nvmf_get_ana_log_page used req->data to store the log page result.
While the req->data only contains the first iov, if req->iovcnt is
larger than 1, the req->data may not hold the complete log page; and
even worse, the log page result may be written to invalid address and
cause memory corruption.
The following patch will fix the same issue for other commands in
nvmf_ctrlr_get_log_page.
Fix#1946
Signed-off-by: Jiewei Ke <jiewei@smartx.com>
Change-Id: I495f3be05c82be5cd53609772c655c8924b9179f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7923
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Mellanox Build Bot
Since we will reuse send_pdu for other purpose in the next
patch.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Iee5166131b70a25bc13aaa847bfc9066231f31a9
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/8028
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Community-CI: Mellanox Build Bot
Loading subsystems and restoring state from a JSON config file is useful
outside of the SPDK application framework, so move it to lib/init.
Change-Id: I7dd3ceace2e7b1b28eef83c91ce6a4eedc85740e
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6645
Reviewed-by: Tom Nabarro <tom.nabarro@outlook.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Before this patch idle_tsc was sum of all idle tsc of all
threads running on a reactor.
There are cases when no threads are present on the reactor,
and _reactor_run() spins doing nothing.
To give more accurate representation of the reactors state,
the idle_tsc now adds time spent doing idle spinning.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: If797b2a03507d17b07367d56d5f6c40cefbbbd49
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7900
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
tsc_last value is used to update thread stats
during _reactor_run(). See:
spdk_thread_poll(thread, 0, reactor->tsc_last);
If no threads were present on the reactor,
this value got outdated and resulted in
adding time reactor spent with no threads to
stats of the first thread placed on that reactor.
This patch fixes thread stats by making sure
that argument to spdk_thread_poll() is up to date.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I0c35fdba1b63b6ee19a5a2b34751090839cb2438
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7845
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
This patch does not change the UT in functional way.
Added accounting of last_tsc and spdk_get_ticks() similar
to the real application.
First the reactor_run() [not _reactor_run()] starts
reactor->tsc_last to current time. UT now set it at the start
and never touch it again directly.
Second the spdk_get_ticks() is updated to the elapsed time
to simulate flow of time, and make sure that its further
usage is up to date to the current time.
Fixed typo in test case description for test_reactor_stats.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Iaa2eb00fa3bffc2f21f1692da0259f1d023086b8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7904
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Community-CI: Mellanox Build Bot
This is useful for applications even if they elect not to use the SPDK
event framework.
This doesn't shift everything in one go - just the subsystem
initialization logic. Configuration file loading also needs to move
in a separate patch later.
Change-Id: Id419df1045442d416650ed90e5ee78adfdd623d7
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6641
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Get all of the hot stuff to the first cache line.
* Shrink the xfer enum to one byte (it only has 3 values).
* Pull out the dif enabled flag form the dif structure so it
can be access separately
* Rearrange the members
Change-Id: Id4a2fe90a49c055a4672642faac0028671ebfae9
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7827
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This patch changes the order of IDENTIFY_ACTIVE_NS and CONSTRUCT_NS
controller states. It is required to further improve memory management
for namespaces by allocating memory only for active ones.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: Ie540442b1bd9e897afcbaa4319c139109dd0c515
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6503
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Previous implementation allocated memory just once at the beginning of
active NS list retrieval procedure. It allocated memory for maximum
possible number of active namespaces, i.e. 'cdata.nn'.
This patch changes allocation logic. One page is allocated at the
beginning. If more is needed, reallocation is done with one more
page.
This patch also removes SPDK_MALLOC_DMA flag from allocation since we
don't do RDMA directly into this buffer.
Signed-off-by: Evgeniy Kochetov <evgeniik@nvidia.com>
Change-Id: Iaa80c4d70c54daaf71dcbf755c63a01a1d83b772
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6502
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Use the macros for red black tree provided by Free BSD to manage
timed pollers efficiently.
Allow RB_INSERT() to insert elements with duplicated keys by changing
the compare function to return 1 if two keys are equal.
Check the return code of RB_INSERT() because this is the first use case
for RB tree macros in SPDK. We did the same for RB_REMOVE() by
adding another temporary variable but we remove it from this patch
because it is not so important compared with RB_INSERT().
