For NVMe/TCP target, data segments which correspond to H2C or C2H PDU
will have any alignment. spdk_dif_set_md_interleave_iovs() have allowed
reading data to have any alignment but had required data segment to
be a multiple of block size.
In other words, spdk_dif_set_md_interleave_iovs() had required that both
ctx->data_offset and (data_offset + data_len) must be a multiple of the
data block size.
This patch refines the algorithm to remove the latter requirement.
The update implies that spdk_dif_set_md_interleave_iovs support any
data buffer whose size is less than a single data block.
The update doesn't change parameters of spdk_dif_set_md_interleave_iovs
and existing UT should be passed.
This patch adds additional UT code to test these updates.
Change-Id: I88c7d2a80a8d92b54863b6ad1c3a9d2761a6195d
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457542
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
This patch adds mechanism to simulate power failure in
blobstore unit tests at any given moment in time.
This point in time is measured by number of IO operations
occured after triggering power failure with the number
of IO operations given as a parameter. Number of IO
operations parameter can be defined as any type IOs,
writes, reads, unmaps, writes zero or flushes.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I7be45331bb5110f6c16f01fd7c4e7984b2d1977d
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454451
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
This bug was found by code inspection. When PDU read restarts
after data segment, iov_offset must be reduced by data length.
However iov_offset had been reduced by buffer length by mistake.
Lack of UT code was the main reason of this bug. Hence add UT
code to test the fix of the bug together in this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I74f2f6ae8dca2e78a64bfdef8080c8031dfabb87
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/458530
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
If bdev is configured to use separate buffers for metadata transfer,
but it doesn't support the write zeroes command, pass empty zeroed
buffer to make sure the metadata is cleared out as well.
Change-Id: If6f024266067e5764a28a276296f651d31da4792
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457628
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Starting with this patch it is possible to remove a
snapshot if there is only a one clone created from it.
In such case snapshot can be removed without any data
copying. This is achieved with following steps (case
with only one clone):
1. Open snapshot (Snapshot1) that shall be removed
2. Check if the Snapshot1 has no more than 1 clone (Clone1)
3. Remove Clone1 entry from Snapshot1
4. If the Snapshot1 has a parent snapshot (Snapshot2):
4a. Add Clone1 entry to the Snapshot2 clones list
4b. Remove Snapshot1 entry from Snapshot2 clones list
5. Open Clone1 blob
6. Freeze I/O operations on Clone1
7. Temporarily override md_ro flag for Snapshot1 and Clone1
for MD modification
8. Merge Snapshot1 and Clone1 clusters maps into Clone1
clusters map
9a. If Snapshot2 is present switch parent ID and backing
bs_dev on Clone1
9b. If Snapshot2 is not present set parent ID to
SPDK_BLOBID_INVALID and backing bs_dev to zeroes_dev
10. Sync MD on Clone1
11. Sync MD on Snapshot1
12. Restore MD flags for Clone1 and Snapshot1
13. Unfreeze I/O on Clone1
14. Close Clone1 blob
15. Remove Snapshot1
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I800724b981af894e01e1912d0077c5b34a2ae634
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/445576
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
SQSIZE parameter validation in Connect command was broken because QID
field in qpair was used before intialization.
Signed-off-by: Evgeniy Kochetov <evgeniik@mellanox.com>
Change-Id: I8a0b359937d661df3b9888e6084e7d0b4a9056ea
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455667
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
In a test case of op_login_session_normal_test(), it is expected that
the tag of the session has any value different from the connection but
the tag of the session was not initialized.
Fixes#826
Reported-by: lorneli <lorneli@163.com>
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I62f7a4bd301c5a74ad6ba10b1b448189f750b324
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/458339
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Lorne Li <lorneli@163.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This patch changes the meaning of the data_len parameter of
spdk_dif_set_md_interleave_iovs from `Expected data length of the payload`
to `Expected length of the newly read data in the extended LBA payload`.
This change will align the parameters of spdk_dif_set_md_intereleave_iovs
to of spdk_dif_generate_stream.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I7f9c45e78be977625713acb79d2ae82d4375f419
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457543
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
This patch adds the UT regarding below function
iscsi_op_login_session_normal()
It covers the target related, connection related
and session related operations.
Change-Id: I570df82df850a0b359b2d57b4e1694d8cb16de37
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457925
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
NVMe bdev module support separate metadata now but NVMf subsystem
cannot process bdev with separate metadata yet.
