spdk_sock_close() may not complete synchronously.
Then the following scenario is possible.
ctrlr_disconnected_qpair() calls spdk_sock_close(). Then any request may
complete and call _pdu_write_done(). qpair is still associated with a
poll_group and is inserted into the group->needs_poll list.
After ctrlr_disconnected_qpair() completes, disconnected_qpair_cb() is
called. disconnected_qpair_cb() calls spdk_nvme_ctrlr_free_io_qpair().
spdk_nvme_ctrlr_free_io_qpair() calls spdk_nvme_poll_group_remove().
spdk_nvme_poll_group() removes qpair only from the
group->disconnected_qpairs list.
Even after qpair->poll_group is nullified, qpair is still in the
group->needs_poll list.
Then spdk_nvme_poll_group_process_completions() polls all qpairs in
the group->needs_poll list and hits the assert.
Fixes the issue #2390
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I6ede8bd3b7b1a57a34ac61436159975ab6253fbe
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11882
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
SPDK can submit more commands to remote NVMf target than allowed by
negotiated queue size. SPDK submits up to SQSIZE commands, but only
SQSIZE-1 are allowed.
Here is a relevant quote from NVMe over Fabrics rev.1.1a ch.2.4.1
“Submission Queue Flow Control Negotiation”:
If SQ flow control is disabled, then the host should limit the number
of outstanding commands for a queue pair to be less than the size of
the Submission Queue. If the controller detects that the number of
outstanding commands for a queue pair is greater than or equal to the
size of the Submission Queue, then the controller shall:
a) stop processing commands and set the Controller Fatal
Status (CSTS.CFS) bit to ‘1’ (refer to section 10.5 in the NVMe Base
specification); and
b) terminate the NVMe Transport connection and end the association
between the host and the controller.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: Ifbcf5d51911fc4ddcea1f7cde3135571648606f3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/11413
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
spdk_nvme_poll_group_remove() is available only for disconnected
qpairs now. Hence spdk_nvme_poll_group_remove() does not have to
check if qpair is connected and call nvme_ctrlr_disconnect_qpair().
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I3b05246c4be6adfa3392b8f0e5ecaf274a8a7795
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10846
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
Previously, when connecting qpair, we allocated stats per qpair
if poll group is not used or we set stats per poll group otherwise.
Then when removing qpair from poll group, we cleared qpair->stats pointer.
However, if qpair is still not completely disconnected after removing
qpair from poll group, tqpair->stats is NULL and it causes a segmentation
fault.
Hence we set tqpair->stats to &g_dummy_stats instead of NULL.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: Ice6469627ce8d4bf4567f57c304759206b6432f1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10844
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This is necessary to failover another path when multipath is configured.
Signed-off-by: Shuhei Matsumoto <smatsumoto@nvidia.com>
Change-Id: I0b6bcf63501e38f75efb4b0d6bec58abb4b67aef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10250
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
spdk_nvme_ctrlr_free_io_qpair can be called when
qpair is already disconnected. In that case qpair's
state is changed to NVME_QPAIR_DESTROYING and
transport's ctrlr_delete_io_qpair callback is
called. RDMA and TCP transports call
nvme_transport_ctrlr_disconnect_qpair in
the callback and since qpair's state is
not DISCONNECTED or DISCONNECTING, qpair
is disconnected for the second time.
If spdk_nvme_ctrlr_free_io_qpair is called
when qpair is in ENABLED state than nothing
changes, qpair will be disconnected before destroy.
PCIE/vfio_user don't implement transport disconnect
callback, so they are not affected.
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I23e11856ecafb51669acf4a3118be049c11eecda
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/10326
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
When data digest is enabled for a nvme tcp qpair, we can use accel_fw
to calculate the data crc32c. Then if there are multiple
c2h pdus are coming, we can use both CPU resource directly
and accel_fw framework to caculate the checksum. Then the datao value compare
will not match since we will not update "datao" in the pdu coming order.
