In json_config test, when there are multiple nvme disks, we see errors like:
ERROR: expected event 'bdev_register:Nvme0n1p1' but got 'bdev_register:Nvme1n1' (whole event line: bdev_register:Nvme1n1:1)
The reason is when there are multiple nvme disks in the system, when
start nvmf_tgt, it will register all the disks in bdev, so there would
be multiple bdev_register events for these disks before we run
create_bdev_subsystem_config. So in create_bdev_subsystem_config we need
add these events to expected events list first.
Signed-off-by: Rui Chang <rui.chang@arm.com>
Change-Id: Ice8f5464975e68ae63fec891ef18dbc7590a9ab5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7858
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Currently we allocate buffers perf each SGL descriptor.
That can lead to a problem when we use NVME bdev with
PRP controller and length of the 1st SGL descriptor is
not multiple of block size, i.e. the initiator may send
PRP1 (which is SGL[0]) which end address is page aligned
while start address is not aligned. This is allowed by
the spec. But when we read such a data to a local buffer,
start of the buffer is page aligned when its end is not.
That violates PRP requirements and we can't handle such
request. However if we use contig buffer to write both
PRP1 and PRP2 (SGL[0] and SGL[1]) then we won't meet
this problem.
Some existing unit tests were updated, 1 new was added.
Fixes github issue #1853
Change-Id: Ib2d56112b7b25e235d17bbc6df8dce4dc556e12d
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7259
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
When we introduce RB tree, getting the closest timed poller is not
O(1) but O(log N). To mitigate such delay, cache the closest timed
poller into thread, and update the cache when its content is changed.
Add unit test cases for this change. They will also clarify the current
behavior of spdk_poller_unregister() and spdk_poller_pause() for
timed pollers.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibb98a54c261859a3210034038d3953e5c93ef8aa
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7720
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Mellanox Build Bot
Some systems may have page size other than 4096 bytes
Change-Id: Id56bb1566fff480edbe1a293121fc7a68c74252a
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7820
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Runtime RPCs such as bdev creation has no chance to wait for
bdev examination to finish. To handle this case commit below
introduced bdev_wait_for_examine RPC, and built it into all newly
saved JSON configurations:
(e57bb1af)lib/bdev: build bdev_wait_for_examine into subsystem
Some tests generate the configuration by hand, rather than
saving it from an existing application.
This patch embeds this RPC into the test configs.
Fixes#1760
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I79f998d722a2d19aa98b78333c64dbd2c1151444
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7861
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Function initiator_json_config is never called with
additional arguments that would fill up the subsystem
JSON.
Handling for the comma is removed.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I6ce5648a0eac29cb0f45d210696edf7977dfe89d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7860
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Use spdk_thread_get_last_tsc() and spdk_thread_get_stats() in
unit tests for reactor. As a result, we can change one inclusion
from spdk_internal/thread.h to spdk/thread.h.
This is the same effort as spdk_poller.
The following patches will move the definition of struct spdk_thread and
enum spdk_thread_state from include/spdk_internal/thread.h to
lib/thread/thread.c.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I24d4a52ecf885b6e7db749616ee1f95b82574dc5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7801
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add {min,max}_cntlid to spdk_nvmf_subsystem, defaulting to 1 and
0xFFEF, respectively, and add nvmf_subsystem_set_cntlid_range() to
allow the controller range to be configured in the range [min_cntlid,
max_cntlid].
Also add {min,max}_cntlid to the nvmf_create_subsystem RPC to allow
the controller ID range to be specified when creating an nvmf
subsystem.
Signed-off-by: Jonathan Teh <jonathan.teh@mayadata.io>
Change-Id: I936db3bb0c9a38569063a6fd3c11df262dfad776
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7322
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
It's only for tcp now, but the transport here is rdma. So there is no need to assert.
Signed-off-by: ChengqiangMeng <chengqiangx.meng@intel.com>
Change-Id: Ieffaac9d31a8f9c79a0d9fd226d74268986b7a77
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7823
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
fio.py simply wraps itself around fio and doesn't do anything that
would require python to be in use. Having it in a simple bash form
makes it easier to integrate it with autotest's common sh tooling
and to debug any potential issues with the underlying tests.
This also fixes#1919 by making sure only proper nvme devices are
selected for the nvmf targets.
Fixes: #1919.
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Change-Id: I111d00df3c7b2517f431cae865e258a665c2ecb3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7684
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This helps in next patch in series where multiple
completions will be executing.