Hence reject any bdev with separate metadata to be attached
explicitly by this patch.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I793c6c5f61deb766d7bf427ff67ccc57a48974cf
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457167
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
For reservation feature in NVMoF, we can't support the persist through
power loss feature, now we will add the configuration file parameter
with Namespace, after users set the configuration file parameter with
one NS, then the PTPL feature can be enabled.
Change-Id: Id72699093f7e68318b9529f7bacc5c9804f7f86b
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455905
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch uses the change by the last patch to initialize DIF
context in SCSI layer. Besides this patch changes the name of a
parameter from offset to data_offset to clarify the meaning.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I54bf1168ec5959432aa15dae0360c0640138b033
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457541
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Data offset are intended to correspond to DATAO in NVMe/TCP and
Buffer Offset in iSCSI.
Previously for iSCSI, buffer offset had been merged to start block
address, but passing buffer offset separately from start block address
clarifies the logic more.
On the other hand, for NVMe/TCP, passing DATAO separately from start
block address will be critically important because DATAO will bave any
alignment and will be necessary to use for not only reference tag
but also guard computation.
This patch adds data_offset to struct spdk_dif_ctx and adds it to the
parameters of spdk_dif_ctx_init(). ref_tag_offset is also added to struct
spdk_dif_ctx and it is computed by dividing data_offset by data_block_size
and is used to compute reference tag.
The next patch will use this change when getting DIF context in SCSI.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Id0e12ca9b1dc75d0589787520feb0c2ee0f844a5
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457540
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
DIF UT code had used numerics extensibly for complex DIF insert/strip
UTs. But numerics was error prone and difficult to follow the logic.
Hence this patch changes numerics to variables in DIF insert/strip UTs.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I40cb27167c068855dc5d1eb9e0f36818d39c73fa
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457539
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
data_offset to spdk_dif_generate_stream() was wrong but the function
worked as expected because the wrong data_offset was in the same
data block as the correct data_offset.
But the subsequent patches will refine spdk_dif_generate_stream()
and this bug will cause UT failure. Hence fix the bug up front.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I45f2302deaf377fda0ec5454c61fb463231a39db
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/457538
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Read requested range of lba map during relocation
instead whole lba map.
To read partial lba map range single move now has
three states: read, read_lba_map and write.
Free queue and write queue were merged to a single
move queue.
Change-Id: I86839f2286d42d4debf87cea40091370e5283b15
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454747
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Keep track of read lba map segments to avoid
unnecessary traffic in case ANM events.
Lba map is divided on 4KB segments which can
store 512 lba entries.
In case multipe read request on same segment
keep pending request list and process it in
read_lba_map() completion callback.
Change-Id: I2661bdb716ab7c975140e0b37aebcb17aa23901d
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453371
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
For the nvme device, I/Os are completed asynchronously. So we
need to check the outstanding I/Os before putting IO channel
when we hot remove the device. We should be sure that all the
I/Os have been completed when we change the sgroup->state to
PAUSED, so that we can update the subsystem.
Fix#615#755
Change-Id: I0f727a7bd0734fa9be1193e1f574892ab3e68b55
Signed-off-by: JinYu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/452038
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Almost all I/O callbacks in ftl utilize data in ftl_io, which is
initialized as callback argument in ftl_io_init_internal. This patch
changes the behavior to always returning the ftl_io struct in addition
to an extra opaque buffer.
Signed-off-by: Mateusz Kozlowski <mateusz.kozlowski@intel.com>
Change-Id: I611ab1b33575f599798a2bb65c231a724c852c7f
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455831
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Data block size was specified by mistake, and this patch changes
to use block size instead.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Icfb1df40438ef82211279b0b7c79036283744361
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/456292
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Keep lba map related fields in separate struct directly
in the band. Cleanup interfaces depended on ftl_md.
Lba map structure will be extended in next commit.
Change-Id: I1cfc2f2ff0c0e90bb63f39808780845673002e70
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453370
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Extended ftl_band_read_lba_map() interface to provide
range of lba map to read.
Added ftl_xfer_offset_from_ppa() function for
calculating offset of read portion of lba map
based on ppa address from IO. This offset is
used for coping read lba map portion to internal
ftl buffer.
Change-Id: I1c72a18c79eda8c33cd0b20ea36a5d9521a09d06
Signed-off-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/449435
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
SPDK_SUCCESS is a remnant and all other SPDK libraries have used
just 0. So this patch removes SPDK_SUCCESS from iSCSI library and
uses 0 instead.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ie33fd26238411e994ea9ea0c898da1abb502cad6
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/456928
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Data digest computation should take extended LBA payload but
could not do yet.