For example, if we receive 4 pdus, named as A, B, C, D.
offset data_len (in bytes)
A: 0 8192
B: 8192 4096
C: 12288 8192
D: 20480 4096
For receving the pdu, we hope that we can continue exeution even if
we use the offloading engine in accel_fw. Then in this situation,
if Pdu(C) is offloaded by accel_fw. Then our logic will continue receving
PDU(D). And according to the logic in our code, this time we leverage CPU
to calculate crc32c (Because we only have one active pdu to receive data).
Then we find the expected data offset is still 12288. Because "datao" in tcp_req will
only be updated after calling nvme_tcp_c2h_data_payload_handle function. So
while we enter nvme_tcp_c2h_data_hdr_handle function, we will find the
expected datao value is not as expected compared with the data offset value
contained in Pdu(D).
So the solution is that we create a new variable "expected_datao"
in tcp_req to do the comparation because we want to comply with the tp8000 spec
and do the offset check.
We still need use "datao" to count whether we receive the whole data or not.
So we cannot reuse "datao" variable in an early way. Otherwise, we will
release tcp_req structure early and cause another bug.
PS: This bug was not found early because previously the sw path in accel_fw
directly calculated the crc32c and called the user callback. Now we use a list and the
poller to handle, then it triggers this issue. Definitely, it will be much easier to
trigger this issue if we use real hardware engine.
Fixes#2098
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I10f5938a6342028d08d90820b2c14e4260134d77
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9612
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Enable dump of transport stats in functional test.
Update unit tests to support the new statistics
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I815aeea7d07bd33a915f19537d60611ba7101361
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8885
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This function may return an error and we should handle it
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I996ceb6e300bd9527385aded9068b2841e94a20d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9278
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
nvme_transport_poll_group_remove() clears qpair->poll_group. Hence
we should not use it after that.
Fixes#2170
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I57ceee8c66684e2d02b51b8a0f3d66aacbcb9915
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9560
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: GangCao <gang.cao@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Dong Yi <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This allows for creating admin qpair in an asynchronous mode and I/O
qpairs based on what the user specified in spdk_nvme_io_qpair_opts.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I1801ea76d5a08b1bdc558eb0f18648f59454b654
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9077
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
This will allow us to call `connect_qpair_poll()` from
`process_completions()`. Otherwise, `nvme_fabric_qpair_connect_poll()`
which calls `process_completions()` might create a loop, which can cause
issues with `nvme_completion_poll_status` used for tracking the CONNECT
command by the fabrics code.
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: Ibd67bc3e011b238db264394e005b3268624cceef
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8623
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
The fabric connect command is now sent without. It will make it
possible to make `nvme_tcp_ctrlr_connect_qpair()` non-blocking too by
moving the polling to process_completions (this will be done in
subsequent patches). Additionally, two extra states,
`NVME_TCP_QPAIR_STATE_FABRIC_CONNECT_SEND` and
`NVME_TCP_QPAIR_STATE_FABRIC_CONNECT_POLL`, were added to keep track of
the state of the connect command. These states are only used by the
initiator code, as the target doesn't need them.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: I25c16501e28bb3fbfde416b7c9214f42eb126358
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8605
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
There may be multiple C2H data pdus recevied.
So we should use the following steps:
1 Use the SPDK_NVME_TCP_C2H_DATA_FLAGS_LAST_PDU
to check whether it is a last pdu or not.
Then we will not cleanup tcp_req, i.e., tcp_req->datao
will not be cleaned.
