This makes them easier to find. They are now named
spdk_nvme and spdk_bdev.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I1f6736d8f7f5b9669583731fb0b710ba54f0d50a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2679
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
This will open up the way for probing and connecting to
all of the namespaces on a pci controller.
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: I8fa3dde9f249ce826659882e66f630b8c25e2701
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2779
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
As we have done for SPDK reactor, SPDK thread termination needs communication
among SPDK threads. So At application shutdown, create the while loop
until all threads are destroyed and in the loop, check each thread
is exited, and destroy the thread if exited or mark it as exiting
and retry checking after traversing other threads.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I7a1008b95f3303de17449d574e917eb47cbe54b5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2660
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
I think the main point of having unused qpairs in
the perf application is to simulate the performance
drag of having active qpairs sitting idle on an application.
If we don't poll these unused I/O qpairs, there is no real performance
effect (in terms of cache evictions, wasted cycles or otherwise).
Signed-off-by: Seth Howell <seth.howell@intel.com>
Change-Id: Ie67223eae57a9bfbfaa703a401b0960f88552e11
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2008
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We only enable this feature for READ commands in the NVMe driver, so
also ignore the WRITE commands in fio plugin tool.
Change-Id: Iecf43326e1a2a3b3540a1391e09a33d2443bd546
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2730
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This only covered one test case for NVMe reservation feature, so remove
it to test directory.
Change-Id: I7920679ce14dd4d6a9164cb7663016bc7a3a4929
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2732
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
When testing the application, after release the reservation, the
registrant is still there, so we need to unregister the registrant
at last to restore the drive to a clean state.
Also set the CPTPL to 10b, it means Reservations are released
and registrants are cleared on a power on, we will move the tool
to test/nvme directory in following patch as this is only one
test case for NVMe reservation feature.
Change-Id: I271a61985940958b9f36887f9cd97841841ba2d6
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2731
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Optionally let the user specify what % into the buffers there should
be a miscompare if desired.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I3a5524de5e0f7cb91fcf92e76f937bdf280a515b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2109
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
current_queue_depth should have been incremented only if I/O submission
succeeded.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibdcae2d4e8d5b804faaac2392226252c95dfb634
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2586
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add simple periodic round robin poll group migration to the example
application to exercise SPDK thread dynamic scheduling.
Add CLI option to enable the feature manually. Default setting is
disabled, and the period is specified as micro second.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I4639e94ce00611a600ff068e754ee6f31905565c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2556
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Add the flag, resched, to struct nvmf_lw_thread.
Add an new function nvmf_request_spdk_thread_reschedule() to set
the resched flag of the current thread to true.
nvmf_reactor_run() checks the resched flag and call
nvmf_schedule_spdk_thread() and clear it if it is true.
Enable the thread operation SPDK_THREAD_OP_RESCHED and add
nvmf_request_spdk_thread_reschedule() to the case of
SPDK_THREAD_OP_RESCHED in nvmf_reactor_thread_op().
Following patch will add repeated calls to spdk_thread_set_cpumask()
to exercise the feature.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I60a4213c139b3e6f16ccb7065dea34ffe760de13
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2541
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Replace mutex and linked list by lockless ring for nvmf_reactor->threads.
If we create event call, we will be able to keep linked list and
remove only mutex. However, simple replacement of locked linked list
by lockless ring will be enough for now.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I590a385ff018ad20c7d6752b0a3a5562e3b68510
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2579
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Stop creating the default lightweight thread per POSIX thread. Additionally,
substitute the created master thread into g_init_thread directly as a
preparation to the next patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I09643491e6b5aaf91d9958481f05e264a2ac5f7d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2542
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Replace spdk_thread_lib_init() by spdk_thread_lib_init_ext() to
support dynamic SPDK thread scheduling in this sample application.
Add nvmf_reactor_thread_op() and nvmf_reactor_thread_op_supported(),
and then pass them by spdk_thread_lib_init_ext().
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9498d45d74757d8893b2b415fe28bf65f8fd02d6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2540
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
By following the SPDK NVMe-oF target application, create and destroy
a lightweight thread per poll group instead of assuming a pool of
lightweight threads already exist at start up time. Each poll group
is only accessed from the associated lightweight thread.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I0a221594d51373237f4ead07a3f5592dbbffa7a2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2539
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
if spdk_thread_poll() calls spdk_thread_create() to create SPDK
thread dynamically, it will acquire nvmf_reactor->mutex and will
cause deadlock because the queue nvmf_reactor->threads is accessed
by any POSIX thread by holding nvmf_reactor->mutex.
If any non-owner POSIX thread manipulate nvmf_reactor->threads by
holding nvmf_reactor->threads, like general priority based scheduler,
running SPDK threads by FIFO will be better.