This patch adds an new API spdk_dif_update_crc32c() to compute
CRC-32C value for extended LBA payload.
In the next patch, spdk_dif_update_crc32c will be used in iSCSI
target first.
Change-Id: I327f384bb7dfd8b68279b0acec0ee78a40264a26
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/456171
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
we use this statement:
while (g_file->length_flushed != buf_length) {} in
file_length function.
It means that in this test case, length_flushed are
accessed by two different threads, so better to
use another new variable length_flused with volatile
before the variable definition. Then our ut will not hang.
Change-Id: I6152a4ba3f27f0fad1c8c2baa71324a36a2fb9e8
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/456580
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There's no need to set this every time we allocate
a request.
While here, fix a typo near where we needed to modify
the unit test to remove the qpair assertion.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I8af41a6c483415950f625d1ed2ef46088b75a622
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/456270
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
vring notification mechanism is transport-specific. At present, vhost
dataplane code in `lib/vhost/vhost.c` triggers guest notifications with
`eventfd_write()` system call. But this is an AF_UNIX specific
notification mechanism. This patch replaces `eventfd_write()` with the
existing generic `rte_vhost_vring_call()` function that is part of
DPDK's librte_vhost public API.
`rte_vhost_vring_call()` takes a vring_idx as an argument to associate
the `struct spdk_vhost_virtqueue` instance with the relevant `struct
vhost_virtqueue` instance. We introduce a new `vring_idx` field in
`struct spdk_vhost_virtqueue` to enable this association. This field is
initialized in `start_device()`. In addition, a stub for
`rte_vhost_vring_call()` is added in the vhost unit test file.
SPDK's internal `rte_vhost` copy will not be updated in order to support
the virtio-vhost-user transport. However, an `rte_vhost_vring_call()`
function is introduced in SPDK's `rte_vhost` in order to have a solid
API. This function is just a wrapper of `eventfd_write()`.
Change-Id: Ic93e25cd3f06e92f04766521bc850f1ee80b8ec8
Signed-off-by: Nikos Dragazis <ndragazis@arrikto.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454373
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Keep an array of iovecs tied to each IO. Internal IOs can have
iov_cnt > 1 without having to allocate additional memory. User's iovec
can now be modified too (e.g. when splitting the request).
Change-Id: Iec73c6dad59acdc331a1461fd7feac085138a8de
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455525
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
There's no point in synchronously returning an error from ftl_io_write
/ ftl_io_read as they're also reported in the IO's completion callback.
All errors are now reported through io->status.
Change-Id: I4adf4e13221b63715625276042e1172cd63b8f9b
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455521
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Some of the internal IOs split the contiguous data buffer into multiple
iovecs to separate the requests. It's unnecessary and can be replaced
by checking the position within the data buffer.
Change-Id: I9255ea0072fee6c4e6a7dca21e4008780bc45610
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455519
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
This isn't needed, and it actually results in warnings
when linking with LTO enabled.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I4e7dcd5d3f738fb3e53e35a1fff154a0e1ab06d3
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/456238
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Existing code in spdk_bdev_write_zeroes_blocks() will call spdk_bdev_free_io()
for the error case, which will cause assertion because the bdev_io isn't
submitted to the backend yet, so we will check the condtion first to
avoid the error case.
Change-Id: If27d78217f709a3315e74c00869d345abd6b9a69
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453491
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
All the SCSI commands have two states: allowed and conflict,
based on different reservation types and I_T nexus, the SCSI
module will check each commands before sending to the backend
device.
Change-Id: Ib05cece1c237873360f85c68d139362200d2d47e
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/436097
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add the unit test of the nvme ctrlr init delay to increase
the code coverage.
Change-Id: I0d31055fafc1ad13682496163e15de0a5f1e90e3
Signed-off-by: JinYu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455344
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
We flush a cache buffer once it's filled. When the write
for that cache buffer has completed, we look to see if
there's more data to flush. Currently if there's *any*
more data to flush, we will flush it, even if it's not
a full buffer.
That can hurt performance though. Ideally we only want
to flush a partial buffer if there's been an explicit
sync operation that requires that partial buffer to be
flushed. Otherwise we will end up writing the partial
buffer to disk, and then come back and write that data
again later when the buffer is full.