When a timed poller is inserted, update the cache for the closest (leftmost)
timed poller only if the tree was empty before or the closest (leftmost)
timed poller was actually changed. We do not have to use RB_MIN()
because all duplicated entries are inserted on the right side.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibe253ca8eecc10116548b5eedbcdba8fb961b88d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7722
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This change is a preparation to first dequeue the closest timed poller
always when it is expired. Previously the poller_remove_timer() calls
were not consistent and difficult to follow.
spdk_poller_pause() sets poller to PAUSING even when it in RUNNING
and move it to PAUSED after returning from its context.
If spdk_poller_pause() and spdk_poller_resume() are called while poller
runs, it is moved to WAITING. Hence thread_execute_poller() and
thread_execute_timed_poller() ignore such cases.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I29340613a2ec0c3529d0886f4d81c0a0fdf8745d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7908
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Add a little complex test cases to avoid regression by the following
patches.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I1c94edd913f0a582868e355be085a1faf9bd1a94
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7913
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
This API was removed previously, so remove remaining
references in map file and unit tests.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Iba2f6a5f5ba590d3996dc133c8181083a33d7405
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7963
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Currently we allocate buffers perf each SGL descriptor.
That can lead to a problem when we use NVME bdev with
PRP controller and length of the 1st SGL descriptor is
not multiple of block size, i.e. the initiator may send
PRP1 (which is SGL[0]) which end address is page aligned
while start address is not aligned. This is allowed by
the spec. But when we read such a data to a local buffer,
start of the buffer is page aligned when its end is not.
That violates PRP requirements and we can't handle such
request. However if we use contig buffer to write both
PRP1 and PRP2 (SGL[0] and SGL[1]) then we won't meet
this problem.
Some existing unit tests were updated, 1 new was added.
Fixes github issue #1853
Change-Id: Ib2d56112b7b25e235d17bbc6df8dce4dc556e12d
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7259
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
When we introduce RB tree, getting the closest timed poller is not
O(1) but O(log N). To mitigate such delay, cache the closest timed
poller into thread, and update the cache when its content is changed.
Add unit test cases for this change. They will also clarify the current
behavior of spdk_poller_unregister() and spdk_poller_pause() for
timed pollers.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ibb98a54c261859a3210034038d3953e5c93ef8aa
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7720
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Community-CI: Mellanox Build Bot
Some systems may have page size other than 4096 bytes
Change-Id: Id56bb1566fff480edbe1a293121fc7a68c74252a
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7820
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Use spdk_thread_get_last_tsc() and spdk_thread_get_stats() in
unit tests for reactor. As a result, we can change one inclusion
from spdk_internal/thread.h to spdk/thread.h.
This is the same effort as spdk_poller.
The following patches will move the definition of struct spdk_thread and
enum spdk_thread_state from include/spdk_internal/thread.h to
lib/thread/thread.c.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I24d4a52ecf885b6e7db749616ee1f95b82574dc5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7801
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
It's only for tcp now, but the transport here is rdma. So there is no need to assert.
Signed-off-by: ChengqiangMeng <chengqiangx.meng@intel.com>
Change-Id: Ieffaac9d31a8f9c79a0d9fd226d74268986b7a77
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7823
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
This helps in next patch in series where multiple
completions will be executing.
UT is adjusted since one additional poll is required.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Id72377ddef91e40cdbc2bdea6f33c23309b0ca3d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7642
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
During snapshot creation the original blob becomes
a thin provisioned blob that will only the diff of data after
snapshot creation.
Despite the comment in the UT the number of polls before issuing
blob write was hitting blob BEFORE it swapped with new one.
Issuing I/O during this period shall check for io freeze
before checking cluster allocation.
Otherwise bs_io_unit_is_allocated() hits assert for thin
provisioned blob. This is because cluster map of blob is
empty, but properties have not been updated yet.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I742e1a50b14d456ae1e6de13b5111caec3e8322c
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7641
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
ctrlr_discovery.c doesn't need this #include.
Including it causes bdev_module.h types to be
emitted to the debug symbols at least with some
compilers, which can result in unwanted abidiff
errors.
