Rename "kernel_init_connect/disconnect" methods
and create equivalents in SPDK Initiator class.
This allows to skip conditional checks in main
section of the script.
Change-Id: I23f620670d628c602dfdc1f24b2ddf493993ae12
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14739
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
Information about Target subsystems (port / nqn name /
ip address) is already saved at the time of their creation.
Avoid spawning nvme-cli processes and instead just filter
matching subsystems based on available information.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I24d16315d67e5eaade48790b7fae45664110afcb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14737
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Use tuple instead of list as this information is
supposed to be immutable later on.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: Id9806202d06368f09ede0c0d903924b101d3b86c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14736
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Permissions on /etc/systctl.conf file might be
for owner-only (root). Use sudo to make sure we
can read the file.
Change-Id: I98d77ac87f196aac82000cb42553285f22f8cdcd
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14390
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Kamil Godzwon <kamilx.godzwon@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jaroslaw Chachulski <jaroslawx.chachulski@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
per Intel policy to include file commit date using git cmd
below. The policy does not apply to non-Intel (C) notices.
git log --follow -C90% --format=%ad --date default <file> | tail -1
and then pull just the year from the result.
Intel copyrights were not added to files where Intel either had
no contribution ot the contribution lacked substance (ie license
header updates, formatting changes, etc)
Note that several files in this patch didn't end the license/(c)
block with a blank comment line so these were added as the vast
majority of files do have this last blank line. Simply there for
consistency.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I6cd3f18d1b469d5ef249d26ddb2923ca6b970bd4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/15208
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
per Intel policy to include file commit date using git cmd
below. The policy does not apply to non-Intel (C) notices.
git log --follow -C90% --format=%ad --date default <file> | tail -1
and then pull just the 4 digit year from the result.
Intel copyrights were not added to files where Intel either had
no contribution ot the contribution lacked substance (ie license
header updates, formatting changes, etc). Contribution date used
"--follow -C95%" to get the most accurate date.
Note that several files in this patch didn't end the license/(c)
block with a blank comment line so these were added as the vast
majority of files do have this last blank line. Simply there for
consistency.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Id5b7ce4f658fe87132f14139ead58d6e285c04d4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/15192
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
Get full regex match using ".group(0)" method.
Otherwise a non-iterable MatchObject is passed
to get_route_nic_numa() which causes an exception.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: Ief8b08387e4233d42b5ac32bd4d7394596aabd78
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14649
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
For each generated fio job section "filename=" field try
to figure out what's the most dominant NUMA node in use
and use it for fio "numa_cpu_nodes" and "numa_mem_policy"
settings.
Change-Id: I96fda436dda8d4009dc191bf7c0c836e5b53a1a3
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13514
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
This use case was missed during the initial refactor introduced via
008f8a8617. CI depends on it so allow to specify the target location
of the fio configuration and allow to skip call to the main perf
wrapper.
Signed-off-by: Michal Berger <michal.berger@intel.com>
Change-Id: Ie41f9db40769980047f42475ce74e61c374c364c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14590
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Use fio "offset", "offset_increment" and "size" to
split target file into chunks, so that each fio
job clone (specified by "numjobs") gets it's own
part of the disk to work with.
This is especially helpful in case of sequential
workloads run with numjobs > 1 and helps to keep
the workload to being as close to sequential as
possible.
Change-Id: I1ca88ae56136d22cf396f464d78b05eff5c07a2a
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13515
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This is consistent with the use of terms in other parts of SPDK and fits
with the code living under module/
Change-Id: If182f7cf2d160d57443a1b5f24e0065f191b59b2
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13919
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Use collect-bmc-pm to gather power usage stats during fio workloads.
Signed-off-by: Michal Berger <michal.berger@intel.com>
Change-Id: I20d1f3009c8a32c3927ad2cf2f932a8e97d3e7c5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14164
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This script is a wrapper around ipmitool which attempts to extract
power statistics from the BMC. It's mainly based around DCMI spec
to make sure it's common for most of the platforms that we use
in our CI. If given BMC does not conform to DCMI, there's a fallback
in place which attempts to find proper sensor in the SDR which may
report overall power usage of the underlying system.
By default, current ("NOW") reading is extracted in context of DCMI.
Different intervals may be defined, and when matched with supported
averaging time periods, special version of the command will be used
to extract additional avg, min, max information for given time (e.g.
current, max, min, avg readings from last 1m). For the SDR fallback,
only current reading can be extracted.