Change nvmf_reactor_run() to dequeue a SPDK thread from the head, run
it, and then enqueue it to the tail. Release nvmf_reactor->mutex
while spdk_thread_poll() is executed.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9b4040cc4d995beaf4a1f9ed8260bb1254d7d7fb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2537
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
nvmf_schedule_spdk_thread() is not so performance critical but
should work as designed. Guard the whole operation to decide the target
core by g_mutex. This matches the reactor's _reactor_schedule_thread().
If _reactor_schedule_thread() is refined, change this accordingly too.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9382230577442897d4d2d22b85b1ae4edd77aa98
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2536
Community-CI: Mellanox Build Bot
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The spdk_opal_supported() is redundant with spdk_opal_dev_construct(),
because we only return the spdk_opal_dev structure when the drive
can support OPAL feature.
Change-Id: Ieadf271a0c8530f2440cded05ad139483a8c5937
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2383
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This is more to exercise the various CRC-32C back ends than anything
else but will calc a CRC on the source data and if -y is
specified it will also calculate SW (ISA-L)f defined CRC-32C and
compare every operation against what the accel engine came up
with using whatever back-end was enabled.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I5ecd3c474717bce4e46d75875a784f888052993e
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2073
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The capacity is calculated without single block size.
Correct the calculation.
Change-Id: I039e4dbdfc00f5d29148efc2c2a553535b7daf70
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2367
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Xiaodong Liu <xiaodong.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The spdk_opal_supported() is redundant with spdk_opal_dev_construct(),
because we only return the spdk_opal_dev structure when the drive
can support OPAL feature.
Change-Id: I2a8b70aa92828cf60d168dcf2985759e0eb9a6e3
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/2217
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Need to check that a valid workload type was specified and print
usage if not.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ib956e28f9049e49f19adcc09e861db42034799b8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1900
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Recent CMB changes disable using the CMB copy and submission queue
at the same time, so disable use_cmb_sqs by default.
Also spdk_nvme_ctrlr_map_cmb() changed the "size" parameter used as
size of buffer that was mapped, so change it here too.
Change-Id: If957674042b7f4a08e272bf5f9f2ee29f50805cb
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1955
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
For the purpose to enable the stress test with Bit Bucket SGL,
here we added one new parameters: "bit_bucket_data_len".
For testing it, user should set "enable_sgl=1" and
"bit_bucket_data_len=4096". This means total 4096 Bytes of
data will be described by Bit Bucket SGL, note that the value
should be less than block size specified in the fio command
line.
We will count the Bit Bucket data from the beginning of each
I/O for simplification.
Currently it's only valid for READ test. User can see the
performance improvement when enabled the Bit Bucket.
Change-Id: Ia481a324c25942d6ca051c71cb90f87d21955259
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1623
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Instead of creating an allocator where the driver manages the space,
now, since using the CMB for queues and data has already been
disallowed, just create functions to map and unmap the entire CMB.
The user can manage the space.
Change-Id: I023994deda3b517e14d2ba464c7375bf22b58456
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/785
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Usable with both ioat and upcoming idxd modules.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: Ie25743854aa6a05d1b5f580ea64fb5c7d7c722d1
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1720
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We will be create fine name for each poller but it will need large
effort. Replacing spdk_poller_register by the macro SPDK_POLLER_REGISTER
will provide better name than function address with minimum effort.
Following patches may improve function name for clarification.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: If862a274c5879065c3f7cb04dcb5ca7844523e68
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1781
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Maciej Szwed <maciej.szwed@intel.com>
Community-CI: Broadcom CI
This change will make sure that ioat_perf application
exits with error code 1 whenever there was
no test performed.
Mainly by checking number of ioat channels available.
Other changes made to align with returning 1 on error.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Id94fa947fd097d5085285d3348aeb41ff280e731
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1672
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
This change will make sure that verify application
exits with error code 1 whenever there was
no test performed.
Mainly by checking work_fn return code.
Other changes made to align with returning 1 on error.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I28a36dd5d5adb50bb4f54b1cc724c80da96af564
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1671
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
In show_blob(), value_len of xattr contains terminator '\0',
which is printed as '.' when calling spdk_log_dump().
For example, we set key/value pair as <key1,xattr value>, we get
"xattr value." but not "xattr value" when showing blob info.
Skip '\0' will fix this.
And "data[BUFSIZE]" seems redundant here, remove it.
Signed-off-by: Richael Zhuang <richael.zhuang@arm.com>
Change-Id: I4e7c3276e51f14badf43b660b80b24ae85bb0900
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1745
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Following patches will require thread termination so that thread_exit()
will move thread to exiting, thread_poll() will move thread from
exiting to exited, thread_is_exited() will detect the threadis exited,
and then call thread_destroy().