The unit tests do need it, so just include it
there instead.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: Iad28f9778ce08b11b52325658583ae9032295f3a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7813
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
The library itself doesn't need it. The unit tests
do need it, so just include it there.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I9aefd303ae12928d45141029436509f185105bd3
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7812
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Michal Berger <michalx.berger@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Nvme-cli uses NVME_IOCTL_IO_CMDs for "io-passthru"
commands to cuse devices. This patch adds support
for that IOCTL.
Signed-off-by: Curt Bruns <curt.e.bruns@gmail.com>
Change-Id: I20e0ac91ba08fce91bc5da1f4a1e454058cdd1e7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7741
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
The nvme cuse IOCTLs are actually creating passthru commands
that can be either IO passthru commands or admin commands.
Renaming the routines to correctly reflect that should limit
the confusion when reading the code. Passthru commands that
are admin commands will go to the spdk_nvme_ctrlr_cmd_admin_raw
interface and passthru commands that are IO will be sent to the
spdk_nvme_ctrlr_cmd_io_raw interface.
Signed-off-by: Curt Bruns <curt.e.bruns@gmail.com>
Change-Id: I8d427fe8b5f503fdb2d193236c77d410d5b13886
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7740
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Purpose: We will also support the kernel idxd driver, so we do not
need export this feature in the module file.
Change-Id: I965e031497920f527962ba187bccd81de6977b8f
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7336
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This is prepared for using the hardware offloading
engine in accel framework. And some fields in nvme_tcp_pdu
needs to be DMA addressable.
Change-Id: I75325e2cd7ff25fe938bea0ac9489a5027e3e0e9
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7770
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
This is used to prepare using the accel framework to calculate
the crc32 because some fields in this structure needs to be allocated
in DMA addressable memory.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: Ib8def5596e60f4702709da647145c4e2b6d6848f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7767
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
We cannot rely on DSM/DEALLOCATE as a write zeroes
alternative, even if DLFEAT reports that deallocated
blocks will be read as all zeroes. DEALLOCATE is
advisory, meaning that blocks may not actually be
deallocated. In cases where they are not deallocated,
they will not be read back later as zeroes.
QEMU 6.0 started reporting DLFEAT as returning zeroes
for deallocated blocks but for some of our write
zeroes tests, blocks aren't actually deallocated.
We may be able to add quirks in the future if we know
that a controller reliably deallocates blocks, but
for now we need to revert this completely.
Note that since bdev/nvme module now does not support
write zeroes in any cases, we need to disable the
write zeroes call in the unit tests.
Fixes issue #1932.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I79f0673774b621a9ffcc46891728cc7719e34cdb
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7723
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This will help us to add unmap split function, also
remove bdev_io_type_can_split() because we changed
to use swith(io_type) ... case now.
Change-Id: I449d6a9f5bf2d0b43dd124bbfc9e1ca2afddc15a
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7516
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Purpose: This patch is used to prepare to add the kernel
idxd support later.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Change-Id: If89665f95d622c7342ab75050664158ec6fc615a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7330
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
(Note: this patch was previously applied as b32cfc46 and then reverted
as 63642bef.)
Today the in-guest nvme device shows physical_block_size=512 even though
the backend iSCSI bdev supports physical_block_size=4K
iSCSI targets exposes physical block size using
logical_block_per_physical_block_exponent in READ_CAPACITY_16
NPWG is one of the way to let Linux nvme driver set
physical_block_size of the nvme block device.
This patch adds spdk_bdev.phys_blocklen which is updated if the iSCSI
backend exposes physical_block_size.
Later phys_blocklen is used in nvmf to set NPWG and NAWUPF to report
back during NS identity.
Linux driver uses min(nawupf, npwg) to set physical_block_size.
Similarly in scsi_bdev fill lbppbe in READ_CAP16 response
based on spdk_bdev.phys_blocklen.
Fixes#1884
Signed-off-by: Swapnil Ingle <swapnil.ingle@nutanix.com>
Change-Id: I0b6c81f1937e346d448f49c927eda8c79d2d75c0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7739
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
1) use spdk_bdev_get_name() accessor
2) use __SPDK_BDEV_MODULE_ONLY #define
The latter allows nvmf to just get the spdk_bdev_module
definitions and APIs that it needs for claiming bdevs
for purposes of avoiding the same namespace used in
different subsystems.