Then use the SPDK_NVME_TCP_C2H_DATA_FLAGS_SUCCESS
to check whether the controller will use resp pdu
or not.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I9dccf2579aadd18f31361444e25bd4b3b76f06c5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/9192
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This will be done in stages. This patch adds the
nvme_tcp_ctrlr_connect_qpair_poll function and and makes the icreq step
asynchronous. Later patches will expand it and make the
nvme_fabric_qpair_connect part asynchronous as well.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Change-Id: Ief06f783049723131cc2469b15ad8300d51b6f32
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8599
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Needed to make this code path asynchronous.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I6b18d4e9fc1a29b30c78f7f087b80913d00f9726
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8598
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
async_mode option is currently supported in PCIe transport layer
to create io qpair asynchronously. User polls the io_qpair for
completions, after create cq and sq completes in order, pqpair
is set to READY state. I/O submitted before the qpair is ready
is queued internally. Currently other transports only support
synchronous io qpair creation.
Signed-off-by: Monica Kenguva <monica.kenguva@intel.com>
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ib2f9043872bd5602274e2508cf1fe9ff4211cabb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8911
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
.ctrlr_connect_qpair
Previously this was assumed to be a synchronous process so the generic
layer transport code updated the state after .ctrlr_connect_qpair
returned. In preparation for making this support asynchronous mode,
shift that responsibility down into the individual transports.
While none of the transports actually do this asynchronously, insert a
busy wait in nvme_transport_ctrlr_connect_qpair to wait for the qpair to
exit from the CONNECTING state. None of the upper layer code can
actually correct handle a transport doing this asynchronously, so the
busy wait will cover that.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I3c1a5c115264ffcb87e549765d891d796e0c81fe
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8909
Community-CI: Broadcom CI <spdk-ci.pdl@broadcom.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Monica Kenguva <monica.kenguva@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For receving the pdu, we add the crc32c offloading by Accel framework.
Because the size of to caculate the header digest size is too small, so
we do not offload the header digest.
Change-Id: If2c827a3a4e9d19f0b6d5aa8d89b0823925bd860
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7734
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Connect the adminq as part of controller initialization
instead of controller construction.
We never actually 'connected' the adminq for
PCIe or vfio-user transports, since its a nop.
But their connect_qpair transport ops function
is also a nop for the adminq, so it's fine to
generically connect the adminq across all transports.
Note that we cannot read registers (cc or csts)
during controller initialization now until after
the adminq has been connected since reading fabrics
registers depends on a connected adminq. This gets
special cased for now, but eventually reading
cc and csts will need to be part of the state machine
itself to make it asynchronous.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ia5566d7c549d78d24b94ea253df51e697da6237f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8079
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
According to NVMe-oF 1.1 spec, it is not a fatal error.
So according to Figure 126 in NVMe Base specification,
we should return "Transient Transport Error".
Change-Id: I601304ae2bb24508882fb1ec8c7e53ec587ab515
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7795
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Read CAP (Capabilities) register as part of controller
initialization instead of controller construction.
For now, still read CAP in the pcie and vfio-user
controller construction, since they need the
drstd (doorbell stride) to construct the admin
queue.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I000fe880f2ec0d6de1d565c883d7ea0ae1ac2c81
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8078
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Read VS (Version) register as part of controller
initialization instead of controller construction.
This prepares for upcoming changes to make
controller attach fully asynchronous. Since reading
fabrics registers is an asynchronous operation, it
will be easier to read the VS register as part of
controller initialization which operates as an
asynchronous state machine.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I771386dbdf5902633e0d9f91b3b20be98f26fdc3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8076
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Since we will reuse send_pdu for other purpose in the next
patch.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Iee5166131b70a25bc13aaa847bfc9066231f31a9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8028
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Community-CI: Mellanox Build Bot
For nvme/tcp connection, we use the synced manner
if the qpair is not fully connected. Thus without
the check, we will stuck here. And this patch
fixes this issue.
Change-Id: I72815bf5b4c0b31c4866bc1b9034b0e42b81d3f1
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8025
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Mellanox Build Bot
The header size is very small, which does not have too much value to
offload such calculation by hardware.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Iaa82f39312df7eef3282325a33677ea41ab735ab
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8011
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
The purpose is to prepared for implement the async crc32 caculation
in the future patch.
