When iovs are copied from bounce or to bounce, the bounce is usually
alloced from data_buf_pool for better performance, and is multi iovs
instead of a single buffer. Therefore, block-aligned bounce are
supported.
Signed-off-by: Chunsong Feng <fengchunsong@huawei.com>
Change-Id: If56b21d9e46c73d4c956c227bec33ddd0ab9745b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11860
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
spdk_sock_map_insert() allows for allocating a sock_map
entry, without assigning any sock_group.
This is useful for cases where placement_id determined
by the component using spdk_sock_map_*. See PLACEMENT_MARK mode.
Placement_id's are allocated first, then an empty one is found
using spdk_sock_map_find_free().
Since the above is a valid use case, then entry in sock_map
can exist without a group assigned. spdk_sock_map_lookup() has
to handle such cases, rather than trigger an assert.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Ia717c38fef5e71fe44471ea12f61a5548463f0cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10725
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: wanghailiang <hailiangx.e.wang@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
The usage of internal API for sock_map was not unit tested,
so far.
This patch adds first set of UT for the sock_map,
expanding it and fixing some issues later in the series.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Idfce8e19668a87f1d45d73310edb17d71d9f8bd8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10724
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
As we now only support a single WQ, there's no need for a teble of
them and no need to assert that the stride from WQ to WQ is the
same as the WQ struct size.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I205f36aae22070f532653726dd75249bbafbe3ef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/12081
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
First in a series of patches that will enable multiple engines
to exist at once and choose the best one based on their priorities
and capabilites, the public API will no longer be needed.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ia87b83aa2263745a94a822a160b6e97bb2e0dc19
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11948
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
With recent changes libreduce should provide correct buffers
if the driver doesn't support SGL in/out. This patch verifies
that we don't use SGLs when they are not supported.
Since even a single buffer can be split on 2MB page
boundary, it is not enough just to check iovs count.
Added asserts that the first elements of mbufs are
not null to avoid scan build errors
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I620e43bf5b1abd25cab412fe08346a6d767c9be9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11973
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
rte_pktmbuf_free frees the given mbuf and any chained mbufs.
It can cause double free of some mbuf if we free every mbuf
in a loop. Instead use rte_pktmbuf_free_bulk which correctly release
chained mbufs.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I55fd7832ff656f519a4ed2f02de8ef1a0f637a02
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11972
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
In the compression operation we may have SGL input
if user's buffer is fragmented or less than chunk_size.
If the backing device doesn't support SGL input then
we should copy user's buffers into decomp_buffer
(including paddings if any).
In the decompression operation, if the backing device
doesn't support SGL output, we use a single output buffer
which is pointing to decomp_buffer. Once the operation
completes, we should copy the result into user's buffers.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: Ic7fddd38374bb6898256633eacd192dbaf36541a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11970
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The driver always creates a single group containing all of the engines
and a single work queue.
Change-Id: I83f170f966abbd141304c49bd75ffe4608f5ad03
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11533
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
It is not used for anything.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I1d967b2d0e404756f7ceda98ddc4ee9017ec83f7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11489
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
It turns out that this can stay on the stack.
Change-Id: I961366307dae5ec7413a86271cd1dfb370b8f9f3
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11488
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
These aren't ever accessed in the main I/O path, so we can read them in
whenever we need them and make the code a lot simpler.
Change-Id: Icfdbfe9f2d9db13f4d0d28b2b4103cd0c443bcf4
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11485
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This is no longer needed.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I08c788ca0451e739804b568d613c1e52e071c61f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11794
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Fill is sent in as a uint8, we need to populate the full uint64
input with the uint8 pattern or we'll get a miscompare. This is
how idxd was doing it, instead of adding the same code to ioat just
move it up a layer.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ia4aab1c6230f35ab88bb8a0e3b8e16dbd93007c7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11947
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
- Fixed duplication of key, key2, drv_name, cipher, etc., fields in
struct bdev_names and struct vbdev_crypto. Moved all of them into
the new struct vbdev_crypto_opts, which is re-used by both structs.
This aslo removes duplication in error handling and fininalization
logic that checks the keys are zeroed out and properly freed.
- Moved unhexlify into vbdev rpc code. All keys passed to vbdev
already in the binary form.
- Provide meaningful error messages in the rpc response on keys
validation issues during setup of crypto vbdev.
- Updated unit tests.
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: I1fab8771bbbc0cd2f359f0d105fec28fb86893b3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11631
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
That is done to correctly handle metadata pointer which is part
of ext_opts structure. It will also be used by the next patch to
remove memory_domain pointer if request which uses local buffers
is split
Force the user to set correct ext_opts size, update API functions
description.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I77517d70df34a998d718cc6474fb4c538a42918f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11349
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Bdev modules must not access internal bdev_io
structure, so add a new pointer in a public
section. Pointer in internal section will be
used in next patch
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: Ib631563015b3e5fa9300d22b7ae59d8db43c8275
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10421
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch is a preparation for enabling of memory domains
pull/psuh functionality. Since memory domains API is
asynchronous, this patch makes asynchronous operations
with bounce buffers.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: Ieb1f2a0c151149af58cfd7607dbde4c76c3c288d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10420
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
SPDK has settled on what the optimal DSA configuration is, so let's
always use it.