This also ensures that future changes to structures
like spdk_bdev and spdk_bdev_io will not cause
lib/nvmf so version changes.
Note: we include bdev_module.h explicitly in the
nvmf/subsystem unit tests now, before including
subsystem.c, because the unit tests do depend on
knowing the internal structure of spdk_bdev.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I2f499a741d19f4749eadb402641f28137245fd23
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7738
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Anil Veerabhadrappa <anil.veerabhadrappa@broadcom.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
It is already set by nvmf_tcp_req_pdu_init
when we get the pdu. So we do not set it again.
Change-Id: I034bbc46e600afd802457c0b152e303f16bafba3
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7714
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
This reverts commit b32cfc467b.
This commit fails the ABI checks and only got through because the checks
were disabled until 21.04 hit.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: Id26b8f8ba551193d99b1ccbd31b35378b4095a20
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7731
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Today the in-guest nvme device shows physical_block_size=512 even though
the backend iSCSI bdev supports physical_block_size=4K
iSCSI targets exposes physical block size using
logical_block_per_physical_block_exponent in READ_CAPACITY_16
NPWG is one of the way to let Linux nvme driver set
physical_block_size of the nvme block device.
This patch adds spdk_bdev.phys_blocklen which is updated if the iSCSI
backend exposes physical_block_size.
Later phys_blocklen is used in nvmf to set NPWG and NAWUPF to report
back during NS identity.
Linux driver uses min(nawupf, npwg) to set physical_block_size.
Similarly in scsi_bdev fill lbppbe in READ_CAP16 response
based on spdk_bdev.phys_blocklen.
Fixes#1884
Signed-off-by: Swapnil Ingle <swapnil.ingle@nutanix.com>
Change-Id: I0b6c81f1937e346d448f49c927eda8c79d2d75cf
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7310
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
There are three modules implementing the bdev-zone API:
bdev_nvme, bdev_ocssd, and vbdev_zone_block.
For all three modules, the number of zones can be calculated using:
block_count / zone_size.
To avoid this calculation being performed everywhere, create a helper
function in bdev_zone.h, together with the other zone APIs, such that
a user can easily get the number of zones.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Change-Id: I2967b15a604ab8bf4420588e7510b9820762f925
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7451
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
tcp transport doesn't send a response capsule when
c2h_success is set even if cdw0 or cdw1 are non-0.
Signed-off-by: Ed rodriguez <edwinr@netapp.com>
Signed-off-by: John Meneghini johnm@netapp.com
Change-Id: Ieba81fcc50342a2009f7931526e6f8392e26b6a5
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6808
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Konrad Sztyber <konrad.sztyber@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
New UT verifies number of extent page writes for
thin provisioned blobs.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: I6b52195d26c3c1414ca862b03e8a3043bbe29b42
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7017
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
This patch addresses couple issues:
1) Before issuing the md syncs the previous steps in test left
blob state in dirty state already. The resize never had a chance
to apply. This patch adds a proper md sync and polls for completion.
2) Changing blob state is something that should be done via API.
In order for dirty state to apply immidietly set_xattr is now used instead.
3) Verify test state in callbacks to make sure not only the number of
completions is correct, but their order.
This patch is introduced because of the test originally worked
only because of the extent pages always writing out its pages.
The second sync always was delayed because of this.
Meanwhile that should not be the case, since no MD or EP modification
was done.
Later in the series Extent Pages are fixed, but this test remained incorrect.
Signed-off-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Change-Id: Iac17c27f6ff83f2b79835aa6e48472d5293c44d0
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7233
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Community-CI: Mellanox Build Bot
This function finds a placement_id that does not have a group
associated with it.
Change-Id: I1306690e980fd4661f46dba9fb283f048a962eba
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7223
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
When the format command is issued, the kioxia drives responds with "NS Attr change" notices.
In the callback function of the notice, the CQ Head Doorbell is updated twice with the same
value while issuing the Active NS list & identify NS commands.
Fixes: #1701
Signed-off-by: G.Balaji <gbalajieie@gmail.com>
Change-Id: I8cc80fba0a226c22753e605ef3129602a9313ce7
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7149
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Also update the UT.