So change all places as a preparation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I6b2e8aee5ed7cd160a88b4c9aaed7d90bd9dac07
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1640
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
FIO in our scripts is usually run as follows: (more or less)
fio_bdev /path/to/job.fio --spdk_json_conf=/path/to/spdk.json
--filename="$(discover_bdevs /path/to/spdk.json --json)"
The bdev names are usually hardcoded in the json config, but still,
they have to be provided to fio again. Not anymore - just use
--filename=* and FIO will use all available bdevs as I/O targets,
just as if all filenames were provided.
The above command could be now simplified to:
fio_bdev /path/to/job.fio --spdk_json_conf=/path/to/spdk.json --filename=*
Change-Id: I56a02e56877b138429d68fb24f1a383c6700c4f4
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1542
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Commit 8c1d107 added a new erase API and renamed the original
API with "secure_" prefix according to the specification, as the
secure one will not cryptographically erase user data, due to
the limitation from the drive, only the secure API can be
supported, so changing the caller to use the original again.
Change-Id: I25cb054e728065d9ae9c6c30aa0ab374d60cf6f6
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1519
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
In spdk_fio_setup when the connections are too many,
for example 16 subsystems, it would take too much time to
complete the probe. And it takes the mutex that makes the
poll_ctrlr function can't send the keep alive cmd which
causes the target timeout. Split the mutex so the poll_ctrlr
has the chance to sent keep alive.
Fixes issue: #1286
Change-Id: I300513b5e8761d9eaadb4c5cbc8ed97fe84d02df
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1407
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Actually we can just use one API to finish the requirement.
Change-Id: Ia0d3d589755e8c92f636d3d090ec642299511401
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1280
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The APIs even don't have a chance to be called if the drive can't
support OPAL feature, so just remove the NULL check, and we will
store level 0 discovery descriptors after initialization, so
spdk_opal_cmd_scan() isn't necessary here, remove it as well.
Change-Id: I24f12f2c352996d9ebe76dc015cd0b7502798359
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1231
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The next patch will create poll group threads dynamically for
NVMe-oF target, and will need to wait for completion of poll group and
I/O channel destroy. This is a preparation for the next patch.
Add callback function and its argument to spdk_nvmf_poll_group_destroy(),
and to struct spdk_nvmf_poll_group, respectively.
The callback has not only cb_arg but also status as its parameters even
if the next patch always sets the status to zero. The reason is to follow
spdk_nvmf_tgt_destroy's callback and to process any case that the status
is nonzero in future.
spdk_nvmf_poll_group_destroy() sets the passed callback to the passed
poll group.
Then spdk_nvmf_tgt_destroy_poll_group() calls the held callback in the
end.
This change will ensure all pollers are being unregistered and
all I/O channels are being released.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifb854066a5259a6029d55b88de358e3346c63f18
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/495
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Supports SW accel engine, CBDMA accel engine and eventually the DSA
accel engine through common API. Basic functions only are included
here, subsequent patches will add more features as needed. For
example, the verify function is very crude right now.
Tool output was compared to the ioat perf tool w/CBDM and results
are very close although there a small penalty for using the
framework.
For CBDMA, start the app with --wait-for-rpc and run the ioat scan
RPC with desired whitelist. If there are not enough channels
(channels are not a concept in the framework) then SW accel engine
will be used for cores that could not get a channel.
Signed-off-by: paul luse <paul.e.luse@intel.com>
Change-Id: I9c5ab33e74db7bdbc5bfe5d7a08cc7ffaeab625b
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/883
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The macro is defined by the spec, so place this value to where
it should belong.
Change-Id: I23f91662fd4ab279aa4285212fc8cbd2ed42245b
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1126
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Since the OPAL here is just for NVMe device, so we don't need to use dev_handler as common
handler, just rename it to spdk_nvme_ctrlr. And we don't exit the initialization if
OPAL construnction had a failure. Also move the timeout initialization to construct().
Change-Id: I11f0aea961eaa3da0c6253eb03d0227f7e7e5f11
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1101
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
No actual logic change except re-define some data structures.
Change-Id: Id0a483071591beee675cbc3ef368ac1fb723cfe0
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/1099
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Currently an option is implemented to monitor a correlation between the
core and namespace.
Previously:
==================================================================
Device Information
RDMA (addr:1.1.75.2 subnqn:nqn.2016-06.io.spdk:cnode1) from core 0:
RDMA (addr:1.1.75.2 subnqn:nqn.2016-06.io.spdk:cnode1) from core 0:
==================================================================
Now:
========================================================================
Device Information
RDMA (addr:1.1.75.2 subnqn:nqn.2016-06.io.spdk:cnode1) NSID 1 from core 0:
RDMA (addr:1.1.75.2 subnqn:nqn.2016-06.io.spdk:cnode1) NSID 2 from core 0:
========================================================================
Signed-off-by: Alla Kiseleva <c_allaki@mellanox.com>
Change-Id: I35e39c62bbdac05152f35e11eb1d560eb0e50404
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/955
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
