This patch adds the framework for a discovery
service in the bdev/nvme module.
Users can specify an IP/port of a discovery service.
The bdev/nvme module will connect to a discovery
controller, get the discovery log page, and then
register for AERs. It will connect to each
subsystem specified in the initial log page.
AER completions will trigger fetching the log
page again, at which point new subsystems will
be connected to, or removed subsystems will be
detached.
This patch does the following:
* Adds the new start_discovery RPC
* Connects to the discovery controller
* Gets the discovery log page
* Registers for AERs
* Detach from discovery controllers at shutdown
Subsequent patches in this series will:
* Connect to subsystems listed in discovery log page
* Detach from subsystems that were listed in earlier
discovery log pages but subsequently removed
* Add a stop_discovery RPC
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I54bfa896a48c5619676f156b5ea9f2d1f886c72f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10694
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
In the following patches, bdev_nvme_reset() will execute the reset ctrlr
operation on the nvme_ctrlr->thread until completion as bdev_nvme_admin_passthru()
does. Hence change the callback rpc_bdev_nvme_reset_controller_cb
to redirect to the orig_thread by using a dynamically allocated context.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I8ee61857ac034024d00190875740a675ef1db8b0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10073
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
After multipath feature is supported, one bdev will have more than one
nvme ctrlr. Fore ease of view, display each ctrlr's trid info.
Moreover, rename nvme_bdev_ctrlr_get as nvme_bdev_ctrlr_get_by_name here
to keep consistent with nvme_ctrlr_get_by_name.
Signed-off-by: Kai Li <lik271@chinatelecom.cn>
Change-Id: I417506699bbea6ed13dac0fee942749757d2ae47
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10129
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add bdev_retry_count to spdk_bdev_nvme_opts and retry_count to
nvme_bdev_io, respectively.
Set type of both to int because we want use -1 for infinite retry.
Set the default value of bdev_retry_count to zero for the backward
compatibility.
bdev_retry_count is configurable by the RPC bdev_nvme_set_options.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9bc746fcea54aa8722c76f79c70c2ae2b375aa53
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9864
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
retry_count of struct spdk_bdev_nvme_opts controls the number of retries
in the transport layer, and is set to transport_retry_count of struct
spdk_nvme_ctrlr_opts.
The next patch will add bdev_retry_count to struct spdk_bdev_nvme_opts
to control the number of retries in the bdev layer.
For clarification, rename retry_count to transport_retry_count of
struct spdk_bdev_nvme_opts. Then deprecate the retry_count parameter
and add and use an new parameter transport_retry_count instead for
the RPC bdev_nvme_set_options.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I0689c54aa1c96ee99d24236e8ff1a594ad7208e4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9924
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
You can now detach specific paths based on the host parameters. This is
useful for two paths to the same target that use different local NICs.
Change-Id: I4858bfda7d940052ca77ffb0bbe764a688fb315d
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9827
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
The all setters of the reset_cb_fn use boolean as the result eventually.
Using boolean as the result earlier makes the code simpler and the
following patches easier.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9ec4f670ed7a000a824ab7e261bab07a3dc21f43
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9814
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Pointer 'ctx->req.multipath' returned from call to
function 'strdup' may be NULL. Reported by Klocwork.
Change-Id: Id4a188ec5340f02c9bd0643db0acb03409dd5829
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9843
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Specifying only a transport id is not enough. We need to be able to
describe the host parameters too.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Iadbea553aee4b38e7cacab0b486e7e5746d0d1ab
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9825
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This is the currently active path identifier in a failover scenario. The
path is defined by more than just the transport identifier, so fix the
name.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I682c6f4c54f75307e2615bf80e70358180d99fe2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9576
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The new path must differ in some way.
Change-Id: I98fd2b2cb3220b482efe0a19bfce94ec4e72bec2
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9418
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This parameter may have the values "disable" or "failover". The default
is failover to match existing behavior. In the future we expect to
change the default behavior to disable.
Further, we expect to add an "enable" option soon to do full multipath.
Change-Id: Iebbdc9b95f23101f18d64e085933463498e627be
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9343
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
It can match by any provided parameter to remove paths.