Change-Id: I6086bf4cafca8a917a467490955d7df0ba8930d5
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7495
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Since the maps are unique to modules, they can store the group_impls
directly.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Change-Id: I7f11db558e38e940267fdf6eaacbe515334391c2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7222
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This allows for different policies per module, as well as overlapped
placement_id values.
Change-Id: I0a9c83e68d22733d81f005eb054a4c5f236f88d9
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7221
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Test scenario is as follows.
Some iSCSI initiator sends a Data-OUT PDU sequence such that the size of
the data segment of any Data-OUT PDU is not block size multiples.
Test if such complex Data-OUT PDU sequence is processed correctly.
Desired Data Transfer Length is 5 * SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH / 2.
Number of Data-OUT PDUs is 4. Length of the data segment of the first two PDUs are
SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH / 2 - 4. Length of the data segment of the
third PDU is SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH. Length of the data segment
of the final PDU is SPDK_ISCSI_MAX_RECV_DATA_SEGMENT_LENGTH / 2 + 8.
Three data buffers should be used and three subtasks should be created and submitted.
The test scenario assume that a iscsi_conn_read_data() call could read
the required length of the data and all read lengths are 4 bytes multiples.
The latter is to verify data is copied to the correct offset by using data patterns.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I5e3939d07cd4f50fe3dcf659a18a9f8fcbe01e07
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6584
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Community-CI: Mellanox Build Bot
Test sharing data buffer among multiple Data-OUT PDUs.
Allocate real data buffers and the iscsi_conn_read_data() stub writes
data patterns into them.
The data pattern is to write offset per 4 bytes. This requires read
length to 4 bytes multiples but the requirement will be acceptable.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I87c673c3bb0ada2afebb9332af9525cd9d7388f2
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6568
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
This prepares for an upcoming patch to fix issue #1701 which
requires handling async events outside of the check
completions loop.
Fixes: #1701
Signed-off-by: G.Balaji <gbalajieie@gmail.com>
Change-Id: I4985d814903143511383172b1a443580db33a78f
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7416
Community-CI: Broadcom CI
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
We can return error status when processing RELEASE2 without
a reservation, also add a UT to cover this case.
Fix issue #1898.
Change-Id: I56ffa8eabfc0409307500f8740cb627aab9d2f0b
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7379
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Karol Latecki <karol.latecki@intel.com>
Reviewed-by: Tomasz Zawadzki <tomasz.zawadzki@intel.com>
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
This is necessary to the following patches to test reset continuation.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I20e0a6b96694eb06adadfbe8e20f73380645ea43
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7326
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
It is more readable to use const variable rather than raw number.
memset is the way to initialize variable size array.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I42f3f34422ea96e06a99bd6cc02e0e91349a4009
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7323
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Community-CI: Mellanox Build Bot
Previously when attaching a ctrlr, all namespaces had not been
populated. Hence we had to populate each namespace manually.
It is more normal if all namespaces are populated when attaching the
corresponding ctrlr.
This patch does such change.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I55d9c444c492ba6e44a609eac81b1ef25a7190a8
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7313
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Previously spdk_nvme_probe_poll_async() had processed all attaching
controllers. Hence it was not easy to attach multiple controllers in
unit tests.
Besides, add a check to exclude duplicated controllers into ut_attach_ctrlr().
If the target is any SPDK library, we should insert another patch
only to do code movement, but this is a unit test file, and so it
will be acceptable to include code movement in the same file.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I9e8eba6a67b2a6d0df384214ff84aa5b0c602217
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7312
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
We only need SPDK_CU_ASSERT_FATAL to check for
NULL pointers. Other checks should just use
CU_ASSERT and variants.
There are some nvme_ns_cmd_ut checks that are
using SPDK_CU_ASSERT_FATAL unnecessarily. Let's fix
them.
Found during investigation of issue #1882.
Signed-off-by: Jim Harris <james.r.harris@intel.com>
Change-Id: I0b313e44e2ed05554783933e7d4bbc5f07a7e84a
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7290
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Check if qpair has a poll group during the connect process,
use poll group's statistics or allocate own structure per
qpair. That is done due to not all applications use poll
groups and we want to avoid "if (qpair->group)"
conditions in data path.