Change-Id: I24b9b717709d553789285198b1aa391f4d7f0445
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11532
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
The names on these were changed.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ib75a60342c08f72dad39635a9244421c1cca5485
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11793
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add a new flag is_disconnecting to struct spdk_nvme_ctrlr.
Separate calling nvme_ctrlr_disconnect() and nvme_ctrlr_disconnect_done()
by using the flag is_disconnecting.
Additionally, change nvme_ctrlr_fail() to skip setting ctrlr->is_failed
to true if ctrlr->is_disconnecting is true.
Change-Id: Ie2c74ba41f120662a30f6198751d07005d23abcf
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11000
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is a preparation to make nvme_transport_ctrlr_disconnect_qpair()
asynchronous.
For nvme_transport_ctrlr_disconnect_qpair(), factor out operations after
returning from transport's specific ctrlr_disconnect_qpair() into a helper
function nvme_transport_ctrlr_disconnect_qpair_done().
Then move nvme_transport_ctrlr_disconnect_qpair_done() into the end of
the transport specific ctrlr_disconnect_qpair().
Additionally remove the operation to overwrite the qpair state to
DISCONNECTED from nvme_transport_connect_qpair_fail() because
this is duplicated and nvme_transport_ctrlr_disconnect_qpair() is responsible
to make the qpair disconnected even after it completes asynchronously.
Change-Id: I9c8faa7039d306d3e31a8f51826755ce8840a8aa
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10851
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
For RDMA transport, adminq will find transport error first because
usually only adminq polls CM events.
Change-Id: I7b22cc8883bf02198f1a90d2654c1de6f2e736e6
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11331
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
If qpair is disconnected asynchronously, it takes time from detecting
transport error to actually disconnected. We should avoid using the
path as soon as possible after detecting any transport error.
Poll group clears I/O path cache if it finds transport error and avoid
using the path which had transport error.
These changes will reduce the failover time.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I00580159a84372a115ed5e62a6ce13eed4368999
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11329
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
spdk_nvme_ctrlr_disconnect() will be made asynchronous in the
following patches and so we will need to have some changes.
spdk_nvme_ctrlr_disconnect() disconnects adminq and ctrlr synchronously
now.
If spdk_nvme_ctrlr_disconnect() is made asynchronous,
spdk_nvme_ctrlr_process_admin_completions() will complete to disconnect
adminq and ctrlr, and will return -ENXIO only if adminq is disconnected.
However even now spdk_nvme_ctrlr_process_admin_completions() returns
-ENXIO if adminq is disconnected.
So as a preparation, set a callback before calling spdk_nvme_ctrlr_disconnect()
and call the callback if it is set and spdk_nvme_ctrlr_process_admin_completions()
returns -ENXIO.
Besides, fix the return value of bdev_nvme_poll_adminq() in this patch.
Change-Id: I2559f86bb8cf9a92b5b386ed816c00b08c9832df
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10950
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
As we do when deleting ctrlr_channel, disconnect and then free I/O
qpair in a ctrlr reset sequence.
Deleting ctrlr_channel and resetting ctrlr_channel may cause conflicts.
This patch processes such conflicts correctly.
If destroy_ctrlr_channel_cb() is executed between pending and executing
reset_destroy_qpair(), reset_destroy_qpair() is not executed because
ctrlr_channel is not found. In this case, destroy_qpair_channel()
starts disconnecting qpair and deletes ctrlr_channel. Then
disconnected_qpair_cb() releases a reference to poll group.
If destroy_ctrlr_channel_cb() is excuted between executing reset_destroy_qpair()
and disconnected_qpair_cb(), destroy_ctrlr_channel_cb() skips
ctrlr_channel for a reset sequence.
Change-Id: I1f49f74b94aefbea178680aa53ded3a12876c676
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10766
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
At the moment MLX5 uses different number of qp descriptors than the
other pmd crypto drivers. Adding it to vbdev_crypto on init and re-use
everywhere we need it.
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: Iea4d4787fc5fd91f27c4a70cf78c5660f09bc854
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11878
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Since IV length is the same for all pmd crypto drivers,
AES_CBC_IV_LENGTH is renamed to IV_LENGTH.
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: If8769db119eb599a17c267e8950f18f5a0ea995b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11875
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
spdk_nvme_poll_group has followed spdk_nvme_qpair about how to
process I/O qpair deletion inside of a completion context.
spdk_nvme_qpair_process_completions() accesses qpair after
returning from nvme_transport_qpair_process_completions().