Change-Id: Ia75f28154c49f08b527d48c63b9da79a6bdfede8
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7794
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This is prepared for using the hardware offloading
engine in accel framework. And some fields in nvme_tcp_pdu
needs to be DMA addressable.
Change-Id: I75325e2cd7ff25fe938bea0ac9489a5027e3e0e9
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7770
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
If the qpair is part of a poll group, the socket will get
flushed as part of polling that group already. We only need
to explicitly flush to handle the case where the qpair is
not in a poll group.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Ib2a510b6d26d1622950437d81e0a40f6b15d6b54
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7049
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
There was a fix for this that went into the posix layer, but the
underlying problem is the logic in the nvme/tcp transport. Attempt to
fix that instead.
Change-Id: I04dd850bb201641d441c8c1f88c7bb8ba1d09e58
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6751
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Remove the polling group check. Because at this moment,
the qpair is not added into a polling group. If we do
not remove it, we will never enable zcopy feature for
I/O qpair.
And in sock implementmentation, we already fixed the zero copy
handling if a socket is not in a polling group. See
posix_sock_flush function. So we can fix this issue if we directly
remove this check.
Reported by: Aleksey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I969936c4b6c7f13cbfa4d6eb479010c53f3e384a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7056
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
This patch refactor the pdu sending logic with the async manner,
then if the group contains the accel engine, we can use it.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I2d669c0a3255d7a8898441e406906add2f3a3556
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6759
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
It is invalid to try to delete a NULL qpair, so do
not check for it in nvme_tcp_ctrlr_delete_io_qpair and
return an error when NULL. Just change it to an
assert instead. This makes it consistent with pcie
and rdma.
While here, add an assert in rdma as well.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ic2f76deecb21b78749dac85e33fb1fa0d14a1239
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6917
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: <dongx.yi@intel.com>
Previously the callback parameter for this function is NULL, this will
cause segment fault, so pass the correct parameter here.
Fix#1817
Change-Id: Ie768b7bf4a72862d16a44742ab3032803d0939a2
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6690
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Community-CI: Mellanox Build Bot
Purpose: To get the optimal group, we need the socket information.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: I17b048a402fbf002307dd225f64b20a9f876d642
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/3324
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Mellanox Build Bot
Add the real support in nvme tcp transport.
Change-Id: I2aa9b0284d6fe009925e67f602a055e787f77987
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5734
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
No need these returns at the end of void functions.
So remove them.
Signed-off-by: yidong0635 <dongx.yi@intel.com>
Change-Id: I8889745f3ef82af513d03259a77a33c1f4f536cb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6015
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
In the next patch this member will be used to track
both read and write offsets
Change-Id: I852125ff35257f9821ddf4a641d96afb29ebf0a0
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5924
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There is a problem with TCP zcopy enabled:
1. TCP initiator sends icreq and start polling a qpair. Polling of qpair
actively calls nvme_tcp_read_pdu function
2. nvme_tcp_read_pdu: qpair is in NVME_TCP_PDU_RECV_STATE_AWAIT_PDU_CH state,
it reads 8 bytes of common PDU header. It determines the type of the PDU
and finds the size of PDU_PSH header.
3. nvme_tcp_read_pdu: qpair is in NVME_TCP_PDU_RECV_STATE_AWAIT_PDU_PSH state.
It should read 120 bytes of icresp PDU. The number of bytes which needs to be
read is pdu->psh_len - pdu->psh_valid_bytes. qpair receives 120 bytes
(the full PDU) and calls nvme_tcp_pdu_psh_handle -> nvme_tcp_icresp_handle.
Here we check that we haven't yet received buffer reclaim notification and
simply return from this function. At the same time we continue to poll the qpair.