Change-Id: I5e7a87342bbb90943dc97fb52f142814fcf0acfa
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9453
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Instead of storing an spdk_nvme_transport_id, store the object that
contains it. This will make a few later patches easier.
Change-Id: I36b74889fe39af3b7ab2b900fb3ea4b3f39e1f83
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9484
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Enable dump of transport stats in functional test.
Update unit tests to support the new statistics
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I815aeea7d07bd33a915f19537d60611ba7101361
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8885
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch enables us to aggrete multiple ctrlrs in the same NVM
subsystem into a single bdev ctrlr to create multipath.
This patch has a critical limitation that ctrlrs which are aggregated
need to have no namespace. Hence any nvme bdev is not created.
However it will be removed in the next patch.
The design is as follows.
A nvme_bdev_ctrlr is created to aggregate multiple nvme_ctrlrs in
the same NVM subsystem. The name of the nvme_ctrlr is changed to be
the name of the nvme_bdev_ctrlr.
NVMe bdev module has both the failover feature and the multipath
feature now. To choose which of failover or multipath to use, add an new
parameter multipath to the RPC bdev_nvme_attach_controller.
When we attach a new trid to the existing nvme_bdev_ctrlr, we use the failover
feature if multipath is false, we use the multipath feature if multipath is
false.
nvme_bdev_ctrlr has a list for nvme_ctrlr and it is guarded by the
global mutex. Callers can query nvme_ctrlrs from a nvme_bdev_ctrlr via
trid as a key. nvme_bdev_ctrlr is not registered as io_device.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I20571bf89a65d53a00fb77236ad1b193e88b8153
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8119
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Following the last patch, include hostid into ctrlr_opts rather than
passing it as a parameter for bdev_nvme_create().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I0d04db1c5767ec76a9a7cd255c3a8d56b0b8f583
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9344
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@gmail.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This only existed to share code between OCSSD and regular NVM
namespaces. Now OCSSD is gone, so just merge the files into bdev_nvme.
Change-Id: Idb73cc05d67144de5dd20af8db24c8f6974d10a7
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9337
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Do simple validity checks first, then check for duplicate controllers.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ic21d64574b37a3d9148e5cd6d5a7599449ea8fe1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9341
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Jacek Kalwas <jacek.kalwas@intel.com>
bdev_nvme_create() is called only by a single caller and hostnqn is
just copied to ctrlr_opts even if it is passed separately.
Hence include hostnqn into ctrlr_opts rather than passing it as a
parameter for bdev_nvme_create().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I75b640bcecefa94950b0c19936fab0571c428125
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9332
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@gmail.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Implement bdev_nvme_reset_controller rpc, which allows the NVMe
controller to be reset over RPC. Implement bdev_nvme_reset_rpc()
which starts the reset of the controller and returns the result of
the controller reset via the callback function after it completes.
Signed-off-by: Jonathan Teh <jonathan.teh@mayadata.io>
Change-Id: Id98d5e56feb315b7e44e9bb5e5f495e9b1cd1de0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8456
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Replace two helper functions, nvme_bdev_first_ctrlr() and
nvme_bdev_next_ctrlr() by an new helper function nvme_ctrlr_for_each().
This will make us easier to guard data structure correctly in the
following patches.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibd81286e454fd6127fd150a7d48d8381bd1b89d3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8721
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This object aggregates multiple I/O qpairs for their completion
operations and may be a higher layer object. However, the
aggregation is only to poll completions efficiently. Hence if we
follow the new naming rule, nvme_poll_group is better than
nvme_ctrlr_poll_group and nvme_bdev_poll_group, and rename
nvme_bdev_poll_group by nvme_poll_group.
Besides, many functions in NVMe bdev module have a naming rule,
bdev_nvme + verb + objective
Follow this rule for a few functions related with nvme_poll_group.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5e5cb6001d4a862c2121b7265cbbffe0c2109785
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8720
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This object is per I/O path and will be aggregated by an new upper
layer object.