When terminated, script dumps all readings + their averaged value
into separate .txt files.
Change-Id: Ifc8c1defe862254864d69de7edf5cce635aff258
Signed-off-by: Michal Berger <michal.berger@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14144
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Signed-off-by: Michal Berger <michal.berger@intel.com>
Change-Id: I96df5f21f04b9196083f91783f8dd9cc4c6920d1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13688
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
$fio_extra_conf can either point at an existing file or be an
attached stdin the fio_conf() should read from.
Signed-off-by: Michal Berger <michallinuxstuff@gmail.com>
Change-Id: If902262b0100fb056491928b3f667ab15e6e0024
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12429
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The wrapper glues execution of the perf/vhost tests in as simple form
as possible. The arguments are meant to be passed either via env or
the cmdline in a keyworded argument fashion. All defaults are
embedded inside the configuration which is built by the wrapper
itself.
https://trello.com/c/HSoRtQkO/401-deprecate-vhost-performance-python-helper-script
Signed-off-by: Michal Berger <michallinuxstuff@gmail.com>
Change-Id: Iad94bfdd65cb8871b819351ddae65e647621fb30
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12400
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Make sure needed drivers are loaded before we start
the test.
Change-Id: I93e16a2266f99e7bfa6fffaede460c6230659872
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13616
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
Update PCM binary paths and executable names are these have
changed some time ago.
Update README.md with an explanation about int variables
for "pcm_settings" option.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I8270766ff2c429623a29e4c12427a3dd7e45f229
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13511
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
If SIGTERM does not work - use SIGKILL and clean up
any remaining socket files.
Change-Id: I1a4f2e49a8a43f3eed19e09e16d4ee3420cd31f7
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13739
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
"num_jobs" is described as required parameter in README.md
but not included in example configuration file.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I1077d027d6c7dbee49afa1df4345b4dd478b5ad6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/13615
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Michal Berger <michal.berger@intel.com>
Use posix sockets by default when running tests.
For now we only want to test with this socket type
and ssl socket support may be added later if needed.
Change-Id: If8b125518cf1c01a841276b58fa7ca7799aeb229
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/14353
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@nvidia.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This is to add core_limit parameter to scheduler by RPC.
Signed-off-by: Jaroslaw Chachulski <jaroslawx.chachulski@intel.com>
Change-Id: I0570d24e9ae67ccde64e5f996706fefd2e403086
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12623
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
IDXD has always been used everywhere but technically it stands for
the driver, not the HW (Intel Data Streaming Accelerator Driver)
where the X comes from "Streaming Accelerator" somehow. Anyway, the
underlying hardware is just DSA. It doesn't matter much now but
upcoming patches will add support for a new HW accelerator called
the Intel In-Memory Analytics Accelerator which we'll call IAA and
it will use the same (mostly) device driver (IDXD) as DSA. So, calling
the HW what it is will lessen confusion when adding IAA support.
This patch just does renaming for the accel_fw module and associated
files (RPC, etc).
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ib3b1f982cc60359ecfea5dbcbeeb33e4d69aee6a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11984
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
As introduced in 25bc221cee:
listeners for created subsystems should also be added
to discovery subsystem.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: Id37854ea9a7877eb3e4eb37675d6918ef2931e7e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12676
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Spread out used block devices evenly between
used initiators and then between initiators NIC
interfaces, so that in result each initiator
connects to the same number of subsystems.
Previous version had problems spreading block
devices / subsystems between interfaces in case
division remainder was not 0.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I045dc9313b0613685fc997f821fe66238026a645
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12732
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Save Initiator addressing information in Target object.
This will be needed later to properly spread created
subsystems between initiators and NICs.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I9e5545b7847bb16f3ce3d0ee56038003fda74e6d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12731
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Always reload ICE driver after tests with ADQ enabled.
This is to reset tc qdisc and filter settings and make
sure they don't affect future tests.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I70b94ef236741fe81870954f9901e02b9b5aadb9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12622
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Use different file to save calculated CPU utlization
and do not modify original SAR output.
Change-Id: I415242a5610f1c2a43a038baafa8dcc4f9e8fae2
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12526
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Move sar output file generation into measure_sar
function and pass a file name prefix instead.