Admin qpair always allocates its own statistics
structure but the statistics are not reported
since this qpair is not attached to a poll group.
Statistics are reported by spdk_nvme_perf tool
if --transport-stats and in bdev_nvme_transport_statistics
RPC method.
Change-Id: I58765be161491fe394968ea65ea22db1478b219a
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6304
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
These are interface functions that can be used by
an application e.g. spdk_nvme_perf or bdev_nvme
library. The next patches will add usage of these
functions.
Change-Id: I33b88e0e713c2ea5967f9241885e3257c5070577
Signed-off-by: Alexey Marchuk <alexeymar@mellanox.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6300
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
bdev_nvme_delete() calls spdk_nvme_detach() in the end. However,
previously spdk_nvme_detach() stub did nothing and ut_detach_ctrlr()
was called separately if ctrlr wass attached by ut_detach_ctrlr().
This was to differentiate the two cases, ctrlr is statically assigned
or dynamically attached by ut_detach_ctrlr().
This might be a little confusing. Hence by adding a flag, attached,
to ctrlr, merge ut_detach_ctrlr() into spdk_nvme_detach(), and remove
ut_detach_ctrlr() calls.
Besides, change one SPDK_CU_ASSERT_FATAL to return NULL because the
other cases do that and the callers for ut_attach_ctrlr() already have
SPDK_CU_ASSERT_FATAL.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I2a73f57c6031819d3ae441a6874127ff5d53fc04
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7311
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
This will make the following change simpler and testing
bdev_nvme_find_io_path() will be good.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Iac82bdba88e4abfa41c2ce04f10ce41a6b7dbd71
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/7106
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Aleksey Marchuk <alexeymar@mellanox.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Paul Luse <paul.e.luse@intel.com>
The following patches will aggregate multiple Data-OUT PDUs into a
single write subtask and we will not be able to use reqh->buffer_offset
to track the current offset of large write I/O to submit write subtasks.
On the other hand, each iscsi_task or iscsi_subtask is only read or write
Hence rename current_datain_offset of iscsi_task by current_data_offset
in this patch.
The next patch will use it to track the current offset of large write I/O
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I922582c5b9474a3c512f81d0f0425158a38a9a8d
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6423
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
The following patches will want to aggregate multiple Data-OUT PDUs
into the same data buffer, but it will be 64KB at most.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: I72eabbeae0b027c2fbff2a5837d180b06b0a1b49
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6418
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Ziye Yang <ziye.yang@intel.com>
Reviewed-by: Jim Harris <james.r.harris@intel.com>
The following patches will change the handler for Data-OUT PDU to
submit subtask only when 64KB data is read or F bit is set.
Previously, we had created a subtask when processing header and
before reading data segment. Creating a subtask beforehand is not
convenient for the following changes.
Hence create a subtask after reading data segment.
If LUN is removed while processing the Data-OUT PDU, the corresponding
primary task will be terminated by iscsi_clear_all_transfer_task(),
and any subtask completion is not sent to initiator. Hence we can
reject the received Data-OUT PDU safely.
Signed-off-by: Shuhei Matsumoto <shuhei.matsumoto.xt@hitachi.com>
Change-Id: Ifb6d6988676080b458b31d12fef065f3c1de0cb6
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/6415
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Community-CI: Mellanox Build Bot
Reviewed-by: Jim Harris <james.r.harris@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
The hotplug lib can be used for pcie devices
such as nvme, virtio_blk and virtio scsi.
For the sigbus handler, there is only one in a
process and it should handle all the devices.
And align nvme to the hotplug lib
Add the ADD uevent support for allowing the
device hotplug.
Change-Id: I82cd3b4af38ca24cee8b041a215a85c4a69e60f7
Signed-off-by: Jin Yu <jin.yu@intel.com>
Reviewed-on: https://review.spdk.io/gerrit/c/spdk/spdk/+/5653
Community-CI: Broadcom CI
Community-CI: Mellanox Build Bot
Tested-by: SPDK CI Jenkins <sys_sgci@intel.com>
Reviewed-by: Ben Walker <benjamin.walker@intel.com>
Reviewed-by: <dongx.yi@intel.com>
Reviewed-by: Changpeng Liu <changpeng.liu@intel.com>