So this is reasonable.
On the other hand, if spdk_nvme_poll_group_process_completions()
can execute spdk_nvme_ctrlr_free_io_qpair() inside of a completion
context, the target qpair is ensured to be deleted after returning
from spdk_nvme_ctrlr_free_io_qpair(). Then the target qpair is
not accessed anymore in spdk_nvme_poll_group_process_completions().
Remove two variables, in_completion_context and num_qpairs_to_delete,
of spdk_nvme_transport_poll_group and the related code.
This change is really necessary to support the following case.
In the NVMe bdev module, a nvme_qpair has a qpair and a poll_group
channel. disconnected_qpair_cb calls spdk_nvme_ctrlr_free_io_qpair()
for the qpair and spdk_put_io_channel() to the poll_group_channel.
spdk_nvme_ctrlr_free_io_qpair() is executed after unwinding stack
but spdk_put_io_channel() is executed now. The callback to
spdk_put_io_channel() calls spdk_nvme_poll_group_destroy(). However,
spdk_nvme_ctrlr_free_io_qpair() is not executed. Hence
spdk_nvme_poll_group_destroy() fails.
Update the corresponding stub in unit test together.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: Icd1f1daf049c6c7ffb28790fe87989a1060f8952
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11496
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is another preparation to disconnect qpair asynchronously.
Add nvme_qpair object and move the qpair and poll_group pointers and
the io_path_list list from nvme_ctrlr_channel to nvme_qpair. nvme_qpair
is allocated dynamically when creating nvme_ctrlr_channel, and
nvme_ctrlr_channel points to nvme_qpair.
We want to keep the times of references at I/O path. Change nvme_io_path
to point nvme_qpair instead of nvme_ctrlr_channel, and add
nvme_ctrlr_channel pointer to nvme_qpair.
nvme_ctrlr_channel may be freed earlier than nvme_qpair. nvme_poll_group
lists nvme_qpair instead of nvme_ctrlr_channel and nvme_qpair has a
pointer to nvme_ctrlr.
By using the nvme_ctrlr pointer of the nvme_qpair, a helper function
nvme_ctrlr_channel_get_ctrlr() is not necessary any more. Remove it.
Change-Id: Ib3f579d3441f31b9db7d3844ec56c49e2bb53a5d
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11832
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
In the following patches, spdk_nvme_ctrlr_disconnect_io_qpair() will
be changed to be asynchronous, spdk_nvme_ctrlr_disconnect_io_qpair()
will be called first and then spdk_nvme_ctrlr_free_io_qpair() after
the qpair is actually disconnected.
We will not be able to keep the current bdev_nvme_destroy_qpair()
function.
As a preparation, inline bdev_nvme_destroy_qpair() and remove it.
Additionally, this patch has the following changes.
Previously I/O qpair was freed and then I/O path caches were cleared.
Both are SPDK thread local. So there is no dependency for the ordering
of these two operations. However, it will reduce the size of the
following patches if we clear I/O path caches before freeing I/O qpair
when the qpair is disconnected. Hence we clear I/O path caches and then
free I/O qpair.
Remove DTRACE for bdev_nvme_destroy_qpair() for now.
It will be restored in the following patches.
Furthermore, fix potential NULL pointer acces in
bdev_nvme_create_qpair().
Change-Id: I0ab78ccb0d240e56b95b53179341afcd909a31f6
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10746
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
In test_nvme_free_request, there is valgrind error:
Conditional jump or move depends on uninitialised value(s)
Signed-off-by: Rui Chang <rui.chang@arm.com>
Change-Id: I80f741cac9316d86b060419e3b6fb651fa018aa4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11826
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
If 0 - UINT32_MAX or UINT32_MAX - 0 is substituted into a int variable,
we cannot get any expected result.
Fix the bug and add unit test case to verify the fix.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: Iad2ea681ad8ad234e70c7310b58785a999612156
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11837
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
The following patches will enable us to specify I/O error resiliency
options per nvme_ctrlr as global options. To do it easier, move
per controller options about I/O error resiliency into struct nvme_ctrlr_opts.
prchk_flags is not exactly for resiliency but move it into struct
nvme_ctrlr_opts too.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I85fd1738bb6e293cd804b086ade82274485f213d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11829
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
If 0 - UINT32_MAX or UINT32_MAX - 0 is substituted into a int variable,
we cannot get any expected result.
Fix the bug and add unit test case to verify the fix.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: Ib045273238753e16755328805b38569909c8b83a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11836
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
The spdk_msg_mempool structure has a fixed size, which is not flexible
enough. The size of the memory allocation can now be changed in the
options given to the spdk_app_start function.
Signed-off-by: Alexis Lescouet <alexis.lescouet@nutanix.com>
Change-Id: I1d6524ab8cf23f69f553aedb0f5b0cdc9dde374b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11635
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
We will use nvmf library CSTS.CFS instead so that the client can
get this error status.