UT is adjusted since one additional poll is required.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Id72377ddef91e40cdbc2bdea6f33c23309b0ca3d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7642
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
During snapshot creation the original blob becomes
a thin provisioned blob that will only the diff of data after
snapshot creation.
Despite the comment in the UT the number of polls before issuing
blob write was hitting blob BEFORE it swapped with new one.
Issuing I/O during this period shall check for io freeze
before checking cluster allocation.
Otherwise bs_io_unit_is_allocated() hits assert for thin
provisioned blob. This is because cluster map of blob is
empty, but properties have not been updated yet.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I742e1a50b14d456ae1e6de13b5111caec3e8322c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7641
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
ctrlr_discovery.c doesn't need this #include.
Including it causes bdev_module.h types to be
emitted to the debug symbols at least with some
compilers, which can result in unwanted abidiff
errors.
The unit tests do need it, so just include it
there instead.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Iad28f9778ce08b11b52325658583ae9032295f3a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7813
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The library itself doesn't need it. The unit tests
do need it, so just include it there.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I9aefd303ae12928d45141029436509f185105bd3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7812
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
- Use consistent cache line size units in KiB across RPC calls
and config files. The KiB units are much easier to use then
the bytes units and are more human readable.
- Properly handle cache start when cache line size is incorrect.
- Add test to check if cache line size value is reported correctly.
- Add cache line size info to JSON RPC documentation.
Fixes#1858
Signed-off-by: Rafal Stefanowski <rafal.stefanowski@intel.com>
Change-Id: Iec9ede85f6884b64605d2d112947b3f175cbd938
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7614
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Older version wasn't providing full support for PMR setup, this one
does.
Rewrite get-pmr such that it supports CMB/PMR sizes greater than 4GB.
Also, since CMB and PMR can coexist in newer versions of qemu try to
detect both under single device.
E.g.:
nvme0:0000:00:04.0:64-bit:prefetchable:0x700000000:0x707ffffff:0x08000000:cmb
nvme0:0000:00:04.0:64-bit:prefetchable:0x400000000:0x5ffffffff:0x200000000:pmr
nvme1:0000:00:05.0:64-bit:prefetchable:0x708000000:0x70fffffff:0x08000000:cmb
nvme2:0000:00:06.0:64-bit:prefetchable:0x600000000:0x6ffffffff:0x100000000:cmb
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Change-Id: Ic159f5c12d3ef39db77617f7d64f825356c255a4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7539
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Passing cpu_mask hints that match only single core were
usefull to prevent any accidents when doing round-robin
in case of 'static' scheduler.
In practice this is not required in case of 'static' scheduler,
the threads will be spread out over all reactors anyway.
This hinders other schedulers which try to respect the cpu_mask
hints, as they would not move the thread to any reactor.
Preventing bunching up less used threads on single reactor.
Drawback of this patch is that poll group names will not match
the cores they are on.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I5fb308362dd045228ea9fcca24f988388854c054
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7028
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Nvme-cli uses NVME_IOCTL_IO_CMDs for "io-passthru"
commands to cuse devices. This patch adds support
for that IOCTL.
Signed-off-by: Curt Bruns <curt.e.bruns@gmail.com>
Change-Id: I20e0ac91ba08fce91bc5da1f4a1e454058cdd1e7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7741
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The nvme cuse IOCTLs are actually creating passthru commands
that can be either IO passthru commands or admin commands.
Renaming the routines to correctly reflect that should limit
the confusion when reading the code. Passthru commands that
are admin commands will go to the spdk_nvme_ctrlr_cmd_admin_raw
interface and passthru commands that are IO will be sent to the
spdk_nvme_ctrlr_cmd_io_raw interface.
Signed-off-by: Curt Bruns <curt.e.bruns@gmail.com>
Change-Id: I8d427fe8b5f503fdb2d193236c77d410d5b13886
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7740
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Purpose: We will also support the kernel idxd driver, so we do not
need export this feature in the module file.
Change-Id: I965e031497920f527962ba187bccd81de6977b8f
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7336
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This is prepared for using the hardware offloading
engine in accel framework. And some fields in nvme_tcp_pdu
needs to be DMA addressable.