Hence rename nvme_bdev_ctrlr by nvme_ctrlr. Then the following patches
will add nvme_bdev_ctrlr as a different upper layer object.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ieed634447785cc98140b3d49c52a2c753988ece7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8381
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This makes use of newly added spdk_bdev_wait_for_examine(),
to only respond to RPC when bdev was fully examined.
Fixes#1760
Issue above was triggered in DD tests where application
finished before the examine had a chance to fully finish.
This patch addresses it by making sure that nvme attach
RPC waits for completion of the examine.
Later patch in series adds the bdev_wait_for_examine RPC
to multiple static configuration files. Making sure similar
issues do no occur for bdev modules which do not have changes
in their RPC as here.
The issue does not occur for JSON configs generated from apps,
see patch:
(e57bb1af)lib/bdev: build bdev_wait_for_examine into subsystem
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ie3ca2933af97a40ae01ecc3eefe2161d2d34c602
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5483
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Check if qpair has a poll group during the connect process,
use poll group's statistics or allocate own structure per
qpair. That is done due to not all applications use poll
groups and we want to avoid "if (qpair->group)"
conditions in data path.
Admin qpair always allocates its own statistics
structure but the statistics are not reported
since this qpair is not attached to a poll group.
Statistics are reported by spdk_nvme_perf tool
if --transport-stats and in bdev_nvme_transport_statistics
RPC method.
Change-Id: I58765be161491fe394968ea65ea22db1478b219a
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6304
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This will make us easier to maintain the operation to delete
nvme_bdev_ctrlr and its trids. The added unit test cases guard us
from degradation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I400d4092020e89bacaebc7be045a456b8760ed8d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6688
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Function bdev_nvme_create accpets new parameter - ctrlr
opts which is passed and filled by RPC handler. That
will allow us to add config parameters for other ctrlr
options with minimal changes.
Change-Id: I96ac1b21e7a3816c652765cddade75423eb843ca
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6023
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
According to kernel, use an inline function spdk_nvme_bytes_to_numd
to transfer paload_size form bytes to numer of dwords.
Signed-off-by: sunshihao <sunshihao@huawei.com>
Change-Id: I8b9ded122bbf4a3c8e46988993ea52404783c0b0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5926
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Add keep alive timetout parameter in bdev_nvme_set_options.
NVMe bdev can set this value especially when we test with
bdevperf.
Fix github issue: #1690
Change-Id: I255c935671b74cdb615a8d393e7d7e84524f3c23
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5306
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
There are many duplicated codes about sending response for writing bool result.
That we need a function to do this.
Then we can reduce many codes.
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: Ic439111b1e9ca1013f8c657ab925f0c27a7be699
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5033
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Analyzer treats these as warning, they are unused.
Issue:
bdev_nvme_rpc.c:706:7: warning: Although the value
stored to 'rc' is used in the enclosing expression,
the value is never actually read from 'rc'
if ((rc = spdk_nvme_ctrlr_reset(firm_ctx->ctrlr)) != 0) {
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
bdev_nvme_rpc.c:851:8: warning: Although the value
stored to 'rc' is used in the enclosing expression,
the value is never actually read from 'rc'
if ((rc = spdk_bdev_open(bdev2, true, NULL, NULL, &desc)) != 0) {
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
nvme_rpc.c:375:10: warning: Although the value stored
to 'rc' is used in the enclosing expression, the value is
never actually read from 'rc'
return rc = val->type == SPDK_JSON_VAL_STRING ? -ENOMEM : -EINVAL;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: I1d58db97b00ac2d102c1a46d7852c2ce3f559fda
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4824
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
There is nothing left here, so remove it.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ib947d42bc577dbebb4650b1be885e05a80f8f8cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4541
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom CI
This will allow us to use this RPC to detach only specific
paths from controllers.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ib52e38aa7d4ea096418a6dc0328481c2e8db6c54
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3070
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This RPC was using snprintf which could potentially
truncate a bad argument silently without alerting the
caller.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I1795b2e4086cbaa45390bd11b189755818b5c9e7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3613
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This allows us to avoid creating a separate rpc just for multipath TRIDs.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I4e83167eaf16e50a72efbd513333a4d09c52be61
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2884
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This patch paves the way for introducing a tailq containing
multiple alternative paths to the same controller.