Add a new unit test to test for this condition. This
patch breaks one of the existing unit tests which was
designed specifically around a RocksDB failure condition.
Change that file_length unit test to now write exactly
one CACHE_BUFFER, which still tests the general logic
making sure that we don't confuse the amount of data
flushed with the value written to the file's length
xattr.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I83795fb45afe854b38648d0e0c1a7928219307a2
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455698
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Data can get implicitly flushed as cache buffers are filled. But
the length xattr is only written in response to a sync or close
operation. So we cannot just look at the amount of data flushed,
and ignore the sync operation if all of the data written has been
flushed - we still need to write the length xattr.
This also adds a unit test which reproduces the original problem.
Fixes issue #297.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Icca6ef4d1544f72e9bc31c4ee77d26b4b7f0cce4
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455692
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
For the latest TLC NAND, one write buffer unit (rwb batch)
needs to be spread over three PUs instead of being allocated
to a single PU for better sequential read performance
since the optimal write size(ws_opt) of 3D TLC NAND is
3 times bigger than the optimal read size(rs_opt).
I added num_interleave_units in 'struct spdk_ftl_conf'
to configure the number of interleaving units per ws_opt.
If num_interleave_units is set as 1, the whole of the ws_opt
blocks are placed sequentially around each PU.
If num_interleave_units is set as N, the 1/N of the ws_opt
blocks are staggered. So consecutively numbered blocks
are separated by ws_opt / num_interleave_units.
The sequential read performance is improved from 1.9GiB/s
up to 2.97GiB/S with this patch on our system. No performance
degradation is observed on sequential writes or
4KB random reads/writes.
Please refer to the Trello card for more details.
https://trello.com/c/Osol93ZU
Change-Id: I371e72067b278ef43c3ac87a3d9ce9010d3fcb15
Signed-off-by: Claire J. In <claire.in@circuitblvd.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450976
Reviewed-by: Young Tack Jin <youngtack.jin@circuitblvd.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Wojciech Malikowski <wojciech.malikowski@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
In some cases user may want to flag blob for removal
then do some operations (before removing it) and while
it happens there might be power failure. In such cases
we should remove this blob on next blobstore load.
Example of such usage is delete snapshot functionality
that will be introduced in upcoming patch.
Signed-off-by: Maciej Szwed <maciej.szwed@intel.com>
Change-Id: I85f396b73762d2665ba8aec62528bb224acace74
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453835
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
To establish a persistent reservation the application client shall first
register an I_T nexus with the device server. An application client registers
with a logical unit by issuing a PERSISTENT RESERVE OUT command with REGISTER
service action or REGISTER AND IGNORE EXISTING KEY service action.
Specify Initiator Ports (SPEC_I_PT) bit and All Target Ports (ALL_TG_PT) bit
are not supported for now, the registrants belong to the I_T nexus who sends
the command.
Also Activate Persist Through Power Loss (APTPL) bit will be supported in
following patches.
Change-Id: If057a764a4bfa73017f98048c94b697dbfa4b4a1
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/436088
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Apart from writing the data to OCSSD, mirror the latest two bands of
data on the persistent write buffer cache. Currently the data is only
sent there, further patches will add metadata support, shutdown recovery
and L2P updates.
Change-Id: Ief05d0c23fa0e25bd6085e0ce3e1528d6736d174
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/450266
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Adding these tests identified a small fix in the code under test
that is also included here. The compressdev 'produced' field
is unsigned and reduce is expecting a negative errno in the
callback.
Change-Id: I28ab11ee3ef54768a9d6ccd26282cf7dd022be43
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454806
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
When parent IO was splitted into several children requests, SPDK
may return parent completion callback with error status before
all the children requests are finished.
Change-Id: I63221a0ae1a5925a7fcd9744b4f5d8079c641252
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453611
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Lightweight threads may now be exited by calling
spdk_thread_exit() within the thread. The framework
polling the thread can release the resources associated
with that lightweight thread by calling
spdk_thread_destroy().
Change-Id: I6586b9d22556b3874fb113ce5402c6b1f371786e
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/455319
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Seth Howell <seth.howell5141@gmail.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
For UT there's no additional value in having more than 2 raid
devices, the value in having > 1 is in confirming the array
structures via create multiple and verify expected raids were
created.
Change-Id: I874b76644ccfc7d9dd307fbb179b35673b7bacc9
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454508
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
I'm testing the error paths within each function under test, this
was here simply because I copy-n-pasted much of the UT framework
from crypto to get it jump started.
