91860a299d804
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/449527
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Logically we should complete any I/O in the completion queue and
abort the rest of the I/O after we delete the submission queue
and completion queue, so that we would not lost any complete I/O.
We alse should complete I/O and abort I/O before destroy I/O qpair
even though the ctrlr/device has been removed.
Change-Id: Ieb28ad7b4a3a7be553f70178b29ca870b5413191
Signed-off-by: JinYu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/449316
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Similar to recently added nvme_pcie_qpair_ring_sq_doorbell.
Prepares for using this code for coalescing cq doorbell
writes in the future.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I565e103acf73b3d305e72a4440e1cc678c95faa0
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/448871
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
120 seconds is too long for controllers which can't be
setup during initialization, because this value is only
used for Admin commands so also rename as it is.
Change-Id: I0a3d3192252c0f6fc0bef4d8b868eaef2ae40fe3
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/448601
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The identify data is only valid if spdk_nvme_connect()
was used with Discovery Controller, so move this code
into the section where it belongs to.
Change-Id: I1897f38277eafc192552a09556a568e9152bb72d
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/448500
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The phys_addr param in spdk_*malloc() is about to be
deprecated, so use a separate spdk_vtophys() call to
retrieve physical addresses.
This patch also adds error checks against SPDK_VTOPHYS_ERROR.
The error handling paths are already there to account for
spdk_*malloc() failures themselves, so reuse them in case
of vtophys failures.
Change-Id: I377636e66b8c570d013c1bb2021f04bce4e6c0ce
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/416998
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Try to group data members that are used often into the
same cache lines. We still need to find more space in the second
cache line of spdk_nvme_pcie_qpair so that the important
parts of spdk_nvme_qpair fit.
Change-Id: Ib936cb2b1acc722de7ec313d6faa3812aacde394
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/447968
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Don't touch the shadow doorbells if it isn't necessary.
The flag could be combined into a bit mask with other
flags in a future patch.
Change-Id: I9ffd16468d29f0f0868cf849f7fece327eb6a294
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/447967
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Avoid ringing the submission queue doorbell until the
call to spdk_nvme_qpair_process_completions().
Change-Id: I7b3cd952e5ec79109eaa1c3a50f6537d7aaea51a
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/447239
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This is going to get called from two places shortly.
Change-Id: I2c67e719c91887987e6e65c5c0c384bed0431409
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/448311
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Users may want to connect specified controller at running time,
so this API will connect to the controller and return probe context
to users, users must call spdk_nvme_probe_poll_async() to initialize
the controller to the READY state before using it.
Change-Id: I232886b000454ee826ea73c4e1043d0d18ee0ec6
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/445657
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The purpose is to use the single readv to read both
the payload the digest(if there is a possible one).
And this patch will be prepared to support the
multiple SGL in NVMe tcp transport later.
Change-Id: Ia30a5e0080b041a65461d2be13db4e0592a70305
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/447670
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For API spdk_nvme_connect(), users can only use NULL or
struct spdk_nvme_ctrlr_opts for their own driver options,
so parameter opts_size doesn't take effect here. Since
some applications outside SPDK's git repository are using
such API, so we only remove the internal data structure
for now.
Change-Id: Ia727d2950d56abba637214ad17ecfa3eeab71d38
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/445656
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Free the probe context after the controllers in the probe
context list become READY. Then users don't need to free
the context which is allocated by SPDK driver.
Change-Id: I2dcb76bacf26a401b5b559c4326764a4ddb97e83
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/446820
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Borrow the ideas from iSCSI and optimize
the nvme_tcp_build_iovecs function.
Change-Id: I19b165b5f6dc34b4bf655157170dec5c2ce3e19a
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/446836
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
New API added for upper level to get controllers'
supported flags.
Change-Id: I51e9d0e57c355fa37f092602a94f4c08deb8898c
Signed-off-by: Chunyang Hui <chunyang.hui@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/446091
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
The nsdata assignment is strangely aligned with some
variable declarations - fix it to make it more clear.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I43b1a6d5a69ca035a21f3996e8f859a45bd10b9c
Reviewed-on: https://review.gerrithub.io/c/446447
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
VMWare Workstation NVMe emulation does not seem to write the
SHST_COMPLETE bit within 10 seconds, resulting in an ERRLOG
during detach/shutdown. So add a quirk to cover these VMWare
SSDs. But rather than squashing the ERRLOG completely for
these SSDs, just add a message instead indicating this is
somewhat expected on these VMWare emulated SSDs.
Fixes issue #676.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I3dfcb631feda639926fd712f1f41abb66cbf2096
Reviewed-on: https://review.gerrithub.io/c/445942
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Users should not access the internal probe context fields when
using the asynchronous probe API, so change spdk_nvme_probe_async()
to let it can only return the probe context pointer.
Change-Id: I0413c2d8db6cbe4539ad80919ed34dd621a9df70
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/445870
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Move req->submit_tick assignments from specific transports to generic
qpair code.
Check whether submit_tick has been assigned before doing the actual
assignment, because a request may be submitted several times and the
original submit_tick shouldn't be covered.
Change-Id: I2de8018dc21763eb5a19bb9d48dfbdef764b036e
Signed-off-by: lorneli <lorneli@163.com>
Reviewed-on: https://review.gerrithub.io/c/444702
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Seth Howell <seth.howell5141@gmail.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add a memory barrier for arm64 to prevent possible reordering
of tracker and cpl access,
because arm64 has less strict memory ordering behavior than x86.
Change-Id: I0a8716f7bfeffb0bbce27ee3174e214c8e4566b4
Signed-off-by: heyang <heyang18@huawei.com>
Reviewed-on: https://review.gerrithub.io/c/442964
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Purpose: to make the timeout work for NVMe TCP transport,
we miss this for TCP transport.
Change-Id: Iab4af988cc4796b4d6d98430453f3dbce1fcf313
Signed-off-by: Ziye Yang <optimistyzy@gmail.com>
Reviewed-on: https://review.gerrithub.io/c/445117
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Seth Howell <seth.howell5141@gmail.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch is used to implement this function.
Since we need to call nvme_tcp_req_complete in this
function, so we need to adjust the location of the
nvme_tcp_rep_complete funtion.
Change-Id: I5fc3693aec8dc166ac1eb03babcd2d73d7b00e63
Signed-off-by: Ziye Yang <optimistyzy@gmail.com>
Reviewed-on: https://review.gerrithub.io/c/444489
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Seth Howell <seth.howell5141@gmail.com>
To enable the timeout function.
Change-Id: Id5c40848957743683b6a5c2d085e7f777f14497d
Signed-off-by: Ziye Yang <optimistyzy@gmail.com>
Reviewed-on: https://review.gerrithub.io/c/444803
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