Change-Id: I13d30c12b8e0ce38eae687f9e76740be1d11e4d1
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3259
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Purpose: To set the priority of the NVMe-oF connection especially
for TCP connection.
For example, the previous example can be:
trtype:TCP adrfam:IPv4 traddr:10.67.110.181 trsvcid:4420
With the change, it could be:
trtype:TCP adrfam:IPv4 traddr:10.67.110.181 trsvcid:4420 priority:2
The priority is optional. We try to change
spdk_nvme_transport_id but not in spdk_nvme_ctrlr_opts since
the opts in spdk_nvme_ctrlr_opts will reflect in every nvme ctrlr,
this is short of flexibility.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Change-Id: I1ba364c714a95f2dbeab2b3fcc832b0222b48a15
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1875
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This was changed to better facilitate thread safety.
In next patch a lock will be held when going over the
cuse devices list.
Now user is expected to pass a buffer of a sufficient size
that will be filled with ctrlr or ns cuse device name.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I3202ef285e427111e3595389619463fda58dbef6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1978
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
All of the error cases for spdk_nvme_transport_id_parse_trtype
were covered earlier, so just make this an assert.
fix kw warning 12653.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: If0eea934764b35d097887b98b0441ae5d7dd3e4f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1953
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
With the JSON configure, the base device will be opened on the
same thread (RPC thread) to handle the JSON operation. Later the
virtual device upon the base device can be opened on another
thread. At the time of virtual device destruction, the base
device is also closed at the thread where opening the virtual
device, it is actually different than the original thread where
this base device is opened through the JSON configure.
Add a thread here to record the exact thread where the base
device is opened and then later route it back to handle the base
device close operation.
Change-Id: Id1299bb0d86db57bce48b9787d7f248d29a6f345
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/974
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
When structure for output of json decoders in not initialized
spdk_json_decode_string may fail trying to free uninitialized
string.
This patch changes mallocs used to allocate context and structure
for output of decoder with calloc.
Fixes#1151
Change-Id: I180b2ec52350b4ca90e7c318b4f2d13af554ec49
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/483107
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
The trtype should be stored as both an enum and string. This is intended to
help pave the way for pluggable NVMe-oF transports.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I6af658d7a17c405e191ff401b80ab704c65497e7
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/478744
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Alexey Marchuk <alexeymar@mellanox.com>
In the case that there is no NVMe bdev configured and RPC is
running, it shall still allow the NVMe options set. Once there
is one NVMe bdev configured, it will not allow the NVMe options
set.
Change-Id: Ib6a527174137a5d4df7babe206d2527e600500c0
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/479489
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Added RPC commands to register/unregister CUSE devices
to NVMe controllers:
- bdev_nvme_cuse_register
- bdev_nvme_cuse_unregister
Additionally two RPC now return CUSE device names:
- bdev_get_bdevs for namespaces
- bdev_nvme_get_controllers for controllers
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I69c4bf41ec8f78a7522894268a67dd733881712f
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/472211
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Due to upcoming change we cannot use the same count
pointer in rpc call and bdev creation function.
With async bdev creation there will be a problem
when freeing context.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I98da89481d7f506161d8adf5a1b2365907385a13
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/468463
Community-CI: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This also requires change of type for count field
in rpc_bdev_nvme_attach_controller_ctx structure
and argument type in spdk_bdev_nvme_create function.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: Ifc679558b0744ada021f5ce367beb83b35f30b3a
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/470135
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The new name comes first, the old name comes last.
Eliminates warnings at app start time for
set_bdev_nvme_options and set_bdev_nvme_hotplug
aliases.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ia5ff3012e97bf59a6ecd9282dfc5cc0796ca7630
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/466967
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is more accurate to what they are, and will make defining library
dependencies much simpler. This change in directory does not affect the
final placement of naming of libraries at the end of time.
Change-Id: Ic48a9233dff564e39ce357a9ea0a111ea2b6414b
Signed-off-by: Seth Howell <seth.howell@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/465454
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Broadcom SPDK FC-NVMe CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