Change-Id: I42c248a7333d1f9c940bb29135c887a61c906bd4
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11676
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Thanos Makatos <thanos.makatos@nutanix.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Plumbing for flags was added in prior pathces. This patch
introduces and respects the relevant flags for use with PMEM
aka durable memory through the accel_fw, IDXD, IOAT and SW
modules.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I792f31459e061d220965feced60e0c236d819a68
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9455
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch is just plumbing the flags param. Use of it for PMEM
will come in upcoming patches.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I620df072aaad3f8062a0312bbea3da1bc3f911b9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9281
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: GangCao <gang.cao@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
- Continue init of the other crypto devices (mlx5) after failure of
rte_vdev_init(AESNI_MB) in vbdev_crypto_init_crypto_drivers(). It
simply may not be enabled in DPDK because it requires IPSec_MB>=1.0
installed in the system. Reproduces with --with-dpdk=dpdk/install
option used, when the target DPDK is built without control of IPSec
version from the SPDK side.
- Updated crypto_ut to test the new behavior of error handling from
rte_vdev_init(AESNI_MB) in vbdev_crypto_init_crypto_drivers().
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: Icd4db8877afe87db8166c40d6e7b414cd43c9c25
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11624
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
- Switched to using rte_mempool for mbufs instead of spdk_mempool. This
allows using rte pkt_mbuf API that properly handles mbuf fields we need
for mlx5 and we don't have to do it manually when sending crypto ops.
- Using rte_mempool *g_mbuf_mp in vbdev crypto ut and added the mocking
API code.
- crypto_ut update to follow pkt_mbuf API rules.
Signed-off-by: Yuriy Umanets <yumanets@nvidia.com>
Change-Id: Ia5576c672ac2eebb260bfdbb528ddb9edcd8f036
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11623
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This reverts commit 3bacd6653d.
Change-Id: I8dbaffc9f50cf9627720667644496cdaf4e81c3f
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11723
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
According to NVMe over Fabrics spec number of SGLs supported by the
controller is reported in MSDBD. But it is also implicitly limited by
command capsule size (IOCCSZ) since SGL are passed in capsule.
This patch adjusts max_sges to capsule size if required. Adjustment to
MSDBD is also moved to transport layer because it is fabrics specific
parameter and is not valid for PCIe transport.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: I44918eb949345c61242ca50a524d21d04b6ac058
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11669
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For the benefit of forthcoming vfio-user changes, register the poll
group poller prior to calling the transport create callback, and pass in
a pointer to the poll group itself.
Signed-off-by: John Levon <john.levon@nutanix.com>
Change-Id: Idbc24126c9d46f8162e4ded07c5a0ecf074fc7dd
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10718
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
With async connect, we need to avoid the case
where the initiator is sending the icreq, and
meanwhile the application submits enough I/O
such that the request objects are exhausted, leaving
none for the FABRICS/CONNECT command that we need
to send after the icreq is done.
So allocate an extra request, and then use it
when sending the FABRICS/CONNECT command, rather
than trying to pull one from the qpair's STAILQ.
Fixes issue #2371.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: If42a3fbb3fd9d863ee48cf5cae75a9ba1754c349
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11515
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This has changed to control the number of read buffers allocated to the
group, but it is only valid to set this register if the device has
indicated it supports it. Further, the default value is what we want
anyway, so we can skip setting it altogether.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ic54672ea6cb16acc7613860e36d9f7033048bd98
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11484
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
All of the other structs and unions spell out register, so match the
style.
Change-Id: Ie502e80206305037d1518a1db590d89b7479abb4
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11433
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
SPDK can submit more commands to remote NVMf target than allowed by
negotiated queue size. SPDK submits up to SQSIZE commands, but only
SQSIZE-1 are allowed.
Here is a relevant quote from NVMe over Fabrics rev.1.1a ch.2.4.1
“Submission Queue Flow Control Negotiation”:
If SQ flow control is disabled, then the host should limit the number
of outstanding commands for a queue pair to be less than the size of
the Submission Queue. If the controller detects that the number of
outstanding commands for a queue pair is greater than or equal to the
size of the Submission Queue, then the controller shall:
a) stop processing commands and set the Controller Fatal
Status (CSTS.CFS) bit to ‘1’ (refer to section 10.5 in the NVMe Base
specification); and
b) terminate the NVMe Transport connection and end the association
between the host and the controller.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: Ifbcf5d51911fc4ddcea1f7cde3135571648606f3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11413
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
According to NVMe over Fabrics specification (rev.1.1a) HSQSIZE sent
in RDMA_CM_REQUEST private data (ch.7.3.6.4) shall be the same as
SQSIZE later sent in Connect command (ch.3.3).