Change-Id: I75325e2cd7ff25fe938bea0ac9489a5027e3e0e9
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7770
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This is used to prepare using the accel framework to calculate
the crc32 because some fields in this structure needs to be allocated
in DMA addressable memory.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Ib8def5596e60f4702709da647145c4e2b6d6848f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7767
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
We cannot rely on DSM/DEALLOCATE as a write zeroes
alternative, even if DLFEAT reports that deallocated
blocks will be read as all zeroes. DEALLOCATE is
advisory, meaning that blocks may not actually be
deallocated. In cases where they are not deallocated,
they will not be read back later as zeroes.
QEMU 6.0 started reporting DLFEAT as returning zeroes
for deallocated blocks but for some of our write
zeroes tests, blocks aren't actually deallocated.
We may be able to add quirks in the future if we know
that a controller reliably deallocates blocks, but
for now we need to revert this completely.
Note that since bdev/nvme module now does not support
write zeroes in any cases, we need to disable the
write zeroes call in the unit tests.
Fixes issue #1932.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I79f0673774b621a9ffcc46891728cc7719e34cdb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7723
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This will help us to add unmap split function, also
remove bdev_io_type_can_split() because we changed
to use swith(io_type) ... case now.
Change-Id: I449d6a9f5bf2d0b43dd124bbfc9e1ca2afddc15a
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7516
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Purpose: This patch is used to prepare to add the kernel
idxd support later.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: If89665f95d622c7342ab75050664158ec6fc615a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7330
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
(Note: this patch was previously applied as b32cfc46 and then reverted
as 63642bef.)
Today the in-guest nvme device shows physical_block_size=512 even though
the backend iSCSI bdev supports physical_block_size=4K
iSCSI targets exposes physical block size using
logical_block_per_physical_block_exponent in READ_CAPACITY_16
NPWG is one of the way to let Linux nvme driver set
physical_block_size of the nvme block device.
This patch adds spdk_bdev.phys_blocklen which is updated if the iSCSI
backend exposes physical_block_size.
Later phys_blocklen is used in nvmf to set NPWG and NAWUPF to report
back during NS identity.
Linux driver uses min(nawupf, npwg) to set physical_block_size.
Similarly in scsi_bdev fill lbppbe in READ_CAP16 response
based on spdk_bdev.phys_blocklen.
Fixes#1884
Signed-off-by: Swapnil Ingle <swapnil.ingle@nutanix.com>
Change-Id: I0b6c81f1937e346d448f49c927eda8c79d2d75c0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7739
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
1) use spdk_bdev_get_name() accessor
2) use __SPDK_BDEV_MODULE_ONLY #define
The latter allows nvmf to just get the spdk_bdev_module
definitions and APIs that it needs for claiming bdevs
for purposes of avoiding the same namespace used in
different subsystems.
This also ensures that future changes to structures
like spdk_bdev and spdk_bdev_io will not cause
lib/nvmf so version changes.
Note: we include bdev_module.h explicitly in the
nvmf/subsystem unit tests now, before including
subsystem.c, because the unit tests do depend on
knowing the internal structure of spdk_bdev.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I2f499a741d19f4749eadb402641f28137245fd23
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7738
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
It is already set by nvmf_tcp_req_pdu_init
when we get the pdu. So we do not set it again.
Change-Id: I034bbc46e600afd802457c0b152e303f16bafba3
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7714
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This reverts commit b32cfc467b.
This commit fails the ABI checks and only got through because the checks
were disabled until 21.04 hit.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Id26b8f8ba551193d99b1ccbd31b35378b4095a20
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7731
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Today the in-guest nvme device shows physical_block_size=512 even though
the backend iSCSI bdev supports physical_block_size=4K
iSCSI targets exposes physical block size using
logical_block_per_physical_block_exponent in READ_CAPACITY_16
NPWG is one of the way to let Linux nvme driver set
physical_block_size of the nvme block device.
This patch adds spdk_bdev.phys_blocklen which is updated if the iSCSI
backend exposes physical_block_size.
Later phys_blocklen is used in nvmf to set NPWG and NAWUPF to report
back during NS identity.
Linux driver uses min(nawupf, npwg) to set physical_block_size.
Similarly in scsi_bdev fill lbppbe in READ_CAP16 response
based on spdk_bdev.phys_blocklen.
Fixes#1884
Signed-off-by: Swapnil Ingle <swapnil.ingle@nutanix.com>
Change-Id: I0b6c81f1937e346d448f49c927eda8c79d2d75cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7310
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This check was disabled after 21.01 LTS to allow for
clear break of SO versions. Now that SPDK 21.04 is being
released, this test should be reenabled.