Change-Id: Id7705bcaec87e93b589360e520b330f024d3293d
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/452723
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Note that much of the vbdev module is still WIP including this
function (ex there are rc checks at the end when nobody yet sets
an rc) but I want to catch up on UT before adding more new code,
or at least get close.
Change-Id: I4617c215fed9fe35a68dcc5e7ebc93e48588cf5b
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/452715
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Aas well as general test setup required for this one, additional
mocks, etc.
Had to add some asserts to make scan-build happy although I don't
see how these changes stimulated those failures.
Change-Id: Ief08f9b71ee7a836f6026d26517f5faa5f9d51ce
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/451688
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Test multi vector command that needs to be split by strip and then
needs to be split further due to the capacity of child iovs.
Add a case that was not tested before. In this case, the length of the
rest of iovec array with an I/O boundary is the multiple of block size.
Expect the rest of iovec array to be submitted in the completion of
previous iovec array.
Change-Id: I5b95b1f1884a73b31709b2fd9187a8a9e9b2cd0b
Signed-off-by: lorneli <lorneli@163.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/452414
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
It's 3 functions that are only called from this compilation
unit.
Change-Id: I033ced4c19ee2a33b9537c347532ea5706d02d6a
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454493
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Unclear why they were here to begin with.
Change-Id: Ic9b896796a9c56552972e3ef8075934d4b3f6497
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454515
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
No additional value in randomizing read vs write, which raid and
which channel. Still do read and write but fix the other values.
Change-Id: I5a4f023731119230d3eb49ae28421819144b90bc
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454509
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Having a varying QD in unit test isn't adding any value, the same
code is being executed N times with no specific assertions on the
difference between queue depths. Qdepth testing will be looked at
in system test as an opportunity to increase SW quality.
Change-Id: I5328a43f57cbfa2afc9145c828b6e968dcab310d
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454507
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
For test setup only, each time a UT would run several params, like
the number of drives in the test, would be based on a random value
which is not optimal for UT. This patch just selects a reasonable
fixed values and uses them every time.
This can save up to 4 seconds per run depending on the values that
were randomly chosen (worst case) vs what is in this patch.
There is value in some read/write test cases in using different
strip sizes however. Enabling multiples values for the tests where
it adds value will come in following patches as will removal of
more random numbers like # of channels.
Change-Id: I1b9d44b70ae81af0dcf53ae4a56e31c9c9add39e
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454505
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
General cleanup, first in a series of patches coming soon...
Change-Id: Ibed727559af22c6febb1aad2bb8320a765814144
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454371
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This patch allows multiple iovecs as argument in spdk_dif_generate_stream.
Subsequent patches will support DIF strip and insert in SPDK NVMe-TCP
target based on the patch series.
Change-Id: I1f3d6c5b9f924bb52525e1611db403846d087563
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453756
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
As a subsequent effort, this patch changes the interface of
spdk_dif_generate_stream to accept SGL data buffer.
This patch allows only a single iove. The next patch will allow
multiple iovecs.
Change-Id: I56f901d73ca3b9da4b56c213ebafcd7706b1fef8
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453755
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This patch allows multiple iovecs as argument of
spdk_dif_set_md_interleave_iovs.
Subsequent patches will support SGL data buffer in
spdk_dif_generate_stream too. UT code tests only
spdk_dif_set_md_interleave until then.
Change-Id: I7ac03a3c8f7bcd922af4f29b404ebf3acc4b89e5
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453736
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Currently iSCSI target have used a single contiguous data buffer
both for read and write I/O. Hence spdk_dif_set_md_interleave_iovs
accepts a single contiguous data buffer and its size as arguments.
On the other hand, NVMe-TCP target recently has changed to use
SGL data buffer instead.
DIF strip and insert will be supported in NVMe-TCP target next,
and updating spdk_dif_set_md_interleave_iovs to accept SGL data
buffer will be helpful.
This patch changes the interface of spdk_dif_set_md_interleave_iovs,
but allows only a single iovec. The next patch will allow multiple
iovecs.
Change-Id: I31b09814f8ec920e463a5b1be8fb88cad7d277fb
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453735
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This patch changes UT so that bdev modules have async init.
It demonstrates issue with triggering assert in init path,
when bdev modules are reinitialized multiple times.
Change-Id: I9b2b16d8ac53bac6a929f6929ceedb70b250c500
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454618
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
This change unifies the DIF library to use dif_sgl throughout.