SPDK NVMe RDMA initiator adjusts SQSIZE to CRQSIZE received from
target in RDMA_CM_ACCEPT private data. Target is allowed to send
CRQSIZE < HSQSIZE if RNR retries are used. So, it is possible that
SQSIZE sent by SPDK will be lower than previously sent HSQSIZE. There
are targets validating this match and they reject connection from
SPDK.
Linux kernel NVMe initiator doesn't perform such adjustments and
connects well to such targets.
This patch aligns SPDK behavior with specification and Linux kernel
implementation.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: I01968d1c07d284396fa5939932d85841351d7a45
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11350
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
There are errors occur that uninitialised value created by a stack allocation when running unittest_accel and unittest_nvme_rdma with valgrind.
Change-Id: I4b48b472cc7c189cbcaf8ca772830a23118e7e17
Signed-off-by: Jaylyn Ren <jaylyn.ren@arm.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10559
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
it shall be executed on ctrlr's thread not subsystem's
Signed-off-by: Jacek Kalwas <jacek.kalwas@intel.com>
Change-Id: I58c60525191085d3d6a583862ba5d71ea90940c7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11105
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
In many cases, addressing bdevs by their UUIDs is often easier than
using their names, which can be somewhat arbitrary. For instance, the
NVMe bdev builds a name by addng the n{NSID} suffix to the controller's
name, while the UUID is filled with NGUID (if available).
The UUID alias is stored in the form defined by RFC 4122, meaning five
groups of lower-case hexadecimal characters. It's important to note
that bdev layer uses case-sensitive name comparison, so the user needs
to use the same textual UUID representation.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I8b112fb81f29e952459d5f81d97fdc7a591730f8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11395
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
bdev_multi_allocation tries to write four characters, an integer between
0 and INT_MAX, and a nul byte into 10 characters. That requires at least
15 characters.
This leads to build failures with "make CONFIG_DEBUG=n CONFIG_UBSAN=y".
Change-Id: I8cb9fd4ede31ae24809e4a04fd60a67dae3a0ac4
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11261
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
An spdk_bs_opts structure is sometimes partially initialized due to
using sizeof(opts) (struct spdk_blob_opts, 64 bytes) rather than
sizeof(bs_opts) (struct spdk_bs_opts, 72 bytes).
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Change-Id: Iaaa89bb419f66969d0888f49f8991c35b3dc5ea4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11268
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
While not documented as such, spdk_bdev_module_claim_bdev() has always
allowed a bdev that is opened read-only to remain read-only when
claimed. This occurs when NULL is passed in place of an spdk_bdev_desc.
This change updates the function's documentation to match the
implementation and adds a unit test to ensure the current behavior
remains.
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Change-Id: Ief26de60e4408bfe1aa60b7a4e1d8adf273470b6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11267
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
When an unexpected xattr name is passed to lvol_get_xattr_value(), no
error is returned to the caller. The one caller, blob_set_xattrs() via
the xattrs->get_value callback, makes the reasonable assumption that a
lookup that fails to find a value returns a NULL value. This updates
lvol_get_xattr_value() to match that expectation.
Signed-off-by: Mike Gerdts <mgerdts@nvidia.com>
Change-Id: I5c7a740f2757e6d8265ba2637afecb729acfcdd4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11326
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
VFIO in QEMU uses region 9 as the PCI passthrough devices' migration channel.
The format of the region 9 migration region is as follows:
------------------------------------------------------------------
|vfio_device_migration_info| data section |
------------------------------------------------------------------
QEMU will access vfio_device_migration_info to controll the migration
process.
For SPDK vfio-user target, we also implement the BAR9 via libvfio-user,
and we also define the NVMe device specific migration data stored in
data section of BAR9. QEMU doesn't care about the format in data section,
it will help us to gather the NVMe specific migration data in source VM and
then restore the migration date to data section of BAR9 in destination VM.
The core idea to implement live migration will following the device state
change which is controlled by QEMU. First QEMU will try to STOP the device
in the source VM, and set the destination VM to RESUME state, SPDK will save
NVMe devic state data structure to BAR9 in the source VM once the subsystem
is paused, then QEMU will read BAR9 in source VM and restore the content of
BAR9 in destination VM, finally in the destination VM, we will restore the
NVMe device state include BARs/PCI CFG/queue pairs in the destination VM.
Change-Id: I42e38f28c3ff59831be63290038b50d199d06658
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7617
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Thanos Makatos <thanos.makatos@nutanix.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch aligns namespace comparison with Linux kernel
implementation:
- UUID is optional and may be NULL
- command set (CSI) should be the same
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: I8f889989f24cd51b104057217f87eb303b30fa68
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11312
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
For correct behaviour, pthread_mutex must be initialized before use
and destroyed afterwards. An already initialized mutex should not
be re-initialized.
Add calls to nvme_ctrlr_construct where nvme_ctrlr_destruct is
called without a matching construct.