See following patch for details:
(e4070ee0)so_ver: increase all major versions
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I8a299a340338e7a2ab3439b81153818778b4c93a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7616
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
test script 'test/interrupt/reactor_set_intr.sh' will
do various reactor set intr operations on interrupt_tgt
without spdk_thread and with spdk_thread.
Change-Id: Ie5af1dc68b0272c34a91e8a66b78088c3794907c
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7348
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
There are three modules implementing the bdev-zone API:
bdev_nvme, bdev_ocssd, and vbdev_zone_block.
For all three modules, the number of zones can be calculated using:
block_count / zone_size.
To avoid this calculation being performed everywhere, create a helper
function in bdev_zone.h, together with the other zone APIs, such that
a user can easily get the number of zones.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I2967b15a604ab8bf4420588e7510b9820762f925
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7451
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
tcp transport doesn't send a response capsule when
c2h_success is set even if cdw0 or cdw1 are non-0.
Signed-off-by: Ed rodriguez <edwinr@netapp.com>
Signed-off-by: John Meneghini johnm@netapp.com
Change-Id: Ieba81fcc50342a2009f7931526e6f8392e26b6a5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6808
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
New UT verifies number of extent page writes for
thin provisioned blobs.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I6b52195d26c3c1414ca862b03e8a3043bbe29b42
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7017
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
This patch addresses couple issues:
1) Before issuing the md syncs the previous steps in test left
blob state in dirty state already. The resize never had a chance
to apply. This patch adds a proper md sync and polls for completion.
2) Changing blob state is something that should be done via API.
In order for dirty state to apply immidietly set_xattr is now used instead.
3) Verify test state in callbacks to make sure not only the number of
completions is correct, but their order.
This patch is introduced because of the test originally worked
only because of the extent pages always writing out its pages.
The second sync always was delayed because of this.
Meanwhile that should not be the case, since no MD or EP modification
was done.
Later in the series Extent Pages are fixed, but this test remained incorrect.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Iac17c27f6ff83f2b79835aa6e48472d5293c44d0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7233
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
This function finds a placement_id that does not have a group
associated with it.
Change-Id: I1306690e980fd4661f46dba9fb283f048a962eba
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7223
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Added nvmf_tcp_init() to run tcp through physical E810 network card.
If there is not E810 in system, tcp will still run on virtual eth.
Change-Id: I9a983c92175b27c45457682d42d72ef307fef260
Signed-off-by: wanghailiangx <hailiangx.e.wang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6932
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Reviewed-by: <qun.wan@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
When the format command is issued, the kioxia drives responds with "NS Attr change" notices.
In the callback function of the notice, the CQ Head Doorbell is updated twice with the same
value while issuing the Active NS list & identify NS commands.
Fixes: #1701
Signed-off-by: G.Balaji <gbalajieie@gmail.com>
Change-Id: I8cc80fba0a226c22753e605ef3129602a9313ce7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7149
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Also update the UT.
Change-Id: I6086bf4cafca8a917a467490955d7df0ba8930d5
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7495
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is done in order to distinguish between different flavors more
easily.
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Change-Id: I9740677c878a8e6ad5abb3e2b5c22b9d41d59fc6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7117
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This is done as part of a request to run tests on PMR-capable VMs
in the CI pool.
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Change-Id: Icf64bf07cd81945e519b0d212ca126d79c3fecbc
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7020
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Since the maps are unique to modules, they can store the group_impls
directly.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I7f11db558e38e940267fdf6eaacbe515334391c2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7222
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This allows for different policies per module, as well as overlapped
placement_id values.
Change-Id: I0a9c83e68d22733d81f005eb054a4c5f236f88d9
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7221
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Test scenario is as follows.
Some iSCSI initiator sends a Data-OUT PDU sequence such that the size of
the data segment of any Data-OUT PDU is not block size multiples.
Test if such complex Data-OUT PDU sequence is processed correctly.
Desired Data Transfer Length is 5 * SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH / 2.
Number of Data-OUT PDUs is 4. Length of the data segment of the first two PDUs are
SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH / 2 - 4. Length of the data segment of the
third PDU is SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH. Length of the data segment
of the final PDU is SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH / 2 + 8.
Three data buffers should be used and three subtasks should be created and submitted.
The test scenario assume that a iscsi_conn_read_data() call could read
the required length of the data and all read lengths are 4 bytes multiples.
The latter is to verify data is copied to the correct offset by using data patterns.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5e3939d07cd4f50fe3dcf659a18a9f8fcbe01e07
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6584
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: Mellanox Build Bot
Test sharing data buffer among multiple Data-OUT PDUs.