Change-Id: I60addcf05e75b823e4dfb216122bf46edbc42e78
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454528
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The struct _iov_iter has been used to iterate the passed iovec array.
Subsequent patches will share the struct among iteration and
creation. To clarify this update, rename the struct _iov_iter to
_dif_sgl. The name sgl has been already adopted widely in SPDK.
Change-Id: Iab81bcb0658fbd0e39305e045c3d0aadba8fc55f
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454525
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Instead of linking to the real sock library in the unit tests,
link to a mocked up version like we do with the env.
Change-Id: I9607f135c6af86e09fa52badf44897f90ce94521
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/454492
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Add the unit test of the public function nvme_request_check_timeout().
Change-Id: I6b51cc3985b1dd306fa85f3aee2be847e90d8807
Signed-off-by: JinYu <jin.yu@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453781
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
This will (finally) enable resets for fabrics
controllers.
Move some of the work previously done in enable_admin_queue
up to this new disconnect/connect logic.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I6239f0c0f36192db921d33f2322b1874b9382a01
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453939
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The RDMA transport was the only one implementing this
function, and it only does a connect - not a disconnect
followed by a connect.
A later patch will add a matching disconnect function.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Ib68eb0ff2f8e59f437d6d8831bb37dfddf83e9a4
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453929
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
In working on a future patch to queue compress operations, I found
some corruptions in our mbuf pool stemming from an inconsistency
in using mbuf macros when constructing a compress operation and
how we allocated and freed both the pool and the mbufs.
This also fixes an issue that I hadn't addressed yet with freeing
chained mbufs. Use of the mbuf macro to free them instead of the
generic spdk functions takes care of that for us.
Change-Id: I7b29a0d740ab745574698c721d575d8a735ad5cb
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453028
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
On init, we pass reducelib the address of our params structure
so that the volume size is updated accordingly. On load however,
there was nothing to set the volume size so any load of a previously
created compress volume would result in a 0 length bdev.
Change-Id: I7643c79fa2e664115fd25df064ff1c74d82e358b
Signed-off-by: paul luse <paul.e.luse@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/452906
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
We used to rely on lcore >= 0 for sessions that are
started (have their pollers running) and in order to
prevent data races, that lcore field had to be set from
the same thread that runs the pollers, directly after
registering/unregistering them. The lcore was always
set to spdk_env_get_current_core(), but we won't be able
to use an equivalent get_current_poll_group() function
after we switch to poll groups. We will have a poll group
object only inside spdk_vhost_session_send_event() that's
called from the DPDK rte_vhost thread.
In order to change the lcore field (or a poll group one)
from spdk_vhost_session_send_event(), we'll need a separate
field to maintain the started/stopped status that's only
going to be modified from the session's thread.
Change-Id: Idb09cae3c4715eebb20282aad203987b26be707b
Signed-off-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/452394
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Add the UT test case to cover below function:
spdk_iscsi_portal_grps_destroy()
Change-Id: I910b1066ff306039af8d4634122f894ffb3d66e1
Signed-off-by: GangCao <gang.cao@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453499
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Replaced the unnamed unions with named ones. It makes the assignments
easier (it allows for direct assignment instead of having to choose the
correct union member).
Change-Id: I130233a096070092275a040e73cbaf36106ae1ab
Signed-off-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453682
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Darek Stojaczyk <dariusz.stojaczyk@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
This reduces some repeated code. I could have made both paths
call spdk_thread_exit(), but I want to add some stronger checks
around the tls_thread there eventually that wouldn't be valid
in the other path.
Change-Id: I61e1484536d8aef05f120d9ed394312b41f8445a
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453575
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This transport function is a complete nop now, so
remove it.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I5cc6ac75795a3cf5311f24e2ac293fb53d4b9f8c
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453487
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This will allow us to move more of the reset-related
functionality to the common layer, as part of enabling
resets for fabrics controllers.
The transport qpair_enable and qpair_fail functions
acted similarly - so those are both removed now and
replaced with this new qpair_abort_reqs function.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I9486630ad5b807239b0b5bcde50e8cfd313695d3
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453486
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
The nvme_qpair_disable functions will be going away in
an upcoming patch, so move this one bit of functionality
into a helper function in advance.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I61c2de535c2230b988d56dea13b00f39cb59dcfa
Reviewed-on: https://review.gerrithub.io/c/spdk/spdk/+/453483
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