Add missing calls to mutex_init and mutex_destroy as required.
Signed-off-by: Nick Connolly <nick.connolly@mayadata.io>
Change-Id: I9753fa7fbd77402f23a08a66f4b489a5c229487a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11298
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Community-CI: Mellanox Build Bot
This reverts commit eb09178a59.
Reason for revert:
This caused a degradation for adminq.
For adminq, ctrlr_delete_io_qpair() is not called until ctrlr is destructed.
So necessary delete operations are not done for adminq.
Reverting the patch is practical for now.
Change-Id: Ib55ff81dfe97ee1e2c83876912e851c61f20e354
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10878
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Found via inspection during spec review of latest HW. We were using the
wrong stride for the WQCFG regsiter when configuring but it just so
happened to be the right value for the current DSA version. We were
mixing up the size of the WQCFG register with the stride value used to
configure the next WQCFG regsiter as they are not contiguous in HW, we
need to read another capabilities bit to determine the address of the
next wqcfg to configure..
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I14d1ff95e0131fd30121aa955bfbc8c8fb3fc512
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10968
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Compliant with both current and next gen DSA.
Note: some fields in gencap were mapped incorrectly
previously, but this did not impact the SPDK driver
because the only times those values (max_xfer_shift
and max_batch_shift) were used were in asserts.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I9648184670f661166136e7898d0d8c7e07d8c746
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10966
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Creation of sockets is specific to rte_vhost, so it
functionality responsible for setting path for them.
dev_dirname is renamed to g_vhost_user_dev_dirname
and its definition is moved to rte_vhost_user.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I9bae67667b0f6624f2daf3244a048d10e94e553c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10631
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
vhost.c contains a lot of functionality that
is rte_vhost specific. This series is moving
rte_vhost specific functionality to rte_vhost_user.c.
UT for vhost didn't make a distinction for either.
So starting with this patch the rte_vhost_user.c
is now included in the UT, only stubing out rte_vhost functions.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I0d5f62ad47d1261bbb44c0aa23400d94ece4564e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10743
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
From SAM-4, section 5.13 (Sense Data);
“When a command terminates with a CHECK CONDITION status, sense data shall be returned
in the same I_T_L_Q nexus transaction (see 3.1.50) as the CHECK CONDITION status. After
the sense data is returned, it shall be cleared except when it is associated with a unit
attention condition and the UA_INTLCK_CTRL field in the Control mode page (see SPC-4)
contains 10b or 11b.”
SPDK does not set UA_INTLCK_CTRL to 10b or 11b, so we set the unit attention condition
immediately against a single IO or Admin IO after reporting it via a CHECK CONDITION.
Once the failed IO received at iSCSI initiator side, it will be retried. In the case of
resize operation, if there is no IO from iSCSI initiator side, the unit attention
condition will be delayed to report until the first IO is received at the iSCSI target
side.
Meanwhile, we clear the resizing (newly added) flag on our SCSI LUN structure after
first time we report the resize unit attention condition.
The kernel initiator won’t actually resize the corresponding block device automatically.
It will report a uevent, and then you can set up udev rules to trigger a rescan. SPDK
iSCSI initiator will automatically report the LUN size change.
Change-Id: Ifc85b8d4d3fbea13e76fb5d1faf1ac6c8f662e6c
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11086
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Increase the batch size and with it the effective queue depth per
channel to 512.
Change-Id: Ide665e92d47ee753c141f34dd6a8bc4d040fe8db
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11031
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: John Kariuki <John.K.Kariuki@intel.com>
libvfio-user will call quiesce callback when there are
memory region add/remove and device state change requests
from client, and in the quiesce callback, we will pause
the subsystem so that it's safe to do everything after
it, then after quiesce callback, we will resume the
subsystem. The quiesce callback is also used in
live migration, each device state change will quiesce
the device first.
Change-Id: I3a6a0320ad76c6b2d1d65c754b9f79cce5c9c683
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10620
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Admin commands can be sent and polled from any thread, which also means
that the error injection queue on the admin qpair can be accessed from
multiple threads. Therefore, any modifications to that queue should be
done under the ctrlr lock.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: Ib1ed194405cb5b93f65a007b9749fd4433dc367d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11099
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michael Haeuptle <michaelhaeuptle@gmail.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
There is an error case that the block device didn't complete
outstanding IOs during the controller reset or shutdown, so
the NVMf library will wait until all the IOs returned from
the backend, however, so here we added a timeout timer, when
the time expired, we will try to reset the block device which
hold the outstanding IOs.
Fix#2194.
Change-Id: I8d0746335e1f20a09e6a9ea87730551808a898d1
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9909
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Fix warning: missing braces around initializer
This issue is seen with gcc (GCC) 4.8.5 20150623.