Allocate real data buffers and the iscsi_conn_read_data() stub writes
data patterns into them.
The data pattern is to write offset per 4 bytes. This requires read
length to 4 bytes multiples but the requirement will be acceptable.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I87c673c3bb0ada2afebb9332af9525cd9d7388f2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6568
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
This prepares for an upcoming patch to fix issue #1701 which
requires handling async events outside of the check
completions loop.
Fixes: #1701
Signed-off-by: G.Balaji <gbalajieie@gmail.com>
Change-Id: I4985d814903143511383172b1a443580db33a78f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7416
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
We can return error status when processing RELEASE2 without
a reservation, also add a UT to cover this case.
Fix issue #1898.
Change-Id: I56ffa8eabfc0409307500f8740cb627aab9d2f0b
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7379
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This reverts commit aaac48880d.
This patch was showing issues with SPDK vhost mappings
when handling larger numbers of VMs.
Fixes issue #1901.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I81bd311d26037dcb9340d85abcb4ea45b20a5170
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7424
Community-CI: Broadcom CI
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is necessary to the following patches to test reset continuation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I20e0a6b96694eb06adadfbe8e20f73380645ea43
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7326
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
It is more readable to use const variable rather than raw number.
memset is the way to initialize variable size array.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I42f3f34422ea96e06a99bd6cc02e0e91349a4009
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7323
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
Previously when attaching a ctrlr, all namespaces had not been
populated. Hence we had to populate each namespace manually.
It is more normal if all namespaces are populated when attaching the
corresponding ctrlr.
This patch does such change.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I55d9c444c492ba6e44a609eac81b1ef25a7190a8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7313
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Previously spdk_nvme_probe_poll_async() had processed all attaching
controllers. Hence it was not easy to attach multiple controllers in
unit tests.
Besides, add a check to exclude duplicated controllers into ut_attach_ctrlr().
If the target is any SPDK library, we should insert another patch
only to do code movement, but this is a unit test file, and so it
will be acceptable to include code movement in the same file.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9e8eba6a67b2a6d0df384214ff84aa5b0c602217
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7312
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Not only in accel_perf, but also in test event_perf.
Remove them.
Fixes#1895
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: I2af1d9f6f077f3ae775af994567804633fc8f050
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7370
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Look for drives with 2GB of space at minimum.
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Change-Id: Ic326229120ffc5d839bbf465855d8be857ab4f73
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7377
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Maciej Wawryk <maciejx.wawryk@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Change-Id: I7e739a4e085d150b0be73cd890f0cf85f05ab7fd
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7200
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Migration can take longer than 10s, hence we need to give fio more
time to spin in order to make sure it's still running on the target
vm after migration is complete.
On the other hand, reduce the timeout used to wait for fio after
the migration is done - there's no need to wait almost a minute,
half that time.
Signed-off-by: Michal Berger <michalx.berger@intel.com>
Change-Id: I1b53682d5c8bc72336a9eead28c395f97cd81fe7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7199
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
We only need SPDK_CU_ASSERT_FATAL to check for
NULL pointers. Other checks should just use
CU_ASSERT and variants.
There are some nvme_ns_cmd_ut checks that are
using SPDK_CU_ASSERT_FATAL unnecessarily. Let's fix
them.
Found during investigation of issue #1882.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I0b313e44e2ed05554783933e7d4bbc5f07a7e84a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7290
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This include isn't needed in queue_extras.h itself.
There were a few places that were implicitly
depending on this include, so fix those to include
util.h explicitly.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ia962ae5a4403ee8ae15f3106d0d5e7d7412a4535
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7172
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Check if qpair has a poll group during the connect process,
use poll group's statistics or allocate own structure per
qpair. That is done due to not all applications use poll
groups and we want to avoid "if (qpair->group)"
conditions in data path.
Admin qpair always allocates its own statistics
structure but the statistics are not reported
since this qpair is not attached to a poll group.
Statistics are reported by spdk_nvme_perf tool
if --transport-stats and in bdev_nvme_transport_statistics
RPC method.
Change-Id: I58765be161491fe394968ea65ea22db1478b219a
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6304
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
These are interface functions that can be used by
an application e.g. spdk_nvme_perf or bdev_nvme
library. The next patches will add usage of these
functions.
Change-Id: I33b88e0e713c2ea5967f9241885e3257c5070577
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6300
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