More than one file will be created by the function
based on that prefix.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I671887d4d232821c0de19eb338150d30201be204
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12525
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Kamil Godzwon <kamilx.godzwon@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Re-phrase "waiting" message a bit and add another
message notifying that measurements are actually starting.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I55d8ed761bf45a590322cffc5b776a44774977dd
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12522
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
After 7610bc38d, python modules are now located in the python/
directory. That patch also updated PYTHONPATH assignment in most of the
scripts, but one of the perf script and some docs/messages were missed.
Change-Id: Iff3588526f2a382e599f5734d38fc32c15a7bf56
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12223
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Fix pylint findings:
- R0201 Method could be a function
Signed-off-by: Pawel Piatek <pawelx.piatek@intel.com>
Change-Id: I1b9141b9ab150e20fdcd63510b484c6be514efb5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12137
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Up until now, importing an SPDK RPC python module was just a matter of
`import rpc`. It's fine until there's another module called `rpc`
installed on the system, in which case it's impossible to import both of
them. Therefore, to avoid this problem, all of the modules were moved
to a separate directory under the "spdk" namespace.
The decision to move to a location under a separate directory was
motivated by the fact that a directory called scripts/spdk would look
pretty confusing. Moreover, it should make it also easier to package
these scripts as a python package.
Other than moving the packages, all of the imports were updated to
reflect these changes. Files under python now use relative imports,
while those under scripts/ use the "spdk" namespace and have their
PYTHONPATH extended with python directory.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: Ib43dee73921d590a551dd83885e22870e72451cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9692
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
SPDK has settled on what the optimal DSA configuration is, so let's
always use it.
Change-Id: I24b9b717709d553789285198b1aa391f4d7f0445
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11532
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I80e1fdb8b0a3b944ab6efdd21187cef07b685c29
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11271
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Add configuration options to enable using IDXD
for data digest during NVMe-oF performance testing.
Change-Id: I54d443c35c67e0331e3d6ec4aecb577fc7f544c7
Signed-off-by: John Kariuki <John.K.Kariuki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10282
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: I72fc8cb42f57d3272a08a6cefc58b2fa5eb26419
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11094
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
As described in Python documentation:
It is not guaranteed that __del__() methods are called for
objects that still exist when the interpreter exits.
Because of that class instance objects were not always destroyed
after tests.
Change-Id: I10f05a480cde37d274d6475efdf47d094cab7cb9
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11136
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: I780568b9c95a47038278c3ed19fb08228a48fb9c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10740
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
TypeError: ethtool_after_fio_ramp() argument after * must be an iterable, not int
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: I12403967b5b8ce7282c65296a54e00bd047cf903
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10367
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
When I use a single json config to run 4k and 64k together, the IOPS
for the 4k test were lower than expected because the script is using
metrics from both the 4k_64_randrw_m_100_* and 64k_64_randrw_m_100_*
to calculate the average metrics because 4k_64_randrw_m_100_* is in
64k_64_randrw_m_100_*. Fixed issue by checking, if the result file
startswith the name of the fio config file.
Change-Id: I630385c34223b38694d7e2bb578779627c89866d
Signed-off-by: John Kariuki <John.K.Kariuki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10127
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
A temporary workaround for issues seen when using "adq_enable"
is to set channel-pkt-inspect-optimize on before fio ramp_up and
turn it off when ramp_up is ending.
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: I74f71d11e3b9d1a064b36de8acc7a2a23f51a34b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9879
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
* Added sleep as sugested in config guide
* Moved adq_configure_tc() before nvmf_create_transport()
* Added extra logs to output
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: Icc253b98a0fadbe917e912342f91e2bc5ca5064b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9703
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: Ibcc7a77d1ebcc013b5050564fcc31b23b1202912
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9840
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: I1a4d32de6a83800cdcd65dde3895a36731c52838
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9710
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: Ia858a47e51a6ef4a0fba1dc1e68d314b27e20342
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9276
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Do not print ETA output. This pollutes logs when long
benchmark tests are run.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I0dfe30fdd727decb4d81be6b530e675bc1f4518c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9379
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Add option to enable gathering BPF traces while
running the test.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I9ea317a37c3638def40a525eca06f2d8325a74c2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8644
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add exceptions to results parsing and fio run functions
to better inform what's the cause of the failure.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I94e51cb8f77515f7d26a75501011d6111820ae56
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8742
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Enable "kernel_engine" option for Kernel Initiator
class to enable ability to use io_uring engine on
initiator side.