Warning like below:
nvme_tcp_ut.c:243:9: warning: (near initialization for ‘ctrlr.ns’) [-Wmissing-braces]
nvme_tcp_ut.c: In function ‘test_nvme_tcp_req_init’:
nvme_tcp_ut.c:525:9: warning: missing braces around initializer [-Wmissing-braces]
struct spdk_nvme_ctrlr ctrlr = {0};
^
nvme_tcp_ut.c:525:9: warning: (near initialization for ‘ctrlr.ns’) [-Wmissing-braces]
And more information from below link:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=53119
Change-Id: I88b5b3908d5d0daa9383e47a1ed53288f342ca3b
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11137
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
This is the same effort as the last patch.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I94ef08abdbb2bd2e07d0cd1e552c5d05c805233e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10817
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
More precise stubs for spdk_nvme_poll_group are critically important
to verify upcoming changes.
Add a flag is_failed to struct spdk_nvme_qpair separately from
is_connected. This is used to inject error to a connection.
Replace a single list qpairs by two lists, connected_qpairs and
disconnected_qpairs for struct spdk_nvme_poll_group.
Then utilize these to manage qpair in poll group.
spdk_nvme_ctrlr_reconnect_io_qpair() is not used in the NVMe bdev
module now. Remove the corresponding stub.
Adjust polling count accordingly.
Change-Id: I4d867c56ae518276813f6f96d23a5f6933364fd4
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10816
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
nvme_poll_group_disconnect_qpair() is called only by a single place now.
We do not need the flag poll_group_disconnect_in_progress any more.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I8f9c0f14baa8fcb9b0637635a5bb3d34a8b11af5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10673
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
nvme_ctrlr_disconnect_qpair() calls nvme_poll_group_disconnect_qpair() if the qpair
uses a poll group, and nvme_poll_group_disconnect_qpair() calls
nvme_ctrlr_disconnect_qpair() if the state of the qpair is not DISCONNECTING.
This relationship made the code very complex.
A few patches starting from this patch simplifies disconnect and free qpair
operations.
This patch swaps the ordering of nvme_ctrlr_disconnect_qpair() and
spdk_nvme_poll_group_remove() in spdk_nvme_ctrlr_free_io_qpair().
This ensures the qpair is disconnected when spdk_nvme_ctrlr_free_io_qpair()
calls spdk_nvme_poll_group_remove().
This enables us to limit spdk_nvme_poll_group_remove() to be available
only for disconnected qpairs.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I0601a74f953a2efc4f177a51a4450baea33533d4
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10670
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
If ctrlr_loss_timeout_sec is set to -1, reconnect is tried repeatedly
indefinitely, and I/Os continue to be queued.
This patch adds another option fast_io_fail_timeout_sec, a flag
fast_io_fail_timedout to nvme_ctrlr.
If the time fast_io_fail_timeout_sec passed after starting reset,
set fast_io_fail_timedout to true not to use the path for I/O submission.
fast_io_fail_timeout_sec is initialized to zero as same as
ctrlr_loss_timeout_sec and reconnect_delay_sec.
The name of the parameter follows the famous DM-multipath, its fast_io_fail_tmo.
Change-Id: Ib870cf8e2fd29300c47f1df69617776f4e67bd8c
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10301
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previously reconnect retry was not controlled and was repeated indefinitely.
This patch adds two options, ctrlr_loss_timeout_sec and reconnect_delay_sec,
to nvme_ctrlr and add reset_start_tsc, reconnect_is_delayed, and
reconnect_delay_timer to nvme_ctrlr to control reconnect retry.
Both of ctrlr_loss_timeout_sec and reconnect_delay_sec are initialized to
zero. This means reconnect is not throttled as we did before this patch.
A few more changes are added.
Change nvme_io_path_is_failed() to return false if reset is throttled
even if nvme_ctrlr is reseting or is to be reconnected.
spdk_nvme_ctrlr_reconnect_poll_async() may continue returning -EAGAIN
infinitely. To check out such exceptional case, use ctrlr_loss_timeout_sec.
Not only ctrlr reset but also non-multipath ctrlr failover is controlled.
So we need to include path failover into ctrlr reconnect.
When the active path is removed and switched to one of the alternative paths,
if ctrlr reconnect is scheduled, connecting to the alternative path is left
to the scheduled reconnect.
If reset or reconnect ctrlr is failed and the retry is scheduled,
switch the active path to one of alternative paths.
Restore unit test cases removed in the previous patches.
Change-Id: Idec636c4eced39eb47ff4ef6fde72d6fd9fe4f85
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10128
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
We noticed the difference between the SPDK 21.10 and the latest master
in a test.
The simplified scenario is as follows:
1. Start SPDK NVMe-oF target
2. Run bdevperf for the target with -f parameter to suppress exit
on failure.
3. Kill the target after I/O started.
With the SPDK 21.10, bdevperf retries failed I/Os and exits after
the test time is over.
