Apparently there's a data race with the setup.sh script,
that may unbind the PCI device before the mount is visible.
Change-Id: I71a349a10a74e29405e3537c513f284acfbd39fb
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/435259
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Chandler-Test-Pool: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Initial support for softare AESNI_MB DPDK driver only.
Have tested (both aesni and QAT seprately and concurrrently) on underlying NVMe devices
with bdevio and a bdevperf script that runs IOs from 512B to 128K each with Q depths from
1 to 512 in powers of 2 for 30 seconds each run.
QAT can be included in the code (but not makefile) and marked as experimental
until we are ready to test in CI. It works well on 2 systems but is a big PITA to get
the hardware setup and configured for use with DPDK (IMHO).
Change-Id: If518c3df8e74e00efa18afdf194824c5e69778fc
Signed-off-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/403107
Chandler-Test-Pool: SPDK Automated Test System <sys_sgsw@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
'-s' option is usually associated with the memory size,
but our ioat/perf and nvme/perf use it for io size.
To keep those consistent:
'-s' option (io size) was be changed to '-o'
'-d' option (mem size) was be changed to '-s'
Change-Id: I97cef4c0a4e6e902277dd50dfb43bde420a6427e
Signed-off-by: Dariusz Stojaczyk <dariuszx.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/422654
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Chandler-Test-Pool: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Users can set specified Admin commands or IO commands with
error status, when submitting new commands which are already
set with error status, the commands will return to the caller
with specified error code. So that users can emulate some error
status for their error condition code path.
Change-Id: I4b93c7e4f2b15a659da73b39e26bfa162eb5214e
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/410870
Tested-by: SPDK Automated Test System <sys_sgsw@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