For NVMe-oF this has limitations as apparently it's
not possible to enable polling on the initiator side,
which in turn makes fio "hipri" option also not
possible to use.
Adding #TODO sections with notes in case this is
later fixed in Kernel NVMe driver.
Signed-off-by: wawryk <maciejx.wawryk@intel.com>
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I31da52946692015237263abc77d8425b5eae5b98
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8134
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ie46df6e4f52b59941a90eeb786954fe7d5f1d089
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8040
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
nvmf_subsystem_add_listener() in rpc/nvmf was modified
by 64debe0453 and the
change was not reflected in performance scripts.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I7bb8c39ab225421964e37883aa7b0f824e8df683
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7978
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Added 'rate_iops' FIO option to the performance scripts.
This will be used during tests where limiting factor
has to be artifically imposed, rather than come from
the target/initiator system or enviroment.
One case for this are scheduler tests, to limit
each connection and balance the threads accordingly.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I10bb09be9205a8b7ba90b36cd4e0bf922b0ecbc3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7840
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Signed-off-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Change-Id: I9b9f8c9e407425fdab1e84050354481ad76c19c2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6655
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: John Kariuki <John.K.Kariuki@intel.com>
Rename to target_nic_ip to better match NVMe-oF
terminology.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I0644410cfb063eeea740c54f5860aeefdb52d52d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7089
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
SPDK directory needs to be copied to initiator systems
earlier for set_irq_affinity to run.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I0f9ade02e58c9224e0b2ddc75117baaf653be614
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6776
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Need more investigating how to properly enable ADQ
for Kernel mode. Do not run Kernel + ADQ configuration
for now.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I700ef417b9b398c067a586a1a5ad9947a92057ad
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6566
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Readme was frequently missed when adding new stuff or
updating the performance script, and it is out of date.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I1710473be576ffbcc2fa8e3701b196bd46cf6654
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6538
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Create a default traffic class (tc0) with minimum
needed number of assigned threads and a priority class
(tc1) with number of assigned threads equal to
number of application threads.
Finally run set_xps_rxqs to configure symmertic queues.
set_xps_rxqs script used from Intel ICE driver
package available at:
https://downloadcenter.intel.com/download/29746/
Intel-Network-Adapter-Driver-for-E810-Series-Devices-under-Linux-
Change-Id: Ie0f2db266621a9dabb1621344bfdc5fa64fee03c
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6537
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
There are multiple cases for counting number of CPU threads
on Initiator side. Keep track of num_cores in all of them.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I4b8d1d79a2aa17706d206b149c1c8e8816ae2ef5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6536
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Set busy_poll to 0 for non-ADQ. Having it enabled with
this value results is huge latency increase.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: Ic68ed2b7dc19b8d4b274ce8622194489693863cb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7480
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
num_cores name was misleading, as the parameter actually
contained core mask (or core list). Create separate
class attributes with core mask and number of cores.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: Ibfae7770aea2f2c1c720abf567400deb50028ab4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6535
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Save info about subsystems created subsystems (target
side) and remote subsystems (initiator side) into
a list.
Change-Id: I7ec1c6a4d1f75060b69b68e0b8e0dd61789fc9e0
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6374
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Run set_irq_affinity script after irqbalance service
is disabled and manually tune IRQs to be run only on
the CPUs local to NIC NUMA node.
set_irq_affinit.sh script must be manually downloaded
as part of https://github.com/Mellanox/mlnx-tools/tree/master/ofed_scripts
package before running tests.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I67b3c851bcf283caea29ad36f6d4bc0322ca0d27
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6534
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: John Kariuki <John.K.Kariuki@intel.com>
In performance tests always use best performance policy.
Previously this was manually managed on test systems,
but it's better to do this automatically every time.
Change-Id: Iff81863cf8d9cc713a3c4cce1d8edf7ebbf81c84
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6373
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Modify CPU power management settings to achieve high,
consistent results.
Change-Id: I3602ae7523c5b83878238928caaeb453f7d2533e
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6372
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: John Kariuki <John.K.Kariuki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Tune sysctl parameters for TCP testing. Restore previous
settings after tests have finished. For ADQ-enabled tests
also set proper value for busy_read option.