With the latest SPDK master, bdevperf hungs and does not exit even
after the test time is over.
The cause was as follows:
reset ctrlr is repeated very quickly (once per 10ms by default) and hence
I/Os were queued infinitely because nvme_io_path_is_failed() returned
false if nvme_ctrlr is resetting.
We should queue I/O when nvme_ctrlr is resetting only if reset is throttoled
and fail-fast for the repeated failures is supported.
Hence in this patch, fix the degradation and remove the related unit
test cases.
Reported-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I4047d42dc44488a05264c6a841d101a7c371358b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11062
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Adding metadata support for io commands. Currently metadata is ignored
even if present in the cmd struct. Making metadata adress
readable/writable depending on data transfer bits. Adding extra unit
test to make sure metadata fields are populated.
Signed-off-by: Ahriben Gonzalez <ahribeng@gmail.com>
Change-Id: I1d01974a6b2831c82b43e94073065d235eea429a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10854
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
We only populate active namespaces into the main namespace tree, so we
don't need a separate list of active namespaces too.
Change-Id: Iaf194f806cc1d9672f5567cff3dffafff3165069
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10034
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Since this is now sparsely populated, a tree is a better choice.
Change-Id: Ie66d913fa1d298de56a7d22ef55f0adf7f8803b8
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10031
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Some subsystems report a very large maximum value for the number of
namespaces, but in essentially every case the subsystem is sparsely
populated with active namespaces. To save memory, don't allocate
objects for the inactive ones.
Change-Id: I4cbeb5a7a898d3c685f4a3a9ec4c2ce45efffb92
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9898
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Chaining may be faster, but this is really an implementation detail of
the idxd driver. Push the decision on how to implement a vectored crc
down into the individual drivers and eliminate it from the generic
framework.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Iedbdc5a6dbd3f7d1674d0a83f6827588f4b6b2fb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10291
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Zero-copy requests are kept on the outstanding queue for the whole
duration of the request - from the initial zcopy_start submission to the
completion of zcopy_end. This means, that there's a period in which a
request doesn't wait for a completion from the bdev layer, but is still
on the oustanding queue (after zcopy_start callback, before zcopy_end
submit). If a qpair gets disconnected while a request is in this state,
we need to manually force its completion, as otherwise it might hang
indefinitely (e.g. waiting for host data).
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I53731b8e363b725efa564ca3c7d89b46f5fb2a24
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10793
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
The zero-copy requests can also be queued when a subsystem is paused, so
we need to properly resume and submit them by using zcopy_start.
Since only requests that haven't received the zero-copy buffer (i.e.
before zcopy_start was called) can be queued, we don't need to bother
with checking zcopy_phase.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: Ie629688f6961eb2ae05741df496720b91be4d80d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10792
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
We sort secondary trids to avoid using disconnected trids for failover.
However the sort had a bug.
This bug was found by running test/nvmf/host/multipath.sh in a loop.
Verify the fix by adding unit test.
Fixes#2300
Signed-off-by: Shuhei Matsumoto <shuheimatsumoto@gmail.com>
Change-Id: I22b0ede4d2ef98b786c3e0d1f5337a2d568ba56d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10921
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This patch adds the framework for a discovery
service in the bdev/nvme module.
Users can specify an IP/port of a discovery service.
The bdev/nvme module will connect to a discovery
controller, get the discovery log page, and then
register for AERs. It will connect to each
subsystem specified in the initial log page.
AER completions will trigger fetching the log
page again, at which point new subsystems will
be connected to, or removed subsystems will be
detached.
This patch does the following:
* Adds the new start_discovery RPC
* Connects to the discovery controller
* Gets the discovery log page
* Registers for AERs
* Detach from discovery controllers at shutdown
Subsequent patches in this series will:
* Connect to subsystems listed in discovery log page
* Detach from subsystems that were listed in earlier
discovery log pages but subsequently removed
* Add a stop_discovery RPC
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I54bfa896a48c5619676f156b5ea9f2d1f886c72f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10694
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Since spdk_bdev_zcopy_end() cannot really fail (it only fails if we pass
a bad bdev_io), we can simplify the nvmf zcopy_end functions by making
them void and always expect asynchronous completion.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I6e88ac28aba13acadea88489ac0dd20d1f52f999
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10790
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Since this path now supports sending zero-copy, use it for zcopy_start.
Additionally, it makes it possible make zcopy_start void, as it reports all errors
asynchronously via request_complete(), and remove some of the duplicated
error checks.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I41f43ce1651432d9a7d74e3680d4a3f780128a1d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10789
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Additionally, the NVMe completion status is now updated and the IOs are
queued if the bdev layer doesn't have enough IO descriptors. It makes
the zcopy operations behave similarly to the other IO operations.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I455ae781e32aa6e60d144d2c91f109bd8be46664
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10787
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