4. nvme_tcp_read_pdu: qpair is in NVME_TCP_PDU_RECV_STATE_AWAIT_PDU_PSH state
and tries to read data from a socket again. The number of bytes is
pdu->psh_len - pdu->psh_valid_bytes. But now pdu->psh_len == pdu->psh_valid_bytes,
so we call nvme_tcp_read_data with zero length.
readv with zero length is commonly used to check errors on the socket,
but in our case there is no errors and readv returns 0.
5. nvme_tcp_read_data treats zero as error and return NVME_TCP_CONNECTION_FATAL.
Fix is to handle icresp, but leave qpair in INITIALIZING state until
we receive acknowledgement for icreqsend_ack. We also move qpair to
NVME_TCP_PDU_RECV_STATE_AWAIT_PDU_READY recv_state so recv_pdu
will be zerofied and qpair will try to read a common PDU header.
But since it is not initialized yet, it won't receive anything
from the target.
Fixes issue #1633
Change-Id: I22cedefe530a8ac3b51495988ed6265d8fad15bb
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4969
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
According to the SPEC we should support up to 8192 bytes
of ICD for admin and fabric commands. Transport configuration
parameter in_capsule_data_size is applied to all qpair types -
admin and IO. Also we allocate resources when we get a connection
request, so we don't know qpair type at this moment.
Create a list of buffer in TCP poll group to support ICD up
to 8192 bytes when configuration ICD is less than this value.
The number of elements in this pool is hardcoded, it is planned
to add a new configuration parameter later.
Fixes issue #1569
Change-Id: I8589e3e2ea95d515f5503c6de7c1ee40aaf7b6da
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4754
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The current approach checks "rc == 0". It worked before adding
polling of poll group since a single qpair should return 1
completion for its own icreq while poll group can return
several completions for all qpairs attached to this poll
group (but .e.g not for those qpair who is waiting for the
completion).
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Change-Id: I60d05d8d6640e4e2bbaf3cd533d2f5a3637adea1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4768
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch removes the string from register component.
Removed are all instances in libs or hardcoded in apps.
Starting with this patch literal passed to register,
serves as name for the flag.
All instances of SPDK_LOG_* were replaced with just *
in lowercase.
No actual name change for flags occur in this patch.
Affected are SPDK_LOG_REGISTER_COMPONENT() and
SPDK_*LOG() macros.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I002b232fde57ecf9c6777726b181fc0341f1bb17
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4495
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Mellanox Build Bot
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI
We can receive buffer reclaim notifications only when a qpair is
attached to a poll group (so qpair's socket is connected to a socket
poll group).
The previous assumption that we enable zcopy only for IO qpairs was
wrong since IO qpair might not use poll groups too (e.g. abort
application).
Fixes issue #1607
Change-Id: I67329d755d81da6606e65eddfeceb20839346d87
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4476
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This seems to be causing some CI test failures. So
disable zero copy in all cases for now for client
sockets.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Iceea09fe65fb90c7df15f500878a473f1ad4152c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4473
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
In NVME TCP initiator zero copy is enabled for IO qpairs
and disabled for admin qpairs
Change-Id: Ibdf521dccde9b95ec5dd15a5eb2baed8fcf8b88e
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4211
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
A preparation step for enabling zero copy in NVMEoF TCP initiator.
With zero copy enabled, some requests might be completed out
of "process_completions" call and we should take them into
account to return the correct number of completions.
Change-Id: Iba7973f6da815645bbfad0334619d46b66379226
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4209
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
A preparation step for enabling zero copy in NVMEoF TCP initiator.
We should wait for both events to occur before continue qpair
initialization.
Add a new bit to nvme_tcp_qpair::flags to track receiving of icreq ack
since icreq is sent without tcp_req and there is no way to apply
existing synchronization mechanisms.
Move tcp qpair to initializing state if we receive icresp before icreq ack,
this state will be checked during handling of icreq ack to continue
qpair initialization
Change-Id: I7f1ec710d49fb1322eb0a7f133190220b9f585ab
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/4207
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