Commit includes a fix to initiator exec_cmd() method to
allow using command parameters which contains whitespace,
otherwise it's not possible to set some of sysctl params.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I3376b69b8d7c0d8a282765db4fe55824f55f9e05
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6265
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: John Kariuki <John.K.Kariuki@intel.com>
Disable all unnecessary services which might affect
tests performance.
Managing services implemented in a very simplified way
usign subprocess and configparser modules (because json
output is not available). Proper implementation would
need to use a proper dBus API, but this seems like an
overkill for such a script.
Change-Id: I72feec4293b77442a9d2c9b4afaa032df1c4d5e1
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6264
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Configure NIC settings as per ADQ configuration guide.
Change-Id: I957aada267474c2a1448c89a1b7c81d4dd261ca6
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6263
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: If2784b74ece6c48b81cc53e63412cd2bc618ffef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6262
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Use common method name and parameters for calling
subprocesses for local (Target) and remote systems
(Initiators) instead of using "check_output" (from
subprocess module) and "exec_command" (from paramiko)
separately.
Having these functions wrapped by a single common
method will allow to create common methods in Server
class more eaisly, instead of creating two copies in
Target and Initiator classes.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I1c10f6a88f3d7300c227e969ad6fd901763ac52c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6261
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Parse the config file for "adq_enable" flag and enable
the option in SPDK Target and SPDK Initiator configuration.
At this point the flag has no effect on the generated
traffic, as the system and priority queues are not
configured properly. These settings will be added
gradually in following patches.
Change-Id: I5d7bc892f3aa7bbe691b7e0983294b56fcf994f5
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6260
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Get detailed info about NICs installed in servers. This
is using lshw utility to make things easier and not
implement the whole logic for parsing /sys objects and
pci.ids listing in system.
Change-Id: I97871fdc9feaae1c2485574a7b488b88ac3afc4f
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6259
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
The number of options for test execution grew high,
and we still need to add more. This results in a lot
of parameters to pass around in constructors, which
is hard to read and causes pylint to complain.
Instead of passing each option individually as a
separate parameter, pass them as dictionaries just
like they're defined in .json config file. This
makes managing the default values a bit harder, but
is more readable.
Change-Id: I5d88a2b7fe51d2df93edd9130678a937d34facdd
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6207
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Interface names will later be needed for additional
test options.
Change-Id: Ic16d305a97087ab1fdc35d5fd5a3d1ed2a021d90
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6206
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Community-CI: Mellanox Build Bot
So far the information about remote target IP addresses was
stored in "nic_ips" attribute. Add a new "remote_nic_ips"
attribute to be able to differantiate which IPs are local
to given Server class object.
Change-Id: I03dac140241341996674b350c51c18da6e2ee447
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6205
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Signed-off-by: Simon A. F. Lund <simon.lund@samsung.com>
Change-Id: I039a2e22a665e0d52082e6876f2c7c1cd9a336c1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6386
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
If config without this field was used then
script resulted in KeyError exception.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: Icf0b270d28dcc6bf44b66c4b9ed583a6b3ef08b6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6204
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Standard lib modules first, then pip installed modules
and local modules last.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: If0159fad29bab5bef0b69aa803e3cea429cc5f25
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6202
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Pawel Piatek <pawelx.piatek@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Using shell=True was unnecessary, as it spawned additional
shell process for any subprocess with this option set.
We don't need that in this script and it's generally
discouraged.
Also removing check=True from some calls as don't have
these subprocess calls in try/excepy anyways.
Change-Id: Ibb9b5d71119c9dd877209ea77b8351f9b610cade
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6046
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Instead enabling each measurement (cpu/power/memory) just
use a single flag and enable them all at once.
Change-Id: I8a639b697285aa741f28b5ddec11ce70c34fc760
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5980
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Use terminate() instead of kill() to exit more gracefully.
Using kill() resulted in (sometimes) output not being saved.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I3ff1dec8cb0804f6e0674c5ed61bbe4ec9ea70ef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6045
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
"measure_*" threads in script use the same results dir
as the results parsing function. To avoid race try to
create results destination directory early.
Change-Id: Ic391a7c2fb3decff64f1fdf51782abb940706d38
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6044
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Enable pcm-power measurements with appriate option.
This will be used for scheduler tests.
Signed-off-by: Karol Latecki <karol.latecki@intel.com>
Change-Id: I57acc9905c6f1acd7bc3ecdbf886b209a2cdb653
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5979
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
